Pure Water 200 Series User manual

IMPORTANT: This manual includes important safety material; please read all
instructions before plugging power supply cord into receptacle.
Water Dispenser Owner’s
Manual – 200 Series
®

2
®
SAFETY PRECAUTIONS
Basic safety precautions should be followed when using electrical appliances, including:
• Only plug in dispenser in the sequence the manual indicates (see HOW TO INSTALL AND USE).
• In accordance with these instructions, the dispenser must be properly located and installed before use
(see HOW TO INSTALL AND USE).
• Use only bottled water in the dispenser.
• Keep all gasoline or other ammable vapors and liquids away from this and other appliances.
• Dispenser must be unplugged before cleaning, sanitizing or repairing (see CLEANING AND SANITIZING).
• Wipe up any water spills immediately after loading or unloading water bottles.
• Do not use with water that is microbiologically unsafe or of unknown quality.
• The dispenser heats water to a temperature above 190ºF (90ºC). Water temperatures above 125ºF (52ºC) can cause severe
burns or death from scalding. Most at risk of being scalded are children, the disabled and the elderly.
• Ensure the dispenser stands upright for 2 hours before loading water bottle, plugging in and turning unit on.
• Always lift dispenser by handle located on rear of unit. Lifting dispenser by faucet or faucet handles will damage the unit.
• Follow proper grounding safety precautions and instructions prior to plugging in the unit
(see GROUNDING SAFETY PRECAUTIONS AND INSTRUCTIONS).
• Supervise children when using the dispenser (see CHILD SAFETY).
GROUNDING SAFETY PRECAUTIONS AND INSTRUCTIONS
WARNING: The dispenser must be grounded – if the appliance is improperly grounded, the result
could be electric shock.
Ensure that the available power supply matches the dispenser’s voltage specications indicated on the nameplate label
(located at the rear). Please ensure that dispenser is set up so access to the power outlet and plug is unobstructed.
IMPORTANT: To provide additional protection from the risk of shock, the dispenser MUST be
connected to a ground fault circuit interrupter (GFCI) outlet at all times. Use of an extension
cord will void any warranties. See warranty document for complete terms and conditions.
Load water
bottle FIRST.
1
THEN turn on the
hot tank switch.
3
Dispense water
from hot and
cold faucets.
2
Read complete HOW TO INSTALL instruction sequence
before plugging in and turning on dispenser. Failure to
follow proper installation instructions may cause damage
to water dispenser.
STOP & READ DIRECTIONS
before plugging in dispenser.
STOP

3
®
CHILD SAFETY
CAUTION: Supervise children when using the dispenser.
The hot dispenser faucet is equipped with a child
safeguard that reduces the risk of hot water being
dispensed accidentally or by small children. To
dispense hot water, simultaneously depress the
child safety lock (located above the left hot faucet
handle) and the left hot faucet handle. Do not allow
children to hang, climb or stand on the dispenser;
the dispenser could fall over and the child could be
injured.
RECEIVING
Inspect the dispenser box carefully for any evidence of shipping or handling damage before signing to receive goods. In case of
shipping damage, claims should be led immediately with the carrier.
HOW TO INSTALL AND USE
WARNING: Read through every step in HOW TO INSTALL AND USE before plugging in or turning unit on.
1. Install dispenser on a level oor strong enough to support it when fully loaded.
2. Ensure dispenser stands upright for a minimum of 2 hours before loading water bottle, plugging in and turning on dispenser.
3. Keep dispenser unplugged and in the o position until the water bottle has been loaded and water ows through the faucets.
4. Place dispenser a minimum of 2 inches away from the wall to ensure ventilation.
5. Do not install dispenser where it will be subject to direct sunlight, heat or moisture.
6. Do not install dispenser where the temperature will go below 50ºF (10ºC) or above 100ºF (38ºC).
7. Wipe down the water bottle cap and neck to ensure there is no debris.
8. Remove tamper-evident seal from plastic
bottle cap. Do NOT remove plastic cap if
using a no-spill water bottle.
NOTE: Be sure to use a no-spill water bottle.
Using bottles without the no-spill feature
can cause leaking to occur.
9. Load water bottle by lifting and inserting it
onto the probe, ensuring bottle is fully aligned
with the dispenser and centered over the probe.
Be certain ngers and other body parts are
clear of underside of bottle. Apply slight
pressure until the plug inside the cap pushes
in and the bottle is seated. Water will begin
to ow into the tank causing air bubbles
in the bottle.
CAUTION: When loading bottle, lift
with legs to prevent injury.

4
®
10. Place a cup under the dispenser faucet. To dispense hot water, depress the child safety lock (located above the left hot faucet
handle) and the left hot faucet handle simultaneously until water ows continuously. Next, depress the right cold water faucet
handle to make sure there is a continuous ow of water.
11. Now, plug dispenser into the power supply using a GFCI outlet. Turn on the hot tank heater switch located at the rear of the unit.
12. Install drip tray grill.
13. Dispense water.
NOTE: It takes approximately 1 hour for water in the dispenser to become hot and approximately
4 hours for cold water to reach optimum temperature.
CLEANING AND SANITIZING
Your water dispenser should be thoroughly cleaned at least twice a year. If your dispenser hasn’t been used in a while, we recommend
ushing the equipment prior to cleaning. Here are instructions for do-it-yourself cleaning:
Before you start cleaning, wash your hands thoroughly with soap and water for at least 20 seconds.
TIP: The best time to clean your dispenser is when the existing water bottle is empty.
WHAT YOU’LL NEED:
• 70% rubbing alcohol or disinfecting wipes
• Dishwashing soap
• Clean cloth or soft brush
• Disposable non-latex gloves
• Hot water (about a gallon)
• Heat-resistant container, like a metal pot
• Towels to absorb any water spills
WARNING: Always use caution when handling hot water.
1. Turn o the hot tank heater switch on the back of the dispenser (Fig 1). Let the
unit stand for one hour before cleaning to allow the hot tank to cool .
2. Remove the water bottle and drain the water reservoir by dispensing water
through the hot and cold spigots .
3. Clean the cabinet, bottle receptacle and spigots with 70% rubbing alcohol or
disinfecting wipes. Vacuum or wipe the grill on the back of the dispenser to
remove any dust.
Fig 1

