Proteco RT37 User manual

RT37

Manual for WKPAD Wireless Keypad
WKPAD Wireless Keypad was designed for wireless entry. With the keypad, you can select up to 12 most popular rolling
code and 13 brands fixed code remote in the world. The password can keep the keypad work with security.
1 Password Input and Change
The default passwords are “8888” at factory.
Samples: Change default passwords as “1234” （four
personal identification number）
1 With the WKPAD as default setting, the passwords is
“8888”
2 Sequentially press buttons “PIN + 8888”, WKPAD read
the passwords and confirm if the passwords are correct.
The WKPAD beep 1s to indicate confirm ok. Continue
press button “PIN + 1234”, the WKPAD record the new
passwords, press button “PIN + 1234” again, WKPAD
confirm both passwords matched, WKPAD beep again
and the passwords was changed as “1234” successfully.
NOTE :Keep the new password in mind for next access.
Reset as default passwords: Remove the battery first.
Press the key “8”and holding. Reinstalled the battery into
box, the WKPAD will beep 1s. The passwords are reset as
default passwords, “8888”
2 WKPAD learn
1 The WKPAD can work as 2 channels remote with the
button “PIN” or “OK”.
2 Before the WKPAD can work with the receiver, the
remote brands must be selected by DIP switch and
the code must be learnt into the receiver first. The
brands selection shows as Table1.
3 After the brand have been selected, sequentially
press key “OK + CCCC + PIN”, (“CCCC” are current
passwords),WKPAD send necessary code into
receiver and channel 1# is learn successfully. Press
key “OK + CCCC + OK”, WKPAD send necessary code
into receiver and channel 2# is learn successfully.

Samples :Entry WKPAD into Receiver BFT
1 Open the front cover of the keypad, select the dip
position as . Now the brand is changed
as BFT rolling code. The passwords have been
changed as “1234”
2 Ready the receiver BFT, press buttons “OK + 1234 +
OK”, the backlight flash to indicate passwords input
correct. The WKPAD channel 2# should be entry into
BFT receiver successfully.
3 Press button “1234 + OK”, the BFT receiver channel
2# should works.
4 At step 2, press buttons “OK + 1234 + PIN” the
WKPAD channel 1# should be entry into BFT
receiver successfully. Press “1234 + PIN”, the BFT
receiver channel 1# should works.
3 WKPAD work
Press buttons “CCCC + PIN”, the WKPAD works as
channel 1#. Press buttons “CCCC + OK”, the WKPAD
works as channel 2#. WKPAD send corresponding
brand and button code to receiver for work.
The button codes show as Table1.
NOTE 1 All buttons must be pressed sequentially within
1s.
2 WKPAD beep once every button pressed.

Table1
Item
DIP selection for brand Brand keypad Press
Sequence
Remote
Button Work channel
1
BFT
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
2
NICE SMILO
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
3
BENICA
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
4
DEA
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#

5
ERREKA
Standard
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
6
GiBiDi
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
7
NOVOFERM
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x06 Channel 2#
9
FAAC
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
New brands will be available at next version
12
APRIMATIC
Rolling code
CCCC + PIN 0x05 Channel 1#
CCCC + OK 0x0A Channel 2#

14
CENTRION
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
15
FOX
Rolling code
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
New brands will be available at next version
item
DIP selection for brand Brand keypad press
Sequence
Remote
Button Work channel
1
PROTECO
Fixed code
CCCC + PIN 0x00 Channel 1#
CCCC + OK 0x02 Channel 2#
2
DITEC
Fixed code
CCCC + PIN 0x0E Channel 1#
CCCC + OK 0x0D Channel 2#

New brands will be available at next version
3
MOTORLINE
Fixed code
CCCC + PIN 0x04 Channel 1#
CCCC + OK 0x05 Channel 2#
4
PRASTEL
Fixed code
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
5
ROLTORE
Fixed code
CCCC + PIN 0x0E Channel 1#
CCCC + OK 0x0D Channel 2#
6
NICE FLOW
Fixed code
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
7
KINGATE
Fixed code
CCCC + PIN 0x0E Channel 1#
CCCC + OK 0x0D Channel 2#
New brands will be available at next version

