Progress Lighting AirPro P250093 User manual

P250093
Ceiling Fan Installation Manual
93161625_A

Date Purchased
Store Purchased
Model No.
Serial No.
Vendor No.
UPC
126900
P250093
Limited Lifetime Warranty
Progress Lighting fan motors are warranted to the original purchaser to be free of electrical and/or mechanical defects for so
long as the original purchaser owns the fan. Pull chain switches, reverse switches, capacitors and metal finishes are warranted to
be free from defects in materials or workmanship for a period of 1 year from the date of purchase. Warping of wooden or plastic
blades is not covered by this warranty nor is corrosion and/or deterioration of any finishes for fans installed within ten miles of
any sea coast. Extended warranties for ENERGY STAR®qualified products may apply.
Progress Lighting ceiling fans with built-in LED light sources, when properly installed and under normal conditions of use, are
warranted to be free from defects in material and workmanship which cause the light sources to fail to operate in accordance
with the specifications for (i) five (5) years from the date of purchase on the LED Light modules and electrical components for
fans used in single family residences, and (ii) three (3) years from the date of purchase on the LED Light modules and electrical
components for fans used in multi-family or commercial applications. LED bulbs supplied by Progress Lighting carry no
warranty other than manufacturer’s warranty. Non-LED bulbs carry no warranty.
With proof of purchase, the original purchaser may return the defective fan to the place of purchase during the first 30 days for
replacement. After 30 days, the original purchaser MUST contact Progress Lighting at [phone] for repair or replacement
which shall be determined in Progress Lighting’s sole discretion and shall be purchaser’s sole and exclusive remedy.
Labor and Shipping Excluded. This warranty does not cover any costs or fees associated with the labor (including, but not
limited to, electrician’s fees) required to install, remove, or replace a fan or any fan parts.
This warranty shall not apply to any loss or damage resulting from (i) normal wear and tear or alteration, misuse, abuse or
neglect, or (ii) improper installation, operation, repair or maintenance by original purchaser or a third party, including without
limitation improper voltage supply or power surge, use of improper parts or accessories, unauthorized repair (made or
attempted) or failure to provide maintenance to the fan.
THE FOREGOING WARRANTIES STATE PROGRESS LIGHTING’S ENTIRE WARRANTY OBLIGATION AND
ORIGINAL PURCHASER’S SOLE AND EXCLUSIVE REMEDY RELATED TO SUCH PRODUCTS. PROGRESS
LIGHTING IS NOT RESPONSIBLE FOR DAMAGES (INCLUDING INDIRECT, SPECIAL, INCIDENTIAL OR
CONSEQUENTIAL), DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY,
BREACH OF CONTRACT, OR OTHERWISE. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER WARRANTIES,
WHETHER EXPRESSED OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE OR NONINFRINGEMENT.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or
consequential damages, so the above limitations and exclusions may not apply to you. This warranty gives you specific rights
and you may have other rights which vary from state to state.
UPC 785247266746

Table of Contents
Safety Rules.....................................................................................................................................................................................
Unpacking Your Fan .......................................................................................................................................................................
Installing Your Fan .........................................................................................................................................................................
Operating Your Transmitter..............................................................................................
.............................................................
1.
2.
3.
9.
Care of Your Fan .............................................................................................................. ...........................................................
Troubleshooting ............................................................................................................................................................................
Specifications ................................................................................................................................................................................
11.
12.
10.

