Prorack K002 User manual

FittingKit
K002
EN
Fitting Instructions for Basic Carrier
ES
Instrucciones de montaje para el
sistema de transporte.
F
Instructions de montage pour Basic
Carrier
x 4
x 4
1
Revision No:
6C

FittingKit
K002
EN
MAX kgs (lbs)
W/P
WHD
Alfa Romeo
75 , 4dr Sedan 85- 92
EU
50 kgs (110 lbs)
50 kgs (110 lbs)
75 , 4dr Sedan Feb 85-Aug 92
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Alfa 75 , 4dr Sedan Oct 85-Jan 92
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Alfa 75 , 4dr Sedan Oct 86-Mar 92
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
Audi
80 , 4dr Sedan 87- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
80 , 4dr Sedan Apr 87-May 95
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
80 , 4dr Sedan Jan 87-Jul 92
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
80 S2, 2dr Coupe 91- 94
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
90 , 4dr Sedan 87-Jan 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
90 , 4dr Sedan Jan 87-Jul 92
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
S2 , 2dr Coupe Jul 89-Mar 95
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Daihatsu
Mira , 5dr Hatch 90- 98
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
Mira , 5dr Hatch Jul 86-Dec 95
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Mira , 5dr Hatch Nov 90-Feb 95
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Ford
Festiva , 3dr Hatch 86- 94
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Festiva WA, 5dr Hatch Oct 91-Mar 94
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
Festiva WB/WD/WF, 3dr Hatch Apr 94-Apr
01
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Laser , 5dr Hatch Feb 90-Jan 94
NZ
50 kgs (110 lbs)
50 kgs (110 lbs)
Laser KF-KH, 5dr Hatch Mar 90-Oct 94
AU
50 kgs (110 lbs)
50 kgs (110 lbs)
Telstar , 5dr Wagon Apr 88-Jul 98
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Telstar AT-AY, 5dr Hatch Nov 87-Dec 91
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Telstar Orion, 4dr Sedan Apr 88-Jul 97
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Telstar TX5, 5dr Hatch Apr 88-Jun 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Holden
Barina , 5dr Hatch Nov 85-Dec 88
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Barina MB, 5dr Hatch 85-Dec 88
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Honda
Civic , 3dr Hatch 88- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 3dr Hatch 88- 91
US
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 3dr Hatch Dec 87-Sep 91
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 3dr Hatch Nov 88-Feb 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 4dr Sedan 88- 91
US
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 4dr Sedan 88- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 4dr Sedan Dec 87-Sep 91
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Civic , 4dr Sedan Nov 88-Feb 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
2

FittingKit
K002
EN
Mazda
121 , 5dr Hatch 96- 03
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
121 Metro, 5dr Wagon Nov 96-Dec 02
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
323 , 4dr Sedan Oct 89-Mar 96
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
323 Familia, 3dr Hatch 90- 94
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
323 Familia, 4dr Sedan 90- 94
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 4dr Sedan 88- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 4dr Sedan Apr 88-Feb 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 4dr Sedan Oct 87-Nov 92
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 5dr Estate 88- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 5dr Hatch 88- 91
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 5dr Hatch Apr 88-Feb 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 5dr Wagon Jul 88-Feb 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
626 , 5dr Wagon Jun 87-Aug 92
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
626 Capella, 4dr Sedan 87- 91
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Demio , 5dr Hatch 96- 01
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
Familia Import, 3dr Hatch Feb 89-Dec 94
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
MX6 , 2dr Coupe 88-Oct 91
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
MX6 , 2dr Coupe Apr 88-Mar 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Mercedes
180E W201, 4dr Sedan Oct 82-Feb 94
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
190 W201, 4dr Sedan 82- 93
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
190 W201, 4dr Sedan Apr 82-Feb 94
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
260E , 4dr Sedan Mar 84-Mar 95
AU
60 kgs (132 lbs)
60 kgs (132 lbs)
C Class , 4dr Sedan 93- 99
ZA
60 kgs (132 lbs)
60 kgs (132 lbs)
C Class W202, 4dr Sedan 93- 01
NZ
60 kgs (132 lbs)
60 kgs (132 lbs)
C Class W202, 4dr Sedan Feb 94-Nov 01
AU
60 kgs (132 lbs)
60 kgs (132 lbs)
E Class W124, 2dr Coupe Feb 84-Dec 95
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
E Class W124, 4dr Sedan 84-Nov 95
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
E Class W124, 4dr Sedan 85- 95
EU
75 kgs (165 lbs)
75 kgs (165 lbs)
E Class W124, 4dr Sedan Aug 84-Jul 95
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Suzuki
Swift , 5dr Hatch Jan 85-Dec 88
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
Swift , 5dr Hatch Nov 86-Mar 89
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Toyota
Cressida , 4dr Sedan May 89-May 92
NZ
75 kgs (165 lbs)
75 kgs (165 lbs)
Cressida , 4dr Sedan Oct 88-Jan 93
AU
75 kgs (165 lbs)
75 kgs (165 lbs)
3

FittingKit
K002
EN
First Time Installation
Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
This kit fits type A, B, C and D.
These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

FittingKit
K002
EN
Use keys to remove covers.
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
5

FittingKit
K002
EN
Remove locking screw.
Apply protective strip as shown.
Trim if required.
Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
6

FittingKit
K002
EN
Refit locking screw so that it goes through
the hole in the clamp. Do not begin to tighten
the locking screw.
Fit rubber pad (supplied with crossbar) to foot.
Make sure the pad fits into the holes
underneath the foot.
7

