Promet PS600/E36 User manual

Safe Digital Lock PS600/E36 USER MANUAL
www.promet-safe.com
Ver. 3/1 21.02.2017
SAFE DIGITAL LOCK
PS600/E36
USER MANUAL
1Main Components
Fig.1.1
1 –Case
2 –Keypad
3 –Green LED [G]
4 –Red LED [R]
5 –Battery box
2Definitions
2.1 Master Code [PIN1]
A set of numbers (from 6 to 8 digits) which opens
the lock and allows to operate the settings.
Before using the safe, please change the factory
Master code (see par.4.1). It is strongly
recommended to keep the master code safe
from unauthorized people.
No easily guessed numbers (birthdays, house
and phone numbers, etc.) or simple codes (1, 2,
3, 4, 5, 6) shall be chosen for the coding.
Factory Master Code:
1–2–3–4–5–6
2.2 User Code [PIN2]
A set of numbers from 6 to 8 digits which opens
the lock and has limited functions to change the
settings.
The lock with default factory settings does not
have the User code. Please see par.4.2 to set
the User code.
2.3 Signals
[G]1Short single acoustic signal with single
green LED flash (3) –confirmation of the button
pressing on the keypad.
[G]2Short double acoustic signal with double
green LED flash (3) –confirmation of successfully
finished operation.
[R]-- Long single acoustic signal with single red
LED flash (4) –error message on the user’s actions.
[R]5Short acoustic signal sounds 5 times with 5
red LED flashes (4) –low battery message. Please see
par.5.1 how to change the battery.
3Main Functions
3.1 Opening the Lock
3.1.1 Opening with the Factory Master code
[ON][1][2][3][4][5][6][Enter]
3.1.2 Opening with the Master Code
[ON][PIN1][Enter]
3.1.3 Opening with the User Code
[ON][PIN2][Enter]
3.1.4 Opening with the Dual Code
[ON][PIN1][Enter]
[PIN2][Enter] –in 1 minute
After right Master Code was entering
[PIN1][Enter], for enter User Code [PIN2][Enter]
there are just 1 minute, that indicates [  G]1 (see
par.2.3) every 5 seconds.
If the code is right, there will be a green LED
flash and it will be possible to open the door within 5
seconds by turning the door hand clockwise.
If you enter a wrong code three times in a row,
the lock will be blocked for 5 minutes. The
blocking of the lock will be indicated periodical
red LED flashes.
3.2 Closing the Lock
Close the door and turn the door hand anti-
clockwise until it stops.
4Service Functions
It is strongly recommended to change the
settings of the lock with the door opened.
After code changing, the lock shall be tested
several times with the secure storage unit’s door
in open state.

Safe Digital Lock PS600/E36 USER MANUAL
www.promet-safe.com
Ver. 3/1 21.02.2017
The service functions will be unavailable in case
low power supply which is indicated by the
signals, please refer to par.2.3, [R]5.
4.1 Changing the Master Code [PIN1]
[ON] [Enter] [1] [Enter] [PIN1] [Enter]
[new PIN1][Enter][repeat new PIN1][Enter]
Checking the new Master code:
[ON][new PIN1][Enter]
4.2 Changing the User Code [PIN2] with the
Master Code [PIN1]
Before changing the User Code [PIN2] default
factory setting of Master code [PIN1] have to be
changed (see par.4.1).
[ON] [Enter] [2] [Enter] [PIN1] [Enter]
[new PIN2] [Enter]
[repeat new PIN2] [Enter]
Checking the new User code:
[ON][new PIN2][Enter]
4.3 Changing the User Code [PIN2] without the
Master Code
[ON] [Enter] [3] [Enter] [PIN2] [Enter]
[new PIN2] [Enter]
[repeat new PIN2] [Enter]
Checking the new User Code:
[ON][new PIN2][Enter]
4.4 Deleting the User Code
[ON] [Enter] [0] [Enter] [PIN1] [Enter]
4.5 Switching-on the Dual Code function
Before switching-on the function, make sure
you’re assigned a User Code [PIN2] see par.4.2.
[ON][Enter][7][Enter][PIN1][Enter]
4.6 Switching-off the Dual Code function
[ON][Enter][8][Enter][PIN1][Enter]
5Servicing
5.1 Changing the Battery
The pullout battery box (5) is located on the
inner side of the case (1).
Remove the screw blocking the battery box (see
Fig.5.1)
Squeeze latches and open the battery box down
(see Fig.5.1)
Fig. 5.1
Disconnect the battery from the contact pads,
placing to the right, as shown in Fig.5.2
Fig. 5.2
Remove the battery and replace it for a new one
(9V, type 6LF22).
Take the box and screw back in the reverse
order to their location.