1. Safety Rules
1. To reduce the risk of electric shock, ensure electricity has been turned off
at the circuit breaker or fuse boxbefore beginning.
2. All wiring must be in accordance with the National Electrical Code and
localelectrical codes. Electricalinstallation should be performed by a
qualified licensed electrician.
3.WARNING: To reduce the risk of electrical shock and fire, do not use
this fan with any solid-state fan speed control device.
4. WARNING: To reduce the risk of fire, electric shock,orpersonalinjury,
mount to outlet box marked "Acceptable for Fan Support of 15.9 kg (35 lbs.)
Or Less"andusemounting screws provided withthe outlet box. Most outlet
boxescommonly used for thesupport of light fixtures are not acceptable for
fan support andmayneed to be replaced. Due to the complexity of the
installation of this fan, a qualified licensed electrician is strongly
recommended.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted and
capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less.
Use only UL-listed outlet boxes marked FOR FAN SUPPORT.
6. The fan must be mounted with a minimum of 7 ft (2.1m) clearance from
the trailing edge of the blades to the floor.
7. To operate the reverse function on this fan, press the reversing button while
the fan is running.
8. Avoid placing objects in the path of the blades.
9. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
10. Do not use water or detergents when cleaning the fan or fan blades. A
dry dust cloth or lightlydampenedcloth will be suitable for most
cleaning.
11.After making electrical connections, spliced conductors should be
turned upward and pushed carefully up into the outletbox. The wires
should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the outlet box.
12.Electrical diagrams are for reference only. Light kits that are not packed
with the fan mustbeULListed and marked suitable for use withthe
model fan you are installing. Switches must be UL General Use
Switches. Refer to the Instructions packaged withthe light kits
NOTE
READ AND SAVE ALL INSTRUCTIONS!
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.

Unpacking Your Fan 2.
13
a b
Unpack your fan and check the contents. You should have the following items:
1.Fan blades (3)
2.Hanger bracket
3.Ball/downrod assembly
4.Canopy
5.Decorative cover
6.Coupling cover
7.Fan motor assembly
8.Switch housing
9.Light kit assembly
10.Acrylic shade
11.LED bulb (2)
12.Wall control with 3 wire nuts
13.Loose parts bag containing:
a.Blade screws (10)
b.Mounting hardware
Wire nuts (4)
1
2
3
4
6
5
8
9
10
712
11
X3
0
O
-

Tools Required
Phillips screw driver, straight slot screw driver,
adjustable wrench, step ladder, and wire cutters.
Mounting Options
If there isn't an existing UL listed mounting box,
then read the following instructions. Disconnect
the power by removing fuses or turning off
circuit breakers.
Secure the outlet box directly to the building
structure. Useappropriate fasteners and building
materials. The outlet box and its support must be
able to fully support the moving weight of the
fan (at least 35 lbs). Do not use plastic outlet
boxes.
3. Installing Your Fan
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK, OR OTHER PERSONAL INJURY,
MOUNT FAN ONLY TO AN OUTLET BOX
MARKED ACCEPTABLE FOR FAN SUPPORT
AND USE THE MOUNTING SCREWS
PROVIDED WITH THE OUTLET BOX. OUTLET
BOXES COMMONLY USED FOR THE
SUPPORT OF LIGHTING FIXTURES MAY NOT
BE ACCEPTABLE FOR FAN SUPPORT AND
MAY NEED TO BE REPLACED. CONSULT A
QUALIFIED ELECTRICIAN IF IN DOUBT.
Figure 1
Outlet box
Figure 2
Outlet box
Figure 3
Angled ceiling
maximum
25 angle
Recessed
outlet box
Provide strong support
Ceiling
hanger
bracket
Figure 4
Outlet box
Note: You may need a longer downrod to
maintain proper blade clearance when installing
on a steep, sloped ceiling.
To hang your fan where there is an existing
fixture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at your Progress Lighting Retailer).

4.
Hanging the Fan
WARNING
FAILURE TO PROPERLY INSTALL
LOCK PIN AS NOTED IN STEP 5
COULD RESULT IN FAN LOOSENING AND
POSSIBLY FALLING.
Ceiling hanger
bracket
UL Listed
electrical box
Washers
Mounting screws
(supplied with
electrical box)
120V wires
Figure 5
Hanger pin
Lock
pin
Hanger ball
Figure 6
Downrod/ball
assembly
Motor
assembly
Downrod
Canopy
Decorative cover
Coupling cover
Hanger pin
Lock pin
Figure 7
pin through the hole near the end of the hanger pin
until it snaps into its locked position, and tighten
set screws as shown in Fig.7. Cut off excess
fixture wires leaving approximately 6 to 9 inches
above top of hanger ball/downrod assembly.
Step 5. Align the holes at the bottom of the
downrod with the holes in the collar on top of the
motor housing (Fig. 7). Carefully insert the
hanger pin through the holes in the collar and
downrod. Be careful not to jam the pin against
the wiring inside the downrod. Insert the lock
REMEMBER to turn off the power. Follow the
steps below to hang your fan properly:
Step 1. Pass the 120-volt supply wires through
the center hole in the ceiling hanger bracket as
shown in Fig. 5.
Step 2. Secure the hanger bracket to the ceiling
outlet box with the screws and washers provided
with your outlet box.
Step 3. Remove the hanger pin, lock pin and set
screws from the top of the motor assembly. (Fig. 6)
Step 4. Route wires exiting from the top of the fan
motor through the coupling cover, decorative
cover, canopy and then through the downrod.
(Fig. 7)

