Profile ADAGIO PAC-312 User manual

ADAGIO SET – Cordless doorbel set UK - 1
PAC-312 / PAC-314 / PAC-316 / PAC-318
Thank you for purchasing this Profile product. Please
note: It is important that you read this manual before
using the product. And be sure to save this manual for
possible use later.
The cordless doorbell consists of 2 separate
components:
1. Push-button unit (transmitter)
2. Bell unit (receiver)
These items are completely independent of each other
and require no wiring.
When the push-button is pressed in, a signal is sent to
the bell, whereupon the bell is activated. Since it has a
range of up to 100 meters (in open spaces) you can use
the bell virtually anywhere in the house, workshop,
office, set it up in the garden or just carry it with you.
Battery installation
Push-button unit
1. The push-button unit works using 1 x 3v
(CR2032) lithium battery (included).
2. The lithium battery is already installed. Open
the push-button and remove the insulator
strip.
3. Snap the rear side back into position, and the
push-button is ready for use.
To replace the battery:
1. Open up the push-button unit.
2. Remove the metal plate using a screwdriver.
3. Place a 3v battery (CR2032) in the battery
compartment, making sure the positive
terminal (+) is uppermost.
Bell unit
1. Slide the rear cover open.
2. Place 2 AA alkaline batteries into the battery
compartment.
3. The bell unit will produce a two-tone signal,
indicating that it is ready to read a digital code
(see channel selection).
4. Slide the cover firmly back into place; the bell
is now ready for use.
Installation
Push-button unit
Use the two small holes on the
rear of the push-button to mark
the position for securing in
place. Drill small holes and
mount the push-button in
position with screws (self-
tapping 3 x 16mm, included) or
use the double-sided adhesive
tape (included).
Important: If you secure the
push-button onto a metal
upper surface or PVC type of
door (with metal), its maximum range of transmission
will be greatly reduced.
Bell unit
This bell can be used as a portable device - or fixed into
position. On the reverse side, there are two suspension
slots, with which the bell can be hung up using a screw,
and can easily be taken down again. Drill a small hole
and fix a rawlplug in place. Mount the hook (included)
onto the wall using a screw. The bell unit can hung up
safely in this way.
Choice of bell tone
The bell-tone selector button is inside the push-button
unit, below letter “S”. Press the button once to hear the
bell tone already set. Press again to hear and select the
next tune.
1. Long Westminster chime 2. Ding-Dong
3. Telephone ring 4. Circus theme
5. Banjo on my knee 6. Twinkle-twinkle
7. It’s a small world 8. Barking dog
Optionally: It is possible to install an extra push-button
by your back door. By applying the procedure given
above, each push-button can produce a different tune.
Channel selection
The unit is supplied with a pre-set radio frequency. If by
chance the bell should sound for no apparent reason,
it's possible that another device nearby is using the same
frequency. To get round this problem, you can change
the frequency of the push-button and bell.
1. remove the cover behind the push-button.
2. To program or change: remove the batteries
from the bell unit for at least 30 seconds to
prime the memory.
3. place the batteries back into position within.
Press the push-button after the two-tone signal
sound (with a second press of the button if
need be) to confirm the new code. Do this
within 1 minute. Don’t use any other cordless
products for the next 5 minutes.
4. Test for correct operation.
Volume selection
There is a volume-selector button inside the bell unit.
Slide the button to ‘high’ (85 dB) or ‘low’ (82 dB) to set
at the desired bell volume.
Trouble-shooting and tips
Problem: Bell rings, but LEDs fail to light up
Possible cause: - The bell is out-of-range (max.
100m in open spaces)
Possible solution: - Move the bell within range
- Reprogram the channel (see
channel selection)
Problem: Bell does not ring, nor do the LEDs
light up
Possible cause: - Push-button battery is flat

ADAGIO SET – Cordless doorbel set UK - 2
PAC-312 / PAC-314 / PAC-316 / PAC-318
- Batteries are not correctly installed
in the push-button
Possible solution: - Replace battery
- Reinstall the batteries in their
correct positions (see battery
installation for push-button unit)
Warning
1. Do not fasten the push-button onto a metal
upper surface or PVC type of door. This
restricts their range.
2. Do not expose the bell unit to direct rain,
splashing water or direct sunlight, and do not
immerse the unit in water.
3. Do not drop the bell or push-button, or subject
them to severe insults.
4. Do not expose either unit to high
temperatures, nor place them close to sources
of heat.
5. Never combine different types of batteries, nor
use old and new batteries together.
6. Always use alkaline batteries: they will last
longer and there is less risk of leakage.
7. If the bell will be out of use for a prolonged
period, remove the batteries.
8. The bell unit is suitable for use indoors only.
9. Please dispose of old or faulty batteries in an
environmentally-friendly manner, in
accordance with applicable laws.
10. Ensure that no naked flames, e.g. candles, are
placed near the bell.
11. Replace batteries using only those
recommended by the manufacturer.
GENERAL specifications
•Range of 100m (in open spaces)
•8 tunes
•Push-button: 1 x CR2032 lithium battery
(included)
•Push-button (IP44) is watertight against water
splashes
•Operating frequency: 433.92 MHz.
•2 volume settings
•Gong: 2 x AA batteries (not included).
Declaration of conformity
ELTRA NV, Pachtgoedstraat 2, 9140 Temse, Belgium, hereby
declares that the product Adagio Set comprising:
Transmitter: PAC-312T / PAC-314T / PAC-316T / PAC-318T
Receiver : PAC-312R / PAC-314R / PAC-316R / PAC-318R
(Transmitters en receivers work identically)
satisfies all essential requirements and other applicable
stipulations of the LVD and EMC guideline 89/336/EEC en
1995/5/EEC and has been tested against the following
standards:
EN 300 220-1/-2 V2.1.1
EN 301 489-1/-3 V1.4.1-V1.6.1
EN 60950-1:2006
IEC 62080:2001,EN 60065:2002
The original declaration of conformity can be called up on
www.profileDIY.com
Terms of the guarantee
The guarantee period for PAC-312 / PAC-314 / PAC-316 /
PAC-318 is 2 years from the date of purchase. During the
guarantee period, ELTRA NV will remedy any defect that is
attributable to faulty materials or manufacture. ELTRA NV may
elect either to replace or repair the defective appliance.
ELTRA NV is under no obligation to repair or replace an
appliance where a defect arises due to damage, inappropriate
use, modifications or alterations made or occurring after the
purchase date.
Return the faulty appliance, together with proof of purchase, to
the shop from which it was purchased. Always include a note
describing the problem.
Damage
Under no circumstances can ELTRA NV be held liable for
damage of any kind where the appliance has not been
installed in accordance with the instructions provided, nor for
damage resulting from unforeseeable circumstances such as
natural disaster, lightning strike, etc. All such consequential
costs are therefore for the exclusive account of the purchaser
and are not covered under the terms of the guarantee.