Pro-face FP2600-T41 User manual

FP2600-T41
User Manual
Digital Electronics Corporation

FP2600-T41 User Manual i
It is forbidden to copy the contents of this manual, in whole or in part, except for the
user'spersonaluse,withouttheexpresspermissionoftheDigitalElectronicsCorpo-
rationofJapan.
2) Theinformationprovidedinthismanualissubjecttochangewithoutnotice.
3) Thismanualhasbeenwrittenwithcareandattentiontodetail; however,shouldyou
findanyerrorsoromissions,pleasecontactDigitalElectronicsandinformthemof
yourfindings.
4) PleasebeawarethatDigitalElectronicsisnotresponsibleforanydamages resulting
from the use of our products, regardless of article 3 above.
5) Specificationsset out inthis manual arefor overseas productsonly,and, as aresult,
somedifferencesmayexistbetweenthespecficationsgivenhereandtheJapanese
ones.
AllCompany/Manufacturernames usedinthismanualaretheregisteredtrademarksof
theirrespectivecompanies.
©2001,DigitalElectronicsCorporation
<Note>
Preface
Thankyouforpurchasing Digital’sTFTtypecolordisplaypanel,the 'FP2600-T41'
(hereafter referred to as the FP unit).
TheFPunitis a TFT type colorliquidcrystaldisplaymonitorfor IBM-PC compatible
personalcomputers(SVGAmode).
Pleaseread this manual completelytoinsure the correctuseand complete understand-
ingoftheFPunit'sfunctions. TheFP's analog interface is designed for use with
standard VGA mode. Please be aware that this unit may not be able to be connected
with nonstandard VGA modes. For more details, please refer to this manual's "PC
ConnectivityNotes"section.
The term FP2600-T41 refers to the following unit:
FP2600-T41-24V (AC 24V type)

ii FP2600-T41 User Manual
Other Symbols Used In This Manual
The list below describes the symbols used in this manual.
Explains a situation that requires a moderate amount of caution.
Indicates a word or phrase that has an additional explanation.
A reference point. Describes the word or phrase marked by the as-
terisk (*) and the corresponding number.
Reference pages on related topics.
Thismanual describes safetyinstructions for correctuse of theFP unit. Pleasekeep this
manual close at hand, and refer to it when necessary.
The following symbols are used throughout this manual to ensure the safe use of the FP
unit. Pleasemakesuretofollowallinstructionsgivensincetheyexplainimportantsafety
points.
For the Safe And Correct Use of this Unit:
*1
1),2) Operational steps. Please follow these numbered steps in order to
perform the desired operation.
This mark warns of a situation that could either seriously
injure a person or lead to death if the instruction is ignored
and/or the unit is used incorrectly.
This mark warns of a situation that could either injure a
person or damage property if the instruction is ignored and/
or the unit is used incorrectly.
Warning
Caution

FP2600-T41 User Manual iii
Safety Instructions
For the safe use of this unit, be sure to follow these guidelines:
Warning
Because of the ever present danger of electrical shock, be sure to unplug the power cable
fromtheFPunitbeforepluggingthecable'sotherendintothewall.
Donotusepowerinexcessoftheunit'sspecifiedvoltagerangesinceit may cause a fire or
electricshock.
Because the FP unit contains high voltage parts, an electric shock can occur when disas-
semblingtheunit. Therefore,pleasebesuretoalwaysunplugtheunitbeforedisassembling
it.
Donot modifythe FP unitin any way,since itmay cause afire or electricshock.
Whenchangingthebacklight,besuretoturnofftheunit'spowerfirst,inordertopreventan
electricshock.
Donotusetouchpanelkeystoperformlife-threateningorvitallyimportantsafetyfunctions.
Useseparatemechanicalswitches for such keys.
Ifsubstantialamountsofmetallicdust,waterorliquidsentertheFPunit,turnoffthepower
supplyimmediately,unplugthepowercord, and contactyourlocalFPdistributor.
WheninstallingtheFPunit,besuretofollowtheinstructionsgivenin“Chapter3.Installation
andWiring," toinsureitisdonecorrectly.
DonotusetheFPinanenvironmentwithflammablegas since it may causeanexplosion.