5.
Step 6. Carefully lift the assembly and rest the
hanger ball of downrod assembly on the hanger
bracket attached to the outlet box. Be sure the
groove in the hanger ball is lined up with the tab
on the hanger bracket. (Fig.8) WARNING:To avoid possible electrical shock,
be sure electricity is turned off at the main fuse
box before wiring.
WARNING: If you feel you do not have enough
electrical wiring knowledge or experience, have
your fan installed by a licensed electrician.
Step 1. Motor to wall control electrical
connections: Connect the white (neutral) wire
from the ceiling to the white wire from the motor.
Connect the black wire from the motor to the
black wire from the wall control. Connect the blue
wire from the fan to the blue wire from the wall
control. (Fig.9)
Step 2. Motor to house supply wires electrical
connections: Connect the black (hot) wire from
the ceiling to the black wire and blue wire from
the motor. (Fig.9)
Secure all wire connections with the plastic wire
nuts provided.
Make the Electric
Connections
Figure 8
OK NO
Hanger
ball Tab
Groove
Hanger
bracket
Figure 9
-
O
AC IN NWHITE
BLACK BLACK
BLUEBLUE
GREEN
GREEN
GREENGREEN
AC IN LAC IN L
BLACK
0

6.
Step 1. Tuck connections neatly into ceiling
outlet box.
Step 2. Slide the canopy up to mounting bracket
and place the key hole on the canopy over the
screw on the mounting bracket, turn canopy until
it locks in place at the narrow section of the key
holes. (Fig. 10)
Step 3. Align the circular hole on canopy with the
remaining hole on the mounting bracket, secure
by tightening the two set screws. Note: Adjust the
canopy screws as necessary until the canopy and
canopy cover are snug.
Step 5. Attach the blade screws and tighten them.
Repeat this step for the 2 remaining blades.
Tighten the screws securely. (Figure 12)
Step 4. Attach the blades to the blade holder ring.
(Figure 11)
Step 6. Remove one of the mounting screws on
mounting plate of motor assembly, then loosen
the other two. (Figure 13)
Finishing the Installation
WARNING
Make sure the notch on the hanging bracket properly
sits in the groove in the hanger ball before attaching
the canopy to the bracket by turning the housing until
it drops into place.
Blade
Blade holder ring
Blade screw
Switch housing
Figure 11
Figure 12
Figure 10
Mounting
screw
Figure 13
Figure 14

7.
Step 7. Attach the switch housing to the
mounting plate on the motor assembly by placing
the keyhole slots from the switch housing onto the
two protruding mounting screws heads.
Step 8. Remove one of three switch housing
screws on the switch housing and keep for later
use, then loosen the other two.
Step 10. Insert two MAXIMUM 6W E26 LED
bulbs (included) into lamp holders. Dry your
hands before installing bulbs. Keeping the bulbs
clean is important as useful lifetime of a dirty
bulb could be shorter than a clean bulb.
Step 11. Secure the shade to switch housing by
twisting in a clockwise direction. Do not
over-tighten.
Step 9. Connect the 2-pin connectors from the
light kit to the 2-pin connectors from the motor
assembly. Attach the light kit to switch housing
using the two key slots in the light kit. Replace the
screw previously removed on step 8. Tighten all
switch housing screws securely.
Figure 15
Switch housing
screw
Light kit
asscmbly
LED Bulb
Acrylic shade
Figure 16
Figure 17
Figure 18