PSI PP 3034 User manual
User´s Manual
PP 3034
Page 2
PP 3034 User Manual
Acknowledgements
PCL is a Trademark of Hewle Packard Company.
A Publicaon of PSi Laser GmbH
Hommeswiese 116 a
57258 Freudenberg/Germany
hp://www.psi-laser.de
Version: 5112 991 21751 October 2021
Great care has been taken to ensure that the informaon in this handbook is accurate and
complete. However, should any errors or omissions be discovered or should any user wish to
make suggesons for improving this handbook, please feel encouraged to send us the
relevant details.
The contents of this manual are subject to change without noce.
Copyright © by PSi Laser GmbH.
All rights strictly reserved. Reproducon or issue to third pares in any form is not permied
without wrien authorizaon from the publisher.
Page 3
PP 3034 User Manual
SAFETY REGULATIONS
Safety Regulaons for the Laser Printer PP 3034 and Paper Stacker iPS 3034
The laser printer PP 3034 and the intelligent Paper Stacker iPS 3034 full the safety regulaons
according to IEC 62368-1 for informaon technology equipments.
The mains cable must be connected only to a grounded protected wall-socket. The printer´s
mains voltage must agree with the local mains voltage.
The power plug must be easily accessible at any me so that it can be disconnected immedia-
tely in case of danger or for maintenance purposes.
Before installing the printer, check the surrounding condions in which the printer is intended
to be used (see next page, Operang Environment).
During thunderstorm you should never aempt to connect or disconnect any data transfer
cable.
The power supply should only be opened and checked by authorized personnel. Maintenance
beyond the descripons of chapter 5 may only be aempted by authorized personnel. Consi-
derable dangers can arise through inappropriate repairs for the user.
This symbol is standing for a hot surface.
Note : It is to guarantee for the printer standing in a well venlated room.
Page 4
PP 3034 User Manual
We cerfy that the equipment at issue,
Type: and the correspond to the laws and
regulaons ruling electromagnec compability of appliances (2014/30/EU) and, the-
refore, full the requirements for conformity marking with the CE-sign.
To guarantee that the device stays within the limits according to the approval regulaons for
conducted and radiated emission (EN 55032, Class A) and immunity (EN 55024) in any case
shielded interface cables are to be used only.
Note: This equipment has been tested and found to comply with the limits for a di-
gital device pursuant to of the Rules. These limits are designed to provide
reasonable protecon against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio fre-
quency energy and, if not installed and used in accordance with the instrucon manual,
may cause harmful interference to radio communicaons. Operaon of this equipment
in a residenal area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Changes and modicaons not explicitly allowed by the equipment‘s manufacturer could
void the user‘s authority to operate the equipment.
This is an EN 55032 class A device. This equipment may cause interference in a
residenal installaon.
Avoid installing the printer where it is exposed to moisture or heat (e.g. direct sunlight).
The printer is designed to operate in a wide range of environmental condions.
• Temperature: + 10°C to + 35°C (+50°F to + 95°F)
• Humidity: 30% up to 85%
For best performance, store and use fanfold paper at 19° to 23° C (68° to 73°F) and a relave
humidity of 33 to 47 percent.
Note: In case of higher values for temperature and humidity the print quality will degrade!
• 100 - 110 V (-10/+6%) AC, 12 A
• 110 - 120 V (-10/+6%) AC, 11 A
• 220 - 240 V (-10/+6%) AC, 6 A
• 50 - 60 Hz
Note: To avoid an overload of the electric circuit support (parcularly for 100 to 110V or 110
to 120V) connect the power supply plug of the printer into a separate protected power
wall socket.
Page 5
PP 3034 User Manual
Operang power < 800 Wa average; (<1.300 W peak during Warming Up)
Operang current < 110 Wa
Power save ≤ 45 W
Notes: Slots and openings in the printer‘s housing are provided for venlaon. Always ensure
that these openings are not obstructed.
Also ensure that the cables of the printer do not interfere with the output paper path.
The intelligent Paper Stacker iPS 3034 can only be used in conjuncon with the printer PP 3034.
Connector not located in limited Power Source! It is only for connecng the Paper
Stacker (iPS 3034).