iv FP2600-T41 User Manual
Do not press the screen's touch surface too strongly with either your finger or a hard
object, since the touch surface may be damaged.
Whenthesurfaceof thedisplayscreenbecomesdirtyorsmudged, cleanthedisplaywith
acloth soaked ina neutraldetergent. Do notuse paint thinneror organic solvent.
Donot press onthetouch panel's face withsharp objects, such asamechanical pencil or
screwdriver,sinceitmightdamagetheLCD panel.
AvoidusingorstoringtheFPindirectsunlight,excessivelydustyordirtyenvironments,or
wherechemicals ortheir vapors arepresent in theair.
AvoidrestrictingtheFP'snaturalventilation,orstoringandusingtheFPinanenvironment
thatwillincreasetheFP'sinternaltemperature.
PleaseavoidusingtheFPinareaswheresudden,largechangesintemperaturemayoccur.
Thesechangescancausecondensationtoforminsidetheunit,possiblycausinganaccident.
TheFP'sLCDcontainsastrong irritant. IfthepanelisevercrackedandtheLCD'sliquid
contactsyourskin,besuretowashitwithrunningwaterforatleast15minutes. Ifanyof
thisliquidshouldenteryoureye,besuretoflushtheeyewithrunningwaterformorethan
15minutes,and see a doctorimmediately.
Thecurrentbrightnessofthe LCDscreenwilldependonthescreen's currentdisplayand
theLCD'scontrastadjustment.Anybrightnessvariations that resultarenormalforLCD
displays.
There are minute grid-points on the LCD surface. These points are not defects.
Sometimes crosstalk (shadows appearing on extended display lines) will appear on the
display. This phenomenon is a common attribute of LCD's and is not a defect.
Thedisplayedcolorwilllookdifferentwhenviewedfromanangleoutsidethespecified
viewangle.Thisisalsonormal.
Displaying a single screen image for long periods of time can cause an afterimage to
remain. To correct this, turn the unit OFF for 5 or 10 minutes, then ON again. This
phenomenonisacommonattributeoftheLCD's,andnotadefect. Topreventthiseffect,
youcan: - use the Display OFF feature, if the same image is to be displayed
for a long period of time.
-changethescreendisplayperiodicallytopreventthedisplayingofa
single image foralong period oftime.
Safety Instructions
For the correct use of this unit, please follow these guidelines:
Notes on the FP's Liquid Crystal Display (LCD)
Caution

FP2600-T41 User Manual v
Table of Contents
Preface ........................................................................................................................i
For the Safe and Correct Use of this Unit.................................................................. ii
Warning: Safety Instructions .......................................................................................iii
Caution: Safety Instructions ........................................................................................iv
Table of Contents ........................................................................................................ v
When Connecting to a PC...........................................................................................vii
FP2600-T41 Features..................................................................................................viii
Package Contents ....................................................................................................... ix
UL/c-UL (CSA) Application Notes ...........................................................................x
CE Marking Notes ......................................................................................................x
Chapter 1—Introduction
1-1 Connecting the FP to a PC ..................................................................................1-1
1-2 Optional Equipment ...............................................................................................1-2
Chapter 2—Specifications
2-1 General Specifications (For DC24V) ................................................................... 2-1
1 Electrical Specifications ..............................................................................................2-1
2 Environmental Specifications .....................................................................................2-1
3 Structural Specifications.............................................................................................2-2
2-2 Functional Specifications(For DC24V)................................................................. 2-3
2-3 Interface Specifications(For DC24V) .................................................................2-4
1 Analog RGB Interface .................................................................................................2-4
2 Serial Interface ............................................................................................................2-6
3 USB Interface ..............................................................................................................2-7
2-4 Cable Diagrams ...................................................................................................2-8
1 Pin Connections for the RGB Interface Cable............................................................2-8
2 Pin Connections for the SIO Interface Cable .............................................................2-9
3 Pin Connections for the USB Interface Cable ...........................................................2-9
2-5 Names and Functions of FP Parts.............................................................. 2-10
2-6 Flat Panel (FP) Dimensions........................................................................ 2-11
1 External Dimensions (DC24V) ................................................................... 2-11
2 Installation Brackets ........................................................................................... 2-12
3 FP Installation Dimensions ................................................................................. 2-12

