Pro-Elec PEL00941 User manual

1
Model: PEL00940
2kW CONVECTOR HEATER WITH TIMER
and PEL00941
2kW CONVECTOR HEATER WITH TIMER AND FAN

2
IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
• Check that the voltage indicated on the rating plate corresponds with that of the local
network before connecting the appliance to the mains power supply.
• To avoid re or shock hazard, plug the appliance directly into a suitable 220-240V AC
electrical outlet. DO NOT use an external timer, separate remote control system, and
extension cable or external adaptor with the appliance. Do not overload the circuit.
• This heater must not be located immediately below a socket-outlet.
• To disconnect the appliance, turn the control switch to “OFF” BEFORE removing the
plug from main power outlet.
• When unplugging, be sure to pull by the plug and not the cord.
• Always unplug the appliance when not in use.
Note: the timer clock will require re-setting to the correct time if power is disconnected.
• Discontinue use if plug or outlet becomes hot. It is recommended that the outlet be
checked and replaced if plug or outlet is hot to touch.
• Do not abuse or damage the power cord. Fully unwind the cord before use as a
coiled cord may overheat. Do not allow the supply cord to touch hot surfaces.
• DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners,
or the like. Position the cord away from tra󰀩c area and where it will not cause a trip
hazard.
• Ensure that the supply cord is kept away from heat or sharp edges that could
cause damage.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust vent
opening as this may cause an electric shock or re, or damage to the appliance.
• DO NOT operate the appliance with a damaged cord or plug, or after the appliance
malfunctions, has been dropped or damaged in any manner. If the supply cord is
damaged, DO NOT attempt to service this appliance yourself. Return it to a qualied
service agent for mechanical adjustment, or repair.
WARNING: In order to avoid overheating, DO NOT COVER the heater.
• To prevent a possible re, DO NOT block air intakes or exhaust vents in any manner.
DO NOT use on soft surfaces, like a bed, where openings may become blocked.
• DO NOT move the appliance when it is operating. Only move the appliance when
cool.
• The appliance is hot when in use. To avoid burns, DO NOT touch any hot surfaces.
Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and
curtains at least 3 ft (0.9 m) from the front of the heater and keep them away from the
sides and rear.
• This appliance is not intended for use by persons (INCLUDING CHILDREN)
with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use of
the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• Do not use this heater in the immediate surroundings of a bath or a shower.
• This appliance is not intended for use in bathrooms, laundry areas and similar indoor
location where this it may come in contact with water.
• Do not immerse any part of this appliance or supply cord in water.
• DO NOT use in areas where gasoline, paint, or ammable liquids are used or stored.
• This appliance is designed for indoors ONLY.

3
ASSEMBLY
Fitting the Feet
• Carefully turn the unit upside down. Using the four 12mm screws provided, a󰀩x
the feet to the underside of the heater (see right).
OPERATION
• Before connecting the appliance to the mains, make sure that all switches are set
to the “OFF” position.
• Insert the plug of the heater into the main socket.
• Adjust the thermostat to a desired temperature level.
• Turn on the heating element using the two rocker switches on the side panel. They
will illuminate when the heating elements are on.
• The third rocker switch can be used to turn the fan on to circulate warm air in the
room when the heating elements are
on (PEL00941 only).
• The fan can be used with the
heating elements switched o󰀨 to
help circulate cool air. The switch will
illuminate when the fan is on.
Note: It is normal when the heater is turned on after a period of no use for it to emit
some odour. This will disappear after the heater has been on for a short time.
USING THE TIMER
• Set the time by adjusting the clock wheel in a clockwise direction only, so that the
arrow points to the current time.
• Set the slide switch position to the clock setting.
• Set the time periods required for heating by sliding
the red teeth outwards. Each tooth represents
approximately 15 minutes.
• Sliding the teeth back in to the centre will turn
the heater o󰀨 for that period. To run the heater
continuously set the slide switch to the (I) position.
• In position “O”, the timer continues to run but no
power is fed to the heater.
I
0

4
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT
When this product has reached the end of its life it must be treated as Waste Electrical &
Electronics Equipment (WEEE). Any WEEE marked products must not be mixed with general
household waste, but kept separate for the treatment, recovery and recycling of the materials used.
Contact your local authority for details of recycling schemes in your area.
Made in China
PO Box 13362 Dublin 2
PR2 9PP
Man Ref 1.2
As with all portable heaters -
This product is only suitable for well insulated spaces or occasional use.
SPECIFICATIONS
Model PEL00940 PEL00941
Rated Voltage 220-240VAC 220-240VAC
Frequency 50Hz 50Hz
Rated Power 1800-2000W 1800-2000W
Heat Output
Nominal heat output Pnom 1.8-2.0kW 1.8-2.0kW
Min heat output Pmin 0kW 0kW
Max heat output Pmax 2.0kW 2.0kW
Auxiliary electricity consumption
At nominal heat output elmax 0kW 0kW
At minimum heat output elmin 0kW 0kW
In standby mode elsb N/A N/A
With mechanical thermostat room temperature control YES YES
With day timer YES YES
Fan assisted heat output NO YES
CLEANING & MAINTENANCE
• Always unplug the heater from the wall socket and allow it to cool down before
cleaning.
• Clean the outside of the heater by wiping it with a clean, damp cloth.
• Do not use any chemicals, abrasives or solvents that may damage the heater.
• Do not allow any water to enter the inner appliance.
• To store the heater, place it in a clean, dry environment, ensuring it is protected
from dust.
NEVER LEAVE THE HEATER UNATTENDED WHEN IT IS IN USENEVER LEAVE THE HEATER UNATTENDED WHEN IT IS IN USE