Use only Psi Interconnecon Cable Type 5112-293-11563 to connect the Paper Stacker with the
Printer PP3034
the chain of the motor to move the paper exit tray up and
own will start automacally or aer pushing the key at the
front side of the table.
the paper exit tray moves up and down automacally or af-
ter pushing the key at the front side of the table. Keep your
feet clear when the paper exit tray moves down. Ensure that
the cables at the rear of the printer do not interfere with the
paper path within the stacker.
The feet of the laser printer PP 3034 should be posioned into the depressions of the stacker‘s
table.
Note:
Move the Printer PP 3034 (1) unl to the edge
(3) of the iPS 3034 (2). The right and le side
(4) must be ush with the iPS.
Page 6
PP 3034 User Manual
• The unit should be kept free from moisture, dirt, dust and exposure to heat and direct sun-
light at all mes.
• Keep hands, hair and clothing away from rollers and other moving parts.
• Be sure that the proper voltage is used and that the machine is well rounded. The use of
electrical extension cords is strongly discouraged.
• For best performance, only our authorized supplies are recommended for use with this unit.
Failure to use our authorized supplies may cause damage to the unit, in which case the war-
ranty may be rendered void.
• Do not aempt to remove any Cover that is secured.
This device complies with Part 15 of the FCC Rules.
Operaon is subject to the following two condions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may
cause undesired operaon.
This equipment has been tested and found to comply with the limits for a Class A digital de-
vice, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protecon against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instrucon manual, may cause harmful
interference to radio communicaons. Operaon of this equipment in a residenal area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense. The design and producon of this unit conforms to FCC
regulaons, and any changes or modicaons must be registered with the FCC and are
subject to FCC control. Any changes made by the purchaser or user without rst contacng
the manufacturer will be subject to penalty under FCC regulaons.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Page 7
PP 3034 User Manual
This product complies with the following EU direcves:
2014/35/EU and 2014/30/EU direcves.
This declaraon is valid for the area of the European Union(EU) only.
This device must be used with shielded interface cable and shielded network cable.
The use of non-shielded cable is likely to result in interference with radio
communicaons and is prohibited under rules.
Machine Noise Regulaon: The sound pressure level at the operator posion accor-
ding to IEC 62368-1 is equal to or less than 70dB (A).
This printer is a page printer which operates by means of a laser. There is no possibility
of danger from the laser, provided the printer is operated according to the instrucons
provided in this manual.
Since radiaon emied by the laser is completely conned within protecve housing
and external covers, the laser beam cannot escape from the machine during any phase
of user operaon.
This printer is cered as a Class 1 laser product (IEC 60825-1:2014): This means that
the printer does not produce hazardous laser radiaon.
Maximum Average Radiaon Power: 37 µW at laser Aperture of mirror unit
Wave Length: 770-800 nm
This product employs a Class IIIb Laser Diode that has an invisible laser beam. The
Laser Diode and Scanning Polygon Mirror are incorporated in the print head unit. The
print head (in the interior of the printer in front of the toner cartridge) consists of the
print head unit and the mirror unit. The laser beam is emied from the print head unit,
passes through the mirror unit, and then is radiated through the laser aperture of the
mirror unit to the interior of the printer.
This printer is cered as a Class I laser product under the Regulaon Performance Stan-
dard according to the Food, Drug, and Cosmec Act of 1990. Compliance is mandatory
for laser products marketed in the United States, and is reported to the Center for De-
vices and Radiological Health (CDRH) of the U.S. Food and Drug Administraon (FDA)
of the Department of Health and Human Services (DHHS). This means that the product
does not produce hazardous laser radiaon. The label shown the indicated compliance
with the CDRH regulaons and must be aached to laser products marketed in the Uni-
ted States.
Page 8
PP 3034 User Manual
The print head unit is NOT A FIELD
SERVICE ITEM. Therefore, the print head
unit should not be opened under any
circumstances.
•
Use of controls, adjustments or performance of procedures other than those specied in
this manual may result in hazardous radiaon exposure. This is a semiconductor laser. The
maximum power of the laser diode is 15mW, and the wavelength is 770-800 nm
•
Use of controls, adjustments of performance or procedures other than those specied in
this manual may result in hazardous radiaon exposure. This is a semiconductor laser. The
maximum power of the laser diode is 15mW, and the wavelength is 770-800 nm.