vi FP2600-T41 User Manual
Chapter 3—Installation and Wiring
3-1 Installation .................................................................................................................3-1
3-2 Wiring ........................................................................................................................3-5
1 Power Cable Connection ................................................................................................... 3-5
2 Precaoutions: Connecting the Power Supply....................................................................3-6
3 Precautions: Grounding .....................................................................................................3-7
4 Precautions: Input/Output Signal Lines............................................................................ 3-7
3-3 Operation Mode Setup and Display Positioning .......................................................3-8
1 Operation Mode Setup and Adjustment ...............................................................3-8
2 Front LED Option Mode Display .....................................................................................3-9
3 Display Position Compensation by OSD.......................................................................... 3-10
Chapter 4—Touch Panel Commands
4-1 Command List..........................................................................................................4-1
4-2 Boot-upInitialization ................................................................................................4-2
4-3 Touch Interface Data ..............................................................................................4-3
4-4 Touch Panel Commands..........................................................................................4-5
Chapter 5—Troubleshooting
5-1 Troubleshooting........................................................................................................5-1
1 Possible Device Problems ................................................................................................ 5-1
2 No Display ........................................................................................................................ 5-2
3 Touch Panel Does Not Work ............................................................................................ 5-4
Chapter 6—Maintenance
6-1 Regular Cleaning .....................................................................................................6-1
1 Cleaning the Display ........................................................................................................ 6-1
2 Installation Gasket Check/Replacement ........................................................................... 6-1
6-2 Periodic Check Points .............................................................................................6-2
6-3 Replacing the Backlight ...........................................................................................6-3
INDEX.............................................................................................i - iv

FP2600-T41 User Manual vii
• With vertical 350 pixels, 400 pixels, including 50 pixels at the top and at the
bottom of the screen will be enlarged and displayed at 600 pixels (1.5 times).
SometypesofVGAequipmentmaynotbewithintherangesspecifiedabove,and,therefore,
cannot be connected to the FP.
Also, if the user changes his PC's VGA board, there is the possiblity that the new board
may not be able to be connected to the FP.
When Connecting to a PC
The FP unit's analog interface is designed for standard SVGA mode. The number of dots
(pixels)displayedareasfollows:
Size H Sync. V Sync. Dot Clock Range
800X600 35.156±1KHz 56±1Hz 36.000MHz±1%
800X600 37.879±1KHz 60±1Hz 40.000MHz±1%
640X480 31.469±1KHz 60±1Hz 25.175MHz±1%
640X480 35.000±1KHz 66±1Hz 30.240MHz±1%
640X480 37.861±1KHz 72±1Hz 31.500MHz±1%
640X400 24.827±1KHz 56±1Hz 21.053MHz±1%
640X400 31.469±1KHz 70±1Hz 25.175MHz±1%
640X350 31.469±1KHz 70±1Hz 25.175MHz±1%
720X400 31.469±1KHz 70±1Hz 28.322MHz±1%
720X350 31.469±1KHz 70±1Hz 28.322MHz±1%

viii FP2600-T41 User Manual
High Quality TFT Color LCD Display
Thisunitisequippedwitha12.1inchTFT type color LCD. Its superior brightness and
wideviewingangle,notfoundinordinarylaptoptypeTFTLCD's,widensyourscopeof
applications.
Thescreen's maximum resolutionis 800x 600 pixels,and can display260,000 colors.
Easy Installation In User’s Cabinets and Panels
The FP2600-T41's slim, lightweight, and compact design make installation a snap. It
was designed specifically for use as your IA (Industrial Automation) or OA (Office
Automation)systemmonitor. Theflat,frontpanelprovidesprotectionequivalenttothe
rigorousIP65Fstandard,and,evenwithoutitsoptionalprotectivecover,thefrontpanel
ishighlyresistanttoboth water and dust.
Panel can be used as a VGA Display
Since the FP2600-T41 is equipped with an analog RGB interface, it can be connected
to any PC with standard VGA/SVGA mode. (The PC's clock frequency, however,
mustbewithinthestandard range)
Easy to use Built In Touch Panel
TheFP2600-T41'sbuiltintouchpanelisstandardequipment,allowingtouchpaneldata
to be output to a host PC via input/output commands and an RS-232C cable and USB
cable.Thisisperfectforsystemsrequiringbothtouchpaneloperationanddatamonitoring.
FP2600-T41 Features
The features of the FP2600-T41 are as follows.

