Prorack K1013 User manual

K1013
K1013
EN Fitting Instructions for Basic Carrier
x 4 x 4 x 1 x 8
x 4 x 1 x 4 x 1
x 4 x 1 x 1 x 2
Revision No: 1A 1

K1013 K1013
MAX kgs (lbs)
W/P WHD
Holden
Spark, 5dr Hatch 16-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Spark, 5dr Hatch 16-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

K1013 K1013
X
A B C 1 2 3
Spark, 5dr Hatch 16-+ (AU) -290mm 500mm - 813mm 736mm -
-11 -7/16ths" 19 11/16ths" - 32" 29" -
Spark, 5dr Hatch 16-+ (NZ) -290mm 500mm - 813mm 736mm -
-11 -7/16ths" 19 11/16ths" - 32" 29" -
3

K1013 EN
K1013
Items you will require:
●Tape measure
Pen
Cordless drill
Depth stop
Vacuum cleaner
Rust inhibitor
Small paint brush
Neutral cure silicon sealant
Rivet gun
Masking tape
Attention:
●Attaches with riveted mounts under rubber
ditch mould. Professional installation
advised.
4

K1013 EN
K1013
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●Use keys to remove covers.
5

K1013 EN
K1013
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Adjust crossbar in or out to suit vehicle.
●Please check the front of this manual for
information relating specifically to your
vehicle.
6

K1013 EN
K1013
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
●CAUTION:
●RECOMMENDED POSITION DUE TO
AIRBAGS IN ROOF:
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Apply masking tape to vehicle roof in all
four positions.
●Mark reference point on masking tape with
a pen.
7

K1013 EN
K1013
●Carefully cut tape to seperate ditch mould
from roof.
●Repeat for all four positions.
●Lift and pull ditch moulding back towards
you and remove from the vehicle.
●Position as shown.
●Line up the centre hole in the mounting
block with the marked reference points.
●Centralize PM Block.
8

K1013 EN
K1013
●Lightly mark position of outside holes of the
mounting block in the roof channel.
●Note:
●Assemble as shown.
●CAUTION:
●RECOMMENDED POSITION DUE TO
AIRBAGS IN ROOF:
●Please check the front of this manual for
information relating specifically to your
vehicle.
●CAUTION: Maximum depth 8mm.
Use 8mm drillstop over supplied 4.9mm
drill bit.
Drill two outside holes at marked positions.
9

K1013 EN
K1013
●Vacuum and clean swarf from channel.
●Treat holes to prevent corrosion.
●Apply neutral cure silicon sealant in and
around drilled holes.
10