Page 9
PP 3034 User Manual
•
Usynlig laserstråling ved åbning, når sikkerhedsarydere er ude af funkon. Undgå
udselse for stråling. Klasse 1 laser produkt der opfylder IEC 60825-1:2014 sikkerheds
kravene.
•
Laieen käyäminen muulla kuin tässä köyöohjeessa mainitulla tavalla saaaa alstaa
käyäjän turvallisuusluokan 1 yliävälle näkymäömälle lasersäteilylle.
Om apparaten används på annat sä än i denna bruksanvisning specicerats, kan använ-
deren utsaasr för osynling laserstrålnig, som överskrider gränsen för laserklass 1.
Avaaessa ja suojalukitus ohiteaessa olet alina nakymaomalle lasersateilylle. Aja
katso sateeseen.
Osynlig laserstråining när denna del är öppnad och spärren är urkopplad. Betrakta ej
stråien.
•
Dersum apparatet brukes på annen måte enn spesisert i denne bruksanvisning, kan bru-
keren utsees for unsynlig laserstråling som overskrider grensen for laser klasse 1.
Dee er en halvleder laser. Maksimal eeckt l laserdiode er 15mW, og bolgelengde er
770-800 nm.
SAFETY REGULATIONS
Page 12
PP 3034 User Manual
This manual covers the printer PP 3034 and the intelligent Paper Stacker iPS 3034.
The structure of this manual is such that the operator is led step-by-step through the various
procedures. Starng with unpacking and installaon of the consumables it moves on to set-
ng-up conguraon parameters and ends with the mounng of opons.
The manual is divided into the following chapters:
This chapter describes the unpacking and seng up the printer and the installaon of the
print cartridge (consumables) are explained. Aer compleng this chapter, the default prin-
ter in its fully operaonal and tested, but have not yet congured parcularly, that the con-
necon to the computer and set the various opons have not already done.
This chapter discusses in great detail the operaon of the control panel, all menu funcons,
and the general operaon of the menu. General status messages are also described.
Get the handling with the proles is explained, it is described how the printer is set, so it can
communicate with the appropriate systems environment. In this chapter you will nd the
menu tree. Then, the menu items are explained in a table.
In this chapter are the individual menu items are explained in detail.
This chapter describes the cleaning and maintenance of the printer. Also, the procedure is
described in a paper jam, and the replacement of consumables that must be done by the
user.
This chapter covers informaon on troubleshoong and repairing simple problems. All error
messages with corresponding instrucons to the user described in tabular form.
All technical details or data about the printer can be found here.
Guidelines, paper and label properes, and storage and environmental condions are de-
ned in this chapter.
Page 13
PP 3034 User Manual
This appendix describes commands extension of PCL5 and PJL in secon 1 and 2. The Bar code
programming is described in secon 5. These command structures are valid for the PP 3034
Laser Printer with PCL5 Emulaon.
All supported Symbol Sets are listed here.
Here the user can nd the order numbers of the consumables.
The following convenons are used:
Headlines and important informaon
Contains special advice to facilitate handling.
Contains important informaon to prevent damage of the equipmant.
[ONLINE] or Key funcon are always depicted in brackets or indicated by the corre-
sponding symbol.
The is the side with the paper input and the control panel. From this per-
specve, are the terms or .
Page 14
Installaon
In this chapter the precondions are described concerning the environment, the physical prere-
quisites, and the demand for space which are required for installaon of the printer.
The following table shows the values of temperature and relave humidity which are specied
for the printer and its consumables.
Temperature Relave Humidity
+10 to +23°C
+50 to +73.4°F 15 bis 45%
+10 to +35°C
+59 to +95°F 15 bis 85%
0 to +35°C
+32 to +95°F
max. 85% (at 40°C)
(104°F)
0 to +35°C
+32 to +95°F
max. 85% (at 40°C)
(104°F)
+18 to +24°C
+64.4 to +75.2°F 40 bis 60%
* The photoelectrical process in a laser printer is inuenced by the climac condions of the
environment. The herewith specied values dene a climate in which an opmal print qua-
lity is ensured. Operang the printer outside this range may lead to a reducon of the print
quality.
** It is recommended to store the consumables at a cool and dark locaon.
*** The fanfold paper should be stored in the foil packaging (see also Secon ).
The printer can be used at an altude up to 2,000 m (6,562 .).