FP2600-T41 User Manual ix
The FP's packing box contains the items listed below. Please check to be sure each is
includedandisnotdamaged.
FP unit (FP2600-T41-24V)  
 
 FP2500/2600
User Manual (Contained in plastic case)
Installation Gasket (1)  Installation Brackets (4)


FP2500-T41/FP2600-T41
Installation Guide (1)
Theseitemshaveall beencarefullypackedwithspecialattentionto productquality.
However, should you find anything damaged or missing, please contact your local
distributor immediately for prompt service.
Package Contents
User Manual
Installation
Guide

xFP2600-T41 User Manual
The FP2600-T41-24V is a UL/c-UL (CSA) listed product. (UL file No.E182139)
This unit conforms as a product to the following standards:
ThisUL508 IndustrialControlEquipment
This UL1604 Electrical Equipment for use in Class 1 & 2 - Division 2, or Class 3
HazardousLocations.
This CAN/CSA-C22.2, No.1010-1
MSUREMENT AND CONTROL EQUIPMENT
(Safetyrequirementsforelectricalequipmentformesurementandlaboratoryuse)
FP2600-T41-24V(UL Registration Model: 30B0003-02)
<Cautions>
UL/c-UL (CSA) Application Notes
The FP must be used as a built-in component of an end-use product.
Thisunitshouldbeinstalled in thefrontfaceofametalpanel.
Ifthisunitisinstalledsoastocoolitselfnaturally,besuretoinstallitinaverticalpanel.
Also, be sure that the FP unit is mounted at least 100 mm away from any adjacent
structuresorequipment.Iftheserequirements are notmet,theheatgeneratedbytheFP
unit's internal components may cause the unit to fail to meet UL/c-UL standard
requirements.
UL1604Conditions ofAcceptability andHandlingCautions:
1. Power, input and output (I/O) wiring must be in accordance with Class I,
Division 2 wiring methods-Article 501-4(b) of the National Electrical Code, NFPA
70 within the United States, and in accordance with Section 18-152 of the Canadian
ElectricalCodefor units installedwithinCanada.
2. Suitable for use in Class I, Division 2, Groups A, B, C and D, Hazardous Locations.
3. WARNING:Explosionhazard-substitutionofcomponentsmayimpairsuitabilityfor
Class I, Division 2.
4. WARNING: Explosion hazard - when in hazardous locations, turn power OFF before
replacing or wiring modules.
5. WARNING: Explosion hazard - do not disconnect equipment unless power has been
switched OFF, or the area is known to be non-hazardous.
CE Marking Notes
The FP2600-T41-24V is a CE marked product that conforms to EMC directives
EN55011 class A and EN61000-6-2.
*For detailed CE marking information, please contact your local FP distributor.

12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
12345678901234567890123456789012
1-1 Connecting the FP to a PC
SIO Interface Cable (5m)
(FP61V-IS00-O)
(StraightCable:Dsub9-pinfemale)
AnalogRGBInterfaceCable
(FP-CV00<2.5m>,FP-CV01<5m>)
(VGAstandard:Dsub15-pinmale)
1-1
FP2600-T41 User Manual
The following diagram illustrates the connection between the FP unit and a PC.
Chapter 1
Introduction
1. Connecting the FP to a PC
2. Optional Equipment
FP2600-T41 unit
13
2
23
1
B type
A type
PersonalComputer
(PC)
USBInterface Cable (5m)
(FP-US00)
(A-B type Cable)

Introduction
1-2 FP2600-T41 User Manual
1-2 Optional Equipment
AlloptionalitemslistedbelowareproductsofDigitalElectronicsCorporation.
Model Description
SIO Cable FP61V-IS00-O
Serial interface cable (5m) used for touch
panel data transmission between the host
and the FP or command transmission to
the FP. This is a straight Dsub9 pin
female cable.
RGB Cable FP-CV00
FP-CV01
Analog RGB interface cable when image
signal is output to the FP from the host.
VGA specifications (Dsub15 pin male)
FP-CV00 (2.5m), FP-CV01 (5m)
USB Cable FP-US00
USB interface cable (5m) used for touch
panel data transmission between the host
and the FP or command transmission to
the FP.
A-B type cable.
Backlight
Bulbs PS600-BU00 Replacement Backlight bulbs .
Installation
Brackets GP070-AT01 Metal installation brackets for FP2600-T41
Rubber
Gasket GP-WP10-MS Replacement rubber gasket, used when
installing the FP. Same as the FP's
original gasket.
Cover
Sheet
(Hard type) PSL-DF00
Provides disposable screen protection from
dust and other elements. The touch panel
can be used with the Cover Sheet attached
(5 sheets / set)
Mouse
Emulator V2 PL-TD000 Mouse Emulator software for FP.*
Item
Interface
Maintenance
Parts
Optional
Parts
*OperationenvironmentisWindows®95,WindowsNT®4.0,Windows®98,Windows®2000.
WhenyouusePL-TD000,hardwaresettingscannotbeautomaticallydetected.
As a result, select the FP unit's currently connected COM Port, and enter the
settingsgivenintheFPmanualforthe Allocated I/O address and Interrupt.