5
®
Fig 3 Fig 4
Fig 6
Fig 5
Fig 2
TIP: The drip tray and grill should be cleaned monthly.
4. Clean the drip tray and grill by emptying the tray and cleaning the tray
and grill with dishwashing soap or by placing them on the top rack of the
dishwasher (Fig 2).
5. Press the cover lock on the top rim of the
cooler and pull up to open (Fig 3). Remove the
separator by lifting from one edge with slow,
steady pressure. Make note of the separator
positioning before removing so that it can
be re-installed correctly (Fig 4). (Note that
the separator is designed to t tightly in the
reservoir and will require force to remove.)
Clean the separator with dishwashing soap
and dry thoroughly.
6. Carefully pour hot water into the reservoir until it is ¾ full (Fig 5). Let the water
sit for 5 minutes. Always use caution when handling hot water.
7. Wearing disposable non-latex gloves, wipe the inside of the reservoir with a clean cloth
or soft brush. Use caution as the water may still be hot to the touch (Fig 6).
8. Completely drain the water from the reservoir by dispensing the water through the
hot and cold spigots into a container .
9. Repeat steps 6 and 8 to completely ush the dispenser. It is not necessary to wipe the
inside of the reservoir a second time.

6
®
Load water
bottle FIRST.
1
THEN turn on the
hot tank switch.
3
Dispense water
from hot and
cold faucets.
2
TROUBLESHOOTING
WARNING: Always turn off dispenser and unplug from power outlet before inspecting or starting
any maintenance.
WATER IS LEAKING
• Bottle may have a puncture or crack. Remove and install new bottle.
• The no-spill bottle was loaded with the cap removed.
WATER DOES NOT FLOW FROM DISPENSER
• Make sure bottle is not empty; if empty, replace bottle.
• Make sure to push down on faucet handles fully.
• Inspect to see if there is a pinhole in the bottle; if so, replace bottle.
• Remove bottle from dispenser. Dispense two cups of water. Place the bottle back on the dispenser.
WATER TASTES BAD
• Dispenser may need to be cleaned (see CLEANING AND SANITIZING).
WATER NOT HOT OR COLD ENOUGH
• Check to make sure dispenser is plugged in and the switch is turned on.
• A fuse may be blown or the circuit breaker may be tripped; if needed, replace fuse or reset breaker.
• Dispenser may be placed in direct sunlight or may be too close to a heat source; try moving dispenser into a cool shaded area.
Fig 7
WARNING: Dispense water through the hot and cold
spigots before turning on the hot tank switch. Failure
to follow proper installation instructions may cause
damage to water dispenser.
10. Replace the separator and close the cover (Fig 7). Wipe down the cooler and the
surrounding area to dry any water spills.
11. Wash your hands thoroughly with soap and water for at least 20 seconds. Install a
full water bottle on the dispenser. Dispense water through the hot and cold spigots.
Turn on the hot tank heater switch located at the rear of the dispenser.

7
®
WARNING: The Limited 1-Year Warranty and Underwriters’ Laboratory and CE listings for the dispensers are
invalidated if any alterations, modications, or use or misuse in combination with any other machines
or devices is deemed to be the source of any claim. See warranty document for complete terms and
conditions. DS Services of America, Inc. accepts no liability (including for bodily injury) resulting from any
alterations, misuse, neglect, accidents, improper installations or repairs. The appliance is not intended
for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge without supervision by a person responsible for their safety.
IMPORTANT: The customer acknowledges that water, like other liquids, can cause damage to surfaces.
The customer takes full responsibility for placing the dispenser within a residence or business
and acknowledges that failure to address drips, leaks or spillages is at the customer’s risk.
©2020 DS Services of America, Inc.
DISPENSER IS NOISY
• Make sure the dispenser is on a level oor or counter strong enough to support it when fully loaded.
• It is normal for the bottle to make a gurgling noise as water lls the tank.
• It is normal for the dispenser or water bottle to shake when the cooling system cycles o.
PARTICLES FLOATING IN WATER
• Dispenser may need to be cleaned (see CLEANING AND SANITIZING).
• Always ensure label is fully removed from bottle cap before placing on dispenser.
• Call your water service provider if problem persists.
DISPENSER NEEDS TO BE STORED
• Always drain water completely from dispenser before shipping or storing.
TO PROPERLY DISPOSE OF YOUR DISPENSER
• Your old dispenser may have used a regulated refrigerant in its cooling system. These refrigerants are believed to harm
stratospheric ozone. If you are throwing away your old dispenser, make sure the refrigerant is removed and recovered for proper
disposal by an EPA-certied technician. If you intentionally release this refrigerant, you can be subject to nes and imprisonment
under provisions of environmental legislation.