8
CAME
Fixed code
CCCC + PIN 0x07 Channel 1#
CCCC + OK 0x0B Channel 2#
9
KEY
Fixed code
CCCC + PIN 0x0A Channel 1#
CCCC + OK 0x06 Channel 2#
10
ROGER
Fixed code
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
11
TANGO2
Fixed code
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
12
MARANTEC
Fixed code
433.92MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
New brands will be available at next version

13
MARANTEC
Fixed code
868MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
17
LIFT MASTER
Motor lift
433.92MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
18
LIFT MASTER
Motorlift
868MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
19
LIFTMASTER
Lobas
433.92MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK
Independent remote code
for Channel 2#
20
LIFTMASTER
Lobas
315MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#

21
LIFTMASTER
Lobas
390MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
22
LIFTMASTER
Motorlift
433.92MHz
CCCC + PIN Independent remote code
for Channel 1#
CCCC + OK Independent remote code
for Channel 2#
24
V2
433.92MHz
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
25
V2
868MHz
CCCC + PIN 0x01 Channel 1#
CCCC + OK 0x02 Channel 2#
26
SOMMER
868MHz
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
27 CARDIN CCCC + PIN 0x02 Channel 1#

433.92MHz
CCCC + OK 0x04 Channel 2#
New brands will be available at next version
28
SOMMER
433.4MHz
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
29
CARDIN
434MHz
CCCC + PIN 0x02 Channel 1#
CCCC + OK 0x04 Channel 2#
New brands will be available at next version

Clone Mode
Also, this WKPAD can work under clone mode. Set most left
2 DIP at up position, the WKPAD entry into clone mode. The
brands show in Table2.
1 Select the brand will be cloned, then press CCCC + PIN
for clone channel 1# or CCCC + OK for channel 2#.
2 Press the original remote until the WKPAD flash to
show clone successfully.
3 The WKPAD will exit learn mode after 4 seconds
without valid remote learnt.
CLONE TRANSMIT
After finish cloned, the brand can work same as original
brand.
1 Put the most left DIP down position.
2 Press CCCC + PIN for clone channel 1# or CCCC + OK for
channel 2#, the WKPAD works same as original remote.
NOTE: The clones transmit brands can NOT be selected
by the DIP switches. It’s same as the brand while
clone mode.
For example:
a. Select for clone universal rolling
code 433.92MHz.
b. Press CCCC + PIN for clone channel 1#;
c. Put most left DIP at down position, ,
now the WKPAD work as clone transmit mode. It work
perfectly same as the code just be cloned.
d. Only one brand can be cloned or works. If another
brand be cloned, the previous brand will be
overwritten.

Table2
Item
DIP selection for brand Brand keypad Press
Sequence Work channel
1
FAAC
868MHz
SLH
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
2
HORMAN
MARANTEC
FAAC
868MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
New brands will be available at next version
3
UNIVERSAL
FIXED CODE
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
4
DITEC
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#

5
FAAC
433.92MHz
SLH
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
6
CLEMSA
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
7
MARANTEC
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
New brands will be available at next version
8
UNIVERSAL
ROLLING CODE
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
9
V2
433.92MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#

10
V2
868MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
11
UNIVERSAL
FIXED CODE
306MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
12
UNIVERSAL
FIXED CODE
310MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
New brands will be available at next version
13
UNIVERSAL
FIXED CODE
315MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
14
UNIVERSAL
FIXED CODE
330MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#

15
UNIVERSAL
FIXED CODE
390MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
16
UNIVERSAL
FIXED CODE
318MHz
CCCC + PIN Channel 1#
CCCC + OK Channel 2#
Proteco S.r.l. Via Neive, 77 - 12050 CASTAGNITO (CN) ITALY
Tel. [phone] - Fax [phone] - [e-mail] - www.proteco.net