Project Source 51-K814-PS-BN User manual

1
ATTACH YOUR RECEIPT HERE
Serial Number _______________ Purchase Date ______________
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-389-8827, 8 a.m. - 8 p.m., EST, Monday - Friday.
ITEMS #0831710
#0831709
PULL-DOWN
KITCHEN FAUCET
MODELS #51-K814-PS-BN
#51-K814-PS-WH
Français / Español p. 9
AB16906
®
Project Source® is a registered trademark
of LF, LLC. All rights reserved.

2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
AFaucet body assembly 1
B Escutcheon 1
C Gasket 1
D Weight 1
HARDWARE CONTENTS (not shown actual size)
AA BB CC
Lock
Nut Metal Washer Hex Bolt
Qty. 1 Qty. 1 Qty. 2
B
C
D
A

3
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
CAUTION
• If you solder the joints during installation of the faucet, the seats, cartridges, and washers must be
removed before using a ame or the warranty will be voided on these parts.
• Cover the sink drain to avoid losing parts.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water supply lines.
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package
contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble
the product.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, Groove Joint Pliers, Pipe Wrench,
Phillips Screwdriver, and Supply Lines
Installations may vary depending on how the previous faucet was installed. Supplies necessary
for the installation of the faucet are not all included; however, they are available wherever plumbing
supplies are sold.
Prior to beginning installation, turn off the hot and cold water lines, then turn on the old faucet to
release built-up pressure. When installing the new faucet, hand tighten the connector nuts. DO
NOT OVERTIGHTEN. Connections that are too tight will reduce the integrity of the system.
PRODUCT SPECIFICATIONS
SPECIFICATIONS SPECIFICATIONS
Max. ow rate: 1.8 GPM (6,8 LPM) at 60 PSI Total weight of item: 4.87 lbs.
ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25%
weighted average lead content on wetted
surfaces
Brushed nickel and white nishes
Ceramic cartridges

4
ASSEMBLY INSTRUCTIONS
1. Turn off water at the supply valve at the main water supply, disconnect
the supply lines, and remove old faucet body.
Clean and dry surface area where new faucet will be mounted.
1
2. Before installation, remove the quick connector (2.1) from the free end of
the hose (2.2) by unscrewing it in a counterclockwise direction. Unscrew
the locking nut (2.3) and remove the metal washer (2.4).
2
3. Optional Flange Installation
Install faucet with attached ange (3.5). Retract the hose (3.1) up through the
faucet body assembly (A) until the end of the hose (3.1) is ush with the bottom
of the shank (3.2). Do not pull the end of the hose (3.1) past the shank (3.2).
Insert the faucet body assembly (A) through the hole in the sink (3.3). Once
this step is complete continue to step 6.
NOTE: Do not feed the hose (3.1) back through the spout (3.4) until step 7.
3
3.1
3.2
3.4
3.3
A
3.5
4. Optional Escutcheon Installation
Remove the ange and place the escutcheon with gasket (B and C) on the
bottom of the new faucet body assembly.
4
5. Retract the hose (5.1) up through the faucet body assembly (A) until the end of
the hose (5.1) is ush with the bottom of the shank (5.2). Do not pull the end of
the hose (5.1) past the past the shank (5.2). Insert the faucet body assembly
(A) through the hole in the sink (5.3).
NOTE: Do not feed the hose (5.1) back through the spout (5.4) until step 7.
5
5.1
5.2
5.4
5.3
A
2.1
2.2
2.3
2.4
B
C

5
ASSEMBLY INSTRUCTIONS
6. Install the metal washer (BB) onto the threaded shank (6.1). Thread the
locking nut (AA) onto the shank (6.1). Lock the locking nut (AA) into position
by tightening the hex bolts (CC). Do not overtighten.
Hardware Used
BB Metal washer x 1
AA Lock nut x 1
CC
Hex bolt x 2
6
7. After inserting the hose (7.1) through the hole in the sink surface, retract the
hose (7.1) back down, and reattach the quick connector (7.2) by screwing it onto
the end of the hose (7.3) in a clockwise motion. Hand tighten only.
7
8. Push the quick connector (8.1) rmly upward and attach it to the receiving
block (8.2). Pull down moderately to ensure the connection has been made.
If it is necessary to remove the quick connector (8.1), squeeze the tabs on the
hose (8.3) and then pull down to disconnect. After connecting the hose (8.3),
install the weight (C) at the point of the hose marked "weight here" (8.4).
8
Weight
Here
Weight
Here
9. Make Connections to the Water Lines
(9.1) Use 1/2 in. IPS faucet supply lines or (9.2) use coupling nuts (not
supplied) with (9.3) ball-nose risers (not included).
Turn water supply or shut-off valve back on and check for leaks. If leaks
occur, gently tighten the faucet connections.
9
9.1
9.3
9.2
AA
BB
6.1
7.1
7.2
CC
7.3
CC
8.4
8.2
8.3
8.1