Promet PS650/E33 User manual

Safe Digital Lock PS650/E33 USER MANUAL
www.promet-safe.com
Ver. 1/1 от 31.01.2018г.
SAFE DIGITAL LOCK PS650/E33
USER MANUAL
1Main Components
Fig. 1.1
1 –Keypad, 2 –Turning handle, 3 –Green LED [G],
4 –Red LED [R], 5 –Plastic cover for emergency power
2Definitions
2.1 Master Code [PIN1]
A set of numbers (from 6 to 8 digits) which
opens the lock and allows to operate the settings.
Before using the safe, please change the
factory Master code (see par.4.1). It is strongly
recommended to keep the master code safe
from unauthorized people.
No easily guessed numbers (birthdays, house
and phone numbers, etc.) or simple codes (1, 2,
3, 4, 5, 6) shall be chosen for the code.
Factory Master Code:
1–2–3–4–5–6
2.2 User Code [PIN2]
A set of numbers from 6 to 8 digits which opens
the lock and has limited functions to change the
settings.
The lock with the default factory settings does
not have the User code. Please see par.4.2 to
set the User code.
2.3 Signals
[G]1Short single acoustic signal with single
green LED flash (3) –confirmation of the button
pressing on the keypad.
[G]2Short double acoustic signal with double
green LED flash (3) –confirmation of successfully
finished operation.
[R]-- Long single acoustic signal with single
red LED flash (4) –error message on the user’s
actions.
[R]5Short acoustic signal sounds 5 times with
5 red LED flashes (4) –low battery message. Please
see par.7.1 how to change the battery.
3Main Functions
3.1 Opening the Lock
3.1.1 Opening with the Factory Master code
[ON][1][2][3][4][5][6][Enter]
3.1.2 Opening with the Master Code
[ON][PIN1][Enter]
3.1.3 Opening with the User Code
[ON][PIN2][Enter]
If the code is right, there will be a green LED
flash and it will be possible to open the door within 5
seconds by turning the handle (2) clockwise.
If you enter a wrong code three times in a row,
the lock will be blocked for 5 minutes. This will
be indicated via periodical red LED flashes.
3.2 Closing the Lock
Close the door and turn the handle (2) anti-
clockwise until it stops.
4Service Functions
It is strongly recommended to change the
settings of the lock with the door opened.
After code changing, the lock shall be tested
several times with the secure storage unit’s
door in open state.
The service functions will be unavailable in
case of low power supply which is indicated by
the signals, please refer to par.2.3, [R]5.
4.1 Changing the Master Code [PIN1]
[ON] [Enter] [1] [Enter] [PIN1] [Enter]
[new PIN1][Enter][repeat new PIN1][Enter]
Checking the new Master code:
[ON][new PIN1][Enter]
4.2 Changing the User Code [PIN2] with the
Master Code [PIN1]
Before changing the User Code [PIN2] default
factory setting of Master code [PIN1] has to be
changed (see par.4.1).
[ON][Enter][2][Enter]
[1-9 (user number)][Enter][PIN1][Enter]
[new PIN2][Enter]
[repeat new PIN2] [Enter]
Checking the new User Code:
[ON][new PIN2][Enter]
4.3 Changing the User Code [PIN2] without the
Master Code
[ON][Enter][3][Enter]
[1-9 (user number)][Enter][PIN2][Enter]
[new PIN2][Enter]
[repeat new PIN2] [Enter]

Safe Digital Lock PS650/E33 USER MANUAL
www.promet-safe.com
Ver. 1/1 от 31.01.2018г.
Checking the new User Code:
[ON][new PIN2][Enter]
4.4 Deleting the User Code
[ON][Enter][0][Enter][1-9 (user number)]
[Enter][PIN1][Enter]
4.5 Switching off/switching on the sound
[ON][Enter][5][Enter][PIN1][Enter]
5Time Delay Function
5.1 Switching on the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[01-99 –delay time] [1-9 –time for
opening] [Enter]
E.g.: 092 –9 minutes is the delay time, 2
minutes is the time for opening
5.2 Opening the Lock with the Time Delay
[ON] [PIN1 or PIN2] [Enter](Waiting Delay
Time. Acoustic signal will inform about
the end.)[PIN1 or PIN2] [Enter]
Pressing [Enter] during Time Delay leads to an
interruption. Operation has to be started again.
5.3 Switching off the Time Delay function
[ON] [Enter] [6] [Enter] [PIN1] [Enter]
[000] [Enter]
6Dual Code Function
6.1 Switching on the Dual Code function
Before switching on the function, make sure you
have assigned a User Code [PIN2] see par.4.2.
[ON] [Enter] [7] [Enter] [1-9 (user
number)] [Enter] [PIN1] [Enter]
6.2 Opening with the Dual Code function
[ON][PIN1][Enter]
[PIN2][Enter] –in 1 minute
If the time delay is set, you have to wait the set
delay time before entering PIN2.
You have 60 seconds to enter PIN2
independently of time of opening you have
entered before (see par.5.1)
6.3 Switching off the Dual Code function
[ON] [Enter] [8] [Enter] [PIN1] [Enter]
7Servicing
7.1 Changing the Battery
The battery is located on the inner side of the
door.
Battery box and its location depends on the safe
model
Take out the cover of the battery compartment,
change battery with a new one (9V, type 6LF22).
Take the cover or the box back to their location.
7.2 Opening the lock when the Battery is Flat
Take out the plastic cover for emergency power
(5), see Fig. 7.1.
Fig. 7.1
7.2.1 Opening the lock with a Battery
Take a new battery (9V, type 6LF22).
Press the new battery to emergency power pins
and fix it in this position (see Fig. 7.2).
Do not touch the battery’s contacts to the metal
parts of the lock in order to prevent possible
discharging of the battery.
Fig. 7.2
Enter the valid code on the keypad (1).
Disconnect the emergency battery, open the door
and change the discharged battery, see par. 7.1.
7.2.2 Opening the lock with the emergency key
Remove the screw with a screwdriver (Fig.7.3),
gently move the keypad without damaging the
cable (Fig.7.3).
Fig. 7.3
Insert a screwdriver in the groove of the drive key
and tap it until it stops (Fig.7.4), turn left (Fig.7.4)
and remove the drive key.
Insert the emergency into the keyhole, open the
lock (Fig.7.5).
Fig. 7.4 Fig. 7.5