Pro-Elec PELL0004-WHT User manual

Model: PELL0004-WHT and PELL0004-BLK
2KW CONVECTOR HEATER
1

Please read these instructions carefully before use and retain for future reference.
IMPORTANT SAFETY INFORMATION
WHAT’S INCLUDED
• Heater unit
• User manual
• Feet - 2 off
• Attaching screws
• Check if the voltage indicated on the rating plate of the appliance corresponds to
the local mains voltage before you connect the appliance.
• Use this heater only as instructed in this manual. Any other use not recommended
by the manufacturer may cause re, electric shock, or injury to persons.
• A worn mains socket may result in over-heating of the plug and socket. If this
occurs consult a qualied electrician.
• Arrange mains cord away from any trafc area and where it will not become a
hazard to users and ensure that the supply cord is kept away from heat or sharp
edges that could cause damage.
• The heater must not be located immediately below an electrical socket-outlet.
• Do not use this heater with a timer or any device that switches the power on
automatically, as a re risk exists should the heater be covered or place incorrectly.
• In case of improper use, there is a risk of electrical shock and/or re hazard.
• Do not try to repair the appliance by yourself. Please contact with the service agent
or a suitably qualied electrician for maintenance.
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities or lack of experience or knowledge. They
should be given supervision and instruction in the use of the appliance by a person
responsible for their safety.
• The casing of the appliance can become extremely hot during operation. To avoid
burns, do not let bare skin touch hot surfaces. Use the handles when moving this
heater.
• Extreme caution is necessary when used by or near children or vulnerable people.
• This heater is not intended for use near swimming pools, hot tubs and similar
locations. Never locate the heater where it may fall into any water container.
• To prevent a possible re or electric shock, do not block or allow foreign objects to
enter any air intakes or ventilation slots in any manner.
• Do not use oor standing heaters on soft or uneven surfaces where instability may
be caused.
• Do not operate any heater with a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged in any manner.
• Keep combustible materials such as furniture, pillows, bedding, papers, clothes and
curtains at least 1.0m from the front of the heater.
• Do not use in areas where gasoline, paint, or ammable liquids are used or stored.
• Remove the plug from the power outlet and wait until the appliance is completely
cooled off before cleaning or putting into storage.
• To disconnect heater you should turn the controls off then remove plug from outlet.
• Always unplug heater when not in use.
• In order to avoid overheating, do not cover the heater.
• Never leave this heater unattended.
• This heater is for indoor use only.
• Before using this appliance, it must have the supplied feet tted.
WARNING: Do not operate the heater without the feet tted.
• Turn the heater body upside-down on a scratch-free and stable surface.
• Be careful to prevent damage to the cosmetic nish or your oor surfacing.
• Attach the feet to the base of the heater using the screws provided, taking care to
ensure that they are located correctly on the bottom of the heater.
ASSEMBLY
OPERATION
2 3
NOTE: When the appliance is turned on for the rst time, it may release a slight, odour
or smoke. This odour or smoke is a normal occurrence caused by the initial heating of
the internal heating elements and should not occur again.
• The control switch positions are:
0 - Off
750W - Low Heat
1250W - Medium Heat
Both - High Heat
• Check that the heat control switches are both set
to OFF position before plugging the heater into
the mains supply.
• For greater economy, use the high heat setting
initially and then switch to a lower heat setting.
• Rotate the thermostat control clockwise to
increase the temperature that the heater will
switch off when reached.
• When the room temperature falls the heater will turn on again.
NOTE: if the thermostat is set to a high level, if the heat setting is only on low, the
heater will remain on constantly.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL
& ELECTRONIC EQUIPMENT
When this product has reached the end of its life it must be treated as Waste Electrical & Electronics
Equipment (WEEE). Any WEEE marked products must not be mixed with general household waste,
but kept separate for the treatment, recovery and recycling of the materials used. Contact your local
authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Ref 1.0
SPECIFICATIONS
4
CLEANING & MAINTENANCE
• This appliance consists of a robust and maintenance-free casing with a protective
cover. No user serviceable parts are inside.
• Always unplug the heater from the mains supply and allow it to cool down fully
before cleaning.
• Use a clean, damp cloth or a soft brush to clean the outside of the heater.
• Never use abrasive cleaners or chemicals for cleaning that may damage the heater.
• To protect against electrical shock and danger of life, do not immerse cord, plug or
any part of the appliance in water or any other liquid.
• Improper repairs could lead to danger to the user.
• Do not allow any water to enter the appliance.
• To store the heater, place it in a clean, dry environment, ensuring it is protected
from dust.
As is typical for all portable heaters -
This product is only suitable for well insulated spaces or occasional use
Model PELL0004 (All colours)
Rated Voltage 220-240VAC
Frequency 50/60Hz
Rated Power 2000W
Dimensions 620 x 224 x 380mm
Weight 3.1kg
Heat Output
Nominal heat output Pnom 2.0kW
Min heat output Pmin 0.8kW
Max heat output Pmax 2.0kW
Auxiliary electricity consumption
At nominal heat output elmax 1.97kW
At minimum heat output elmin 0.693kW
In standby mode elsb N/A
With mechanical thermostat room temperature control YES