123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
123456789012345678901234567890121
Chapter 2
Specifications
1. General Specifications 4. Cable Diagrams
2. Functional Specifications 5. Names and Functions of FP Parts
3. Interface Specifications 6. Flat Panel (FP) Dimensions
FP2600-T41 User Manual
2-1-2 Environment Specifications
2-1
*1 (See the next page's note)
2-1 General Specifications (For DC24V)
2-1-1 Electrical Specifications
DCV24V (FP2600-T41)
Operating Temperature 0oCto50oC
StorageTemperature -10oCto60 oC
Humidity 30to85%RH(non-condensing)
VibrationEndurance 19.8m/s2-10to25Hz(X,Y,Zdirections-30minuteseach)
NoiseImmunity Noisevoltage: 1200Vp-p
Pulselength:1µs
Rise time(rise/fall):1ns
PollutionLevel Notimmunetocorrosivegas
Grounding Lessthan100Ω,oryourcountry'sapplicablestandard
Protection*1 Equivalentto IP65f(JEM1030)
Rated Voltage DC24V
RatedVoltageRange DC19.2VtoDC28.8V
PowerConsumption 50Worless
In-Rush Current 30Aorless
VoltageEndurance AC1000V20mAfor1minute
(betweenchargingand FG terminals)
Insulation Resistance 10MΩorhigheratDC500V
(betweenchargingand FG terminals)

FP2600-T41 User Manual
Specifications
2-2
2-1-3 Structural Specifications
The front face of the FP unit, installed in a solid panel, has been tested using
conditions equivalent to the standard shown in the specification . Even though
the FP unit’s level of resistance is equivalent to the standard, oils that should
have no effect on the FP can possibly harm the unit. This can occur in areas
where either vaporized oils are present, or where low viscosity cutting oils are
allowed to adhere to the unit for long periods of time. If the FP’s front face
protection sheet becomes peeled off, these conditions can lead to the ingress of
oil into the FP and separate protection measures are suggested. Also, if non-
approved oils are present, it may cause deformation or corrosion of the front
panel’s plastic cover. Therefore, prior to installing the FP be sure to confirm the
type of conditions that will be present in the FP’s operating environment.
If the installation gasket is used for a long period of time, or if the unit and its
gasket are removed from the panel, the original level of the protection cannot be
guaranteed. To maintain the original protection level, you need to replace the
installation gasket regularly.
*1 (Continued from previous page)
DC24V (FP2600-T41)
ExternalDimensions 317Wx243Hx58Dmm
Weight 3.5kgorless
CoolingSystem Naturalaircirculation

FP2600-T41 User Manual
Specifications
2-3
2-2 Functional Specifications (For DC24 V )
*1 Thebrightness at centralpart of thescreen whendisplayingall white.
*2 2.5 times decreased brightness may be the life span, but this value is only for
reference and not a guaranteed value.
DisplayMedia TFT Active matrix color LCD
DisplaySize 31cm (type 12.1)Opposite angle
DisplayArea(mm) 246.0W×184.5H
Resolution 800(H)×600(V)pixels(1pixel=R+G+Bpixel)
DisplayColors 262,144colors(R/G/BSixbitseach)
Brightness 200cd/m2(typ)*1
DotPitch(mm) 0.33H×0.33W
Resolution: 1024×1024
Method: Resistive Film (Analog)
DisplayMode
SVGAgraphic &Textmode
800×600,640×480,640×400,640×350,720×400,720
×350modedisplayavailable.
However,with350pixels,400pixels,including50
pixelsatthetopandbottom willbe enlargedand
displayed as680pixels(1.5times).
AnalogRGBInterface
SIO Interface(touch Interface)
USB Interface(touch Interface)
Backlight Backlightcanbe changed. Lifetime:50,000hourswhen continuouslylit(*2)at
25oC.
Interfaces
TouchPanel

