Promet PS610/E36 User manual

Safe Digital Lock PS610/E36 USER MANUAL
www.promet-safe.com
Ver. 1/3 25.02.2019г.
SAFE DIGITAL LOCK
PS610/E36
USER MANUAL
1Main Components
Fig.1.1
1 –Case, 2 –Keypad, 3 –Green LED [G], 4 –Red LED
[R], 5 –Battery box
2Definitions
2.1 Master Code [PIN1]
A set of numbers (from 6 to 8 digits) which opens
the lock and allows to operate the settings.
Before using the safe, please change the factory
Master code (see par.4.1). It is strongly recommended
to keep the master code safe from unauthorized
people.
No easily guessed numbers (birthdays, house and
phone numbers, etc.) or simple codes (1, 2, 3, 4, 5, 6)
shall be chosen for the code.
Factory Master Code:
1–2–3–4–5–6
2.2 User Code [PIN2]
A set of numbers from 6 to 8 digits which opens
the lock and has limited functions to change the
settings.
The lock with default factory settings does not have
the User code. Please see par.4.2 to set the User
code.
2.3 Signals
[G]1Short single acoustic signal with single
green LED flash (3) –confirmation of the button
pressing on the keypad.
[G]2Short double acoustic signal with double
green LED flash (3) –confirmation of successfully
finished operation.
[R]-- Long single acoustic signal with single red
LED flash (4) –error message on the user’s actions.
[R]5Short acoustic signal sounds 5 times with 5
red LED flashes (4) –low battery message. Please see
par.7.1 how to change the battery.
3Main Functions
3.1 Opening the Lock
3.1.1 Opening with the Factory Master code
[ON][1][2][3][4][5][6][Enter]
3.1.2 Opening with the Master Code
[ON][PIN1][Enter]
3.1.3 Opening with the User Code
[ON][PIN2][Enter]
If the code is right, there will be a green LED
flash and it will be possible to open the door within 5
seconds by turning the door hand clockwise.
If you enter a wrong code three times in a row, the
lock will be blocked for 5 minutes. This will be
indicated via periodical red LED flashes.
3.2 Closing the Lock
Close the door and turn the door hand anti-
clockwise until it stops.
4Service Functions
It is strongly recommended to change the settings of
the lock with the door opened.
After code changing, the lock shall be tested several
times with the secure storage unit’s door in open
state.
The service functions will be unavailable in case of
low power supply which is indicated by the signals,
please refer to par.2.3, [R]5.
4.1 Changing the Master Code [PIN1]
[ON] [Enter] [1] [Enter] [PIN1] [Enter]
[new PIN1][Enter][repeat new PIN1][Enter]
Checking the new Master code:
[ON][new PIN1][Enter]
4.2 Setting and changing the User Code [PIN2]
with the Master Code [PIN1]
Before changing the User Code [PIN2] default factory
setting of Master code [PIN1] has to be changed (see
par.4.1).
[ON] [Enter] [2] [Enter]
[1-9 (user number)] [Enter] [PIN1] [Enter]
[new PIN2] [Enter]
[repeat new PIN2] [Enter]
Checking the new User code:

Safe Digital Lock PS610/E36 USER MANUAL
www.promet-safe.com
Ver. 1/3 25.02.2019г.
[ON][new PIN2][Enter]
4.3 Changing the User Code [PIN2] without the
Master Code
[ON] [Enter] [3] [Enter]
[1-9 (user number)] [Enter] [PIN2] [Enter]
[new PIN2] [Enter]
[repeat new PIN2] [Enter]
Checking the new User Code:
[ON][new PIN2][Enter]
4.4 Deleting the User Code
[ON][Enter][0][Enter][1-9 (user number)]
[Enter][PIN1][Enter]
4.5 Switching off/switching on the sound
[ON][Enter][5][Enter][PIN1][Enter]
5Time Delay Function
5.1 Switching on the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[01-99 –delay time] [1-9 –time for
opening] [Enter]
E.g.: 092 –9 minutes is the delay time, 2 minutes is
the time for opening
5.2 Opening the Lock with the Time Delay
[ON] [PIN1 or PIN2] [Enter] (Waiting Delay
Time. Acoustic signal will inform about
the end.)[PIN1 or PIN2] [Enter]
Pressing [Enter] during Time Delay leads to an
interruption. Operation has to be started again.
5.3 Switching off the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[000] [Enter]
6Dual Code Function
6.1 Switching on the Dual Code function
Before switching on the function, make sure you have
assigned a User Code [PIN2] see par.4.2.
The Dual Code function has priority over other lock
functions.
[ON] [Enter] [7] [Enter] [PIN1] [Enter]
When press [ON] button, switched on Dual Code
function indicates [  G]2 (see par.2.3).
6.2 Opening with the Dual Code function
[ON][0-9 (user number)][Enter]
[PIN2][Enter]
[0-9 (user number)][Enter]
[PIN3][Enter] –in 1 minute
The User number of Master Code is [0].
After right first Code was entering [PIN2][Enter], for
enter the second Code [PIN3][Enter] there are just 1
minute, that indicates [  G]1 (see par.2.3) every 5
seconds.
6.3 Switching off the Dual Code function
[ON] [Enter] [8] [Enter] [PIN1] [Enter]
7Servicing
7.1 Changing the Battery
The pullout battery box (5) is located on the
inner side of the case (1).
Remove the screw blocking the battery box (see
Fig.7.1).
Squeeze latches and pull the battery box down
(see Fig.7.1).
Fig. 7.1
Disconnect the battery from the contact pads,
placed to the right, as shown in Fig.7.2.
Fig. 7.2
Remove the battery and replace it with a new
one (9V, type 6LF22).
Take the box and screw it back in the reverse
order to their location.