FittingKit
K002
EN
Fitment
Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
Tighten adjusting screw to 5 Nm (3.7 ft lb).
8

FittingKit
K002
EN
Tighten locking screw on both legs evenly.
Check crossbar is securely attached to the
vehicle.
Use keys to fit and lock covers
9

FittingKit
K002
EN
CAUTION: Recheck all fasteners immediately
after a load is applied to the crossbars.
Regularly check screws are tight.
10

FittingKit
K002
EN
Maintenance
Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
Set crossbars a minimum distance of 700mm
(27 1/2") apart where no other distance is
specified in the fitting instructions. This is
especially important when carrying long
loads.
Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
Do not modify this product.
Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the fitting
instructions.
Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
Remove all loose or removable objects from
the load prior to loading.
Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
11

FittingKit
K002
EN
A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds, changing
of direction, and braking performance. Avoid
rapid acceleration and deceleration. Drive
carefully.
Note that the total height of the vehicle
increases when upright loads are carried.
Products should be locked during transport if
they have locks fitted.
Check and replace worn out or defective
parts.
Keep the product clean and maintained.
Never drive into a car wash with the roof rack
system fitted.
Lubricate locks and adjusting screws at
regular intervals.
Remove the products from the vehicle when
not in use. Make sure all loose parts are
stored safely.
Yakima Products, Inc.
15025 SW Koll Pkwy.
Beaverton, OR 97006-6056
USA
888-925-4621 (US)
Yakima Australia Pty Ltd
17 Hinkler Ct
Brendale QLD 4500
Brisbane
Australia
1800 143 548 (AU)
0800 4776 722 (NZ)
www.prorackgear.com
12

FittingKit
K002
ES
Primera instalación
Retire las piezas del embalaje y confirme su
contenido. Póngase en contacto con su
vendedor en el caso de que falten piezas o
éstas estén dañadas.
Este kit se adecua a los tipos A, B, C y D.
Estas instrucciones muestran la barra de
techo tipo A montada. También se aplican a
los tipos B, C y D.
NOTA: Los ganchos en este Kit de Fijación
pueden diferir de las que usted ve en la figura.
13

FittingKit
K002
ES
Utilice las llaves para retirar la tapa.
Utilice la llave Allen para desatornillar los
tornillos de ajuste en 10 vueltas.
Presione el tornillo de ajuste y tire de los pies
de la barra hacia fuera. Consulte las
instrucciones de montaje de las barras para
su ajuste.
Asegúrese de que las extremidades de la
barra estén ajustadas de forma igual.
14

FittingKit
K002
ES
Retire el tornillo de bloqueo.
Aplique la tira de protección como se
muestra.
Recorte si fuera necesario.
Ponga el gancho metálico en cada pie de
barra. NOTA: Los ganchos podrán tener
información sobre su posición de colocación
en el vehículo (Ejemplo: Delantera derecha).
15

FittingKit
K002
ES
Recoloque los tornillos de bloqueo hasta que
este se atornille al agujero en el gancho. No
apriete el tornillo de bloqueo todavía.
Ajuste la almohadilla de goma (suministrada
con las barras) a la base del pie de la barra.
Asegúrese de que la almohadilla encaja
correctamente en la base del pie de la barra.
16

FittingKit
K002
ES
Montaje
Ponga la barra en el vehículo. Las distáncia
mínima recomendada entre barras es de
700mm.
Ajuste los pies al largo de la barra para que
se encuentren a la misma distáncia de la
barra de techo y que los ganchos metálicos
se fijen firmemente en la carrocería.
Apriete el tornillo de ajuste a 5Nm (3.7 ft lb).
17

FittingKit
K002
ES
Apriete el tornillo de bloqueo en ambos pies
uniformemente.
Asegúrese de que la barra esté fijada al
vehículo de forma segura.
Utilice las llaves para instalar y cerrar las
cubiertas.
18

FittingKit
K002
ES
ATENCIÓN: Verifique regularmente si los tornillos
están apretados.
19

FittingKit
K002
ES
Mantenimiento
Limpie el techo del vehículo y las superfícies
del producto que estarán en contacto con el
techo.
Siga las instrucciones de montaje para la
instalación del producto en su vehículo.
Asegúrese de que todos los pasos se siguen
correctamente.
Ponga las barras de techo a una distáncia
mínima de 600mm (27 1/2") cuando no se
especifique otra distáncia en las
instrucciones de montaje. Esto es
especialmente importante al transportar
cargas largas.
Siempre que vuelva a montar las barras en
su vehículo, confirme que el conjunto
formado por las barras y sus pies sigue
montado de forma segura. Si parecer estar
suelto, consulte novamente las instrucciones
de montaje y reajuste.
Algunos techos solares y antenas no podrán
utilizarse cuando se instalen las barras de
techo.
No intente modificar este producto.
Considere siempre la capacidad máxima de
carga especificada en instrucciones de
montaje. No exceda la capacidad de carga
comunicada por el fabricante del vehículo
cuando esta sea inferior a la especificada en
instrucciones de montaje.
La carga no deberá repasar la extremidad
lateral de las barras. Deberá ser distribuida
uniformemente y con el menor centro de
gravedad posible.
Las cargas largas deberán estar seguradas
con cintas no elásticas en la delantera y
trasera del vehículo.
Objetos puntiagudos (ej. esquís) deberán
transportarse con la extremidad puntiaguda
direccionada hacia a la trasera del vehículo.
20