Promet PS310/E31 User manual

Safe Digital Lock PS310/E31 USER MANUAL
www.promet-safe.com
Ver. 1/3 15.02.2019
SAFE DIGITAL LOCK PS310/E31
USER MANUAL
1Main Components
Fig. 1.1
1 –Keypad, 2 –Folding handle, 3 –Green LED [G], 4 –
Red LED [R], 5 –Plastic cover for emergency power
2Definitions
2.1 Master Code [PIN1]
A set of numbers (from 6 to 8 digits) which
opens the lock and allows to operate the settings.
Before using the safe, please change the factory
Master code (see par.4.1). It is strongly
recommended to keep the master code safe from
unauthorized people.
No easily guessed numbers (birthdays, house and
phone numbers, etc.) or simple codes (1, 2, 3, 4, 5,
6) shall be chosen for the coding.
Factory Master Code:
1–2–3–4–5–6
2.2 User Code [PIN2]
A set of numbers from 6 to 8 digits which opens
the lock and has limited functions to change the
settings.
The lock with the default factory settings does not
have the User code. Please see par.4.2 to set the
User code.
2.3 Signals
[G]1Short single acoustic signal with single
green LED flash (3) –confirmation of the button
pressing on the keypad.
[G]2Short double acoustic signal with double
green LED flash (3) –confirmation of successfully
finished operation.
[R]-- Long single acoustic signal with single
red LED flash (4) –error message on the user’s
actions.
[R]5Short acoustic signal sounds 5 times with
5 red LED flashes (4) –low battery message. Please
see par.5.1 how to change the battery.
3Main Functions
3.1 Opening the Lock
3.1.1 Opening with the Factory Master code
[ON][1][2][3][4][5][6][Enter]
3.1.2 Opening with the Master Code
[ON][PIN1][Enter]
3.1.3 Opening with the User Code
[ON][PIN2][Enter]
If the code is right, there will be a green LED
flash and it will be possible to open the door within 5
seconds by turning the handle (2) clockwise.
If you enter a wrong code three times in a row, the
lock will be blocked for 5 minutes. The blocking of the
lock will be indicated periodical red LED flashes.
3.2 Closing the Lock
Close the door and turn the handle (2) anti-
clockwise until it stops.
4Service Functions
It is strongly recommended to change the settings of
the lock with the door opened.
After code changing, the lock shall be tested several
times with the secure storage unit’s door in open
state.
The service functions will be unavailable in case low
power supply which is indicated by the signals,
please refer to par.2.3, [R]5.
4.1 Changing the Master Code [PIN1]
[ON] [Enter] [1] [Enter] [PIN1] [Enter]
[new PIN1] [Enter]
[repeat new PIN1] [Enter]
Checking the new Master code:
[ON][new PIN1][Enter]
4.2 Setting and changing the User Code [PIN2]
with the Master Code [PIN1]
Before changing the User Code [PIN2] default factory
setting of Master code [PIN1] have to be changed
(see par.4.1).
[ON][Enter][2][Enter]
[1-9 (user number)][Enter][PIN1][Enter]
[new PIN2][Enter]
[repeat new PIN2] [Enter]
Checking the new User Code:
[ON][new PIN2][Enter]
4.3 Changing the User Code [PIN2] without the
Master Code
[ON][Enter][3][Enter]
[1-9 (user number)][Enter][PIN2][Enter]

Safe Digital Lock PS310/E31 USER MANUAL
www.promet-safe.com
Ver. 1/3 15.02.2019
[new PIN2][Enter]
[repeat new PIN2] [Enter]
Checking the new User Code:
[ON][new PIN2][Enter]
4.4 Deleting the User Code
[ON][Enter][0][Enter][1-9 (user
number)][Enter][PIN1][Enter]
4.5 Switching off/switching on the sound
[ON][Enter][5][Enter][PIN1][Enter]
5Time Delay Function
5.1 Switching on the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[01-99 –delay time] [1-9 –time for
opening] [Enter]
E.g.: 092 –9 minutes is the delay time, 2 minutes is
the time for opening
5.2 Opening the Lock with the Time Delay
[ON] [PIN1 or PIN2] [Enter] (Waiting
Delay Time. Acoustic signal will inform
about the end.)[PIN1 or PIN2] [Enter]
Pressing [Enter] during Time Delay leads to an
interruption. Operation has to be started again.
5.3 Switching off the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[000] [Enter]
6Dual Code Function
6.1 Switching on the Dual Code function
Before switching on the function, make sure you
have assigned a User Code [PIN2] see par.4.2.
The Dual Code function has priority over other lock
functions.
[ON] [Enter] [7] [Enter] [PIN1] [Enter]
When press [ON] button, switched on Dual Code
function indicates [  G]2 (see par.2.3).
6.2 Opening with the Dual Code function
[ON][0-9 (user number)][Enter]
[PIN2][Enter]
[0-9 (user number)][Enter]
[PIN3][Enter] –in 1 minute
The User number of Master Code is [0].
After right first Code was entering [PIN2][Enter], for
enter the second Code [PIN3][Enter] there are just 1
minute, that indicates [  G]1 (see par.2.3) every 5
seconds.
6.3 Switching off the Dual Code function
[ON] [Enter] [8] [Enter] [PIN1] [Enter]
7Servicing
7.1 Changing the Battery
The battery is located on the inner side of the
door. Depending on the safe model, battery
could be either inside the lock battery
compartment (Fig.5.1a) or in a special pull-out
battery box (Fig.5.1b).
Take out the cover of the battery compartment
of the lock (see Fig. 7.1a. or pull out the box
(see Fig. 7.1b).
Fig. 7.1 a. b.
Install a new battery (9V, type 6LF22).
Take the cover or the box back to their location.
7.2 Opening the lock when the Battery is
Discharged
Take a new battery (9V, type 6LF22).
Take out the plastic cover for emergency power
(5), see Fig. 5.2.
Fig. 7.2
Press the new battery to emergency power pins
and fix it in this position (see Fig.5.3).
Do not make the battery’s contacts to the metal parts
of the lock.
Fig. 7.3
Enter the valid code on the keypad (1).
Disconnect the emergency battery, open the
door and change the discharged battery, see
par. 5.1.