FP2600-T41 User Manual
Specifications
2-4
2-3-1 Analog RGB Interface
2-3 Interface Specifications (For DC24V)
Inputsignal type Analog RGB
Input signal characteristic Image signal: analog RGB
Synchronous signal: TTL level, negative true or
positive true
Scanning type: non-interlace
Setting by OSD (On Screen
Display) Contrast Adjustment Sub Contrast Adjustment
Brightness Adjustment
Horizontal Display Position Adjustment
Vertical Display Position Adjustment
Horizontal Adjustment
Phase Adjustment
Dimmer Adjustment
Default Setting (All Clear Function)
Size H Sync. V Sync. Dot Clock Range
800 X 600 35.156±1 KHz 56±1 Hz 36.000MHz±1%
800 X 600 37.879±1 KHz 60±1 Hz 40.000MHz±1%
640 X 480 31.469±1 KHz 60±1 Hz 25.175MHz±1%
640 X 480 35.000±1 KHz 66±1 Hz 30.240MHz±1%
640 X 480 37.861±1 KHz 72±1 Hz 31.500MHz±1%
640 X 400 24.827±1 KHz 56±1 Hz 21.053MHz±1%
640 X 400 31.469±1 KHz 70±1 Hz 25.175MHz±1%
640 X 350 31.469±1 KHz 70±1 Hz 25.175MHz±1%
720 X 400 31.469±1 KHz 70±1 Hz 28.322MHz±1%
720 X 350 31.469±1 KHz 70±1 Hz 28.322MHz±1%
• Withvertical350pixels,400pixels, including 50pixelsatthetopand
at the bottom of the screen will be enlarged and displayed at 600
pixels(1.5times).

FP2600-T41 User Manual
Specifications
2-5
Pin
No. Signal Name Condition Pin Location
1 Analog R R signal input
2 Analog G G signal input
3 Analog B B signal input
4 Reserved NC (spare for input)
5 Digital grounding Digital signal GND
6 Return R R signal GND
7 Return G G signal GND
8 Return B B signal GND
9 Reserved NC (spare for input)
10 Digital grounding Digital signal GND
11 Reserved NC (spare for input)
12 Reserved NC (spare for input)
13 H. SYNC Horizontal synchronous
signal input
14 V. SYNC Vertical synchronous
signal input
15 Reserved NC (spare for input)
Pin Assignments and Signal Names for Analog RGB
Connector: MiniDsub15pintype
Connectorsetscrew: Inch type (4-40)
11
15
1
5

FP2600-T41 User Manual
Specifications
2-6
Pin
No. Signal Name Condition Pin Location
1 CD Carrier Detect (FP->Host)
2 RD Receive Data (FP->Host)
3 SD Send Data (FP<-Host)
4 DTR Data Terminal Ready (FP<-Host)
5 GND Ground
6 DSR Data Set Ready (FP->Host)
7 RS Request to Send (FP<-Host)
8 CS Clear to Send (FP->Host)
9 NC No connection
Concerning Signal Names
Signalnamesusedfor the serial interface onFPunitsaredesignedto match
the pin order used on most PC serial interfaces, so that a straight cable can
be used to connect the two. Therefore, connect each pin's signal to the same
signalname on thePC side.
For example, pin #2 'RD' should be connected to the 'RD' input terminal on
the PC's connector.
Refer to section "2-4 Cable Diagrams" for each signal's direction.
2-3-2 Serial Interface
Pin Assignments and Signal Names for Serial Interface
Connector: Dsub9pinfemale
Connector set screw: Inch type (4-40)
Serial Interface
Baud rate: 9600 bps
Data length: 8 bits
Parity: none
Stop bit: 1
6
9
1
5

FP2600-T41 User Manual
Specifications
2-7
2-3-3 USB Interface
Pin Assignments and Signal Names for USB Interface
Communication Low speed Device
Connector: Btypeconnector
Pin
NO. Signal Name Condition Pin Location
1 USB1-5V +5VIN
2 USBD1(-) USBdata(-)
3 USBD1(+) USBdata(+)
4 GND Ground
12
43