In general there are no restricons concerning air circulaon. However, it is to be observed that
the air ow does not move the fanfold paper heavily at the paper entry and paper exit of the
printer and such may lead to paper jams.
In conjuncon with the paper stacking system care has to be taken that the air ow does not dis-
turb a proper operaon of the stacker.
Since the printer is equipped with a light-sensive photoconductor drum and opcal sensors it
shall in generally not be installed at a locaon which is exposed to sunlight. If not otherwise pos-
sible window shades have to provide for the necessary protecon.
Page 15
Installaon
Note:
If the top cover is opened to clear a paper jam or to perform maintenance acons sunbeams
would directly fall onto the photoconductor drum and would permanently destroy its surface
aer an impact period of about 1 minute.
The upper limits of the acouscal noise are shown below.
– Print operaon: < 60 dB(A)
– Stand-by: < 48 dB(A)
If an interrupon of a print operaon occurs the printer can enter the Power Save mode when for a
certain period of me whose duraon is selected at the operator panel the printer does not perform
any further operaon. In this mode most of the printer´s subsystems are disconnected from power.
The operang mode is resumed when the printer receives further data from the host system.
Mode Power consumpon
< 800 Wa average
< 1.300 Wa max.
< 110 Wa average
< 1.200 Wa max.
< 45 Wa average
The printer´s weight is 40 kg (88.18 lbs.) with all consumables included. The printer and the oponal
intelligent paper stacker both together weigh 180 lbs (82 kg).
Printer Drucker incl.
Stacker
Width 540 mm
21.26 inch
540 mm
21.26 inch
Height 498 mm
19.61 inch
1.225 mm
48.23 inch
Depth 594 mm
23.39 inch
950 mm
37.40 inch
Accessibility
To facilitate the handling of the printer (and the stacking system) by the operator the below men-
oned distances around the printer should be met minimally.
Hinweis: Das Papierablagesystem ist mit Rollen ausgestaet, so dass die gesamte Konguraon
für Wartungsarbeiten auf eine freie Fläche geschoben werden kann.
It must be ensured that the oor space where the printer is to be installed does notexceed the following
horizontal inclinaons:
• - from the front to the rear + 1°
• - from the le to the right + 2°
It must be safeguarded that an approved mains voltage wall socket is available which provides for cor-
rect and sucient current.
Page 16
Installaon
Note: The intelligent Paper Stacker (2) – also called iPS 3034 - is a special opon.
Note: Printer drivers for Windows ® are available from the PSi Laser website
Page 17
Installaon
Please check the delivery for damage. If a part is damaged,
the supplier must be contacted immediately.
• Remove top cover (1).
• Remove foam buers (6)
• Remove outer cover (2) to top.
• Remove pendulum aachment (4) later !
Li iPS 3034 (5) by two persons out of the lower
box (3).
• Remove the three security strips (5).
Note: Aer unpacking the printer, the installaon and operaon of the iPS 3034 will be described.
Page 18
Installaon
The printer PP 3034 is delivered in a package with the following label.
Note: Before unpacking the PP 3034 should be checked whether the specied mains voltage
corresponds to the local power supply. Otherwise, contact the supplier.
Please check the items from the following list to be exhausve. If parts are missing or dama-
ged, nofy your supplier
The package includes:
• PP 3034 (2)
• a power cord (3)
• a tear o bar incl. 2 screws (4)
• a short guide and a CD with documentaon and drivers (5)
• an Image Cartridge (6)
Page 19
Installaon
• Remove Styrofoam buer (1) - see previous page.
• Remove posions (3), (4) und (5) - see previous page.
• Remove IC-Cartridge (6)
• Li printer (7) with 2 persons out of the box
Aer removing the plasc foil li the printer (2) with two persons using the transport grips
(see following pictures) on the le and right side of the printer (2) and put it onto a table or
onto the iPS 3034.
Note: Do not li or hold the printer at other posions for transporng!
Page 20
Installaon
• Remove the security strips (1).
• Push the latch (2) in direcon of arrow and open the top cover (3).
• At le boom side of the printer is an addional protecve strip (4). Remove the strip
carefully.
Table of contents
Other PSI Printer manuals
