PureLink CSW300-RX User manual

CSW300 | CSW300-RX
User Manual | Benutzerhandbuch

-02-
SAFETY WARNINGS
• To prevent short circuits, this product should only be used inside and only in dry spaces. Do not
expose the components to rain or moisture. Do not use the product close to a bath, swimming pool
etc.
• Do not expose the components of your sytems to extremely high temperatures or bright light
sources.
• In case of improper usage or if you have altered and repaired the product yourself, all guarantees
expire. PureLink does not accept responsibility in the case of improper usage of the product or
              
responsibility for additional damage other than covered by the legal product responsibility.
• This product is not a toy. Keep out of reach of children.
• Do not open the product: the device may contain live parts. The product should only be repaired
 
• Only connect the adapter to the mains after checking whether the mains voltage is the same as the
     
In that case, contact your supplier.
1. INTRODUCTION
Congratulations on your purchase of the PureLink CSW300, which allows you to send a connected HD
signal wirelessly to your HDTV or HD projector.

connection is not suitable, a long HDMI cable is not available or a cabled connection is just not an
option. You can use the CSW300 for all of your HD wireless applications, such as home theatre, cross-
room HD, meeting rooms or for game room applications.
The CSW300 also includes an easy remote control extension with the IR pass-through function, allo-
wing control of the connected source, such as set-top box, Blu-ray player or other streaming player
from the HDMI extender’s receiving end.
You can also connect up to 4 wireless receiver modules (CSW300-RX) to one single transmitter and
simultaneously use the loop-through port. The overall system capacity is limited to a maximum of
4 sink devices at once.PureLink products are manufactured with the utmost precision and of top
quality. Please read this manual carefully and follow the instructions in order to get the very results
from this product.
2. PACKAGE CONTENT
CSW300 (Set)
1x PureLink CSW300 Transmitter (TX)
1x PureLink CSW300 Receiver (RX)
4x Antenna
1x IR Receiver
1x IR Emitter
2x Power adapter 5V1A (Micro USB)
1x Manual
CSW300-RX (Receiver)
1x PureLink CSW300 Receiver (RX)
2x Antenna
1x IR Receiver
1x Power adapter 5V1A (Micro USB)
1x Manual

-03- 
3. CONNECTION
Step 1:

use another HDMI cable to connect the HDMI OUT to a display (Loop-Through).
Step 2:
Use an HDMI cable to connect the HDMI OUT of CSW300 receiver to a display device.
Step 3:
(Skip this step if you don‘t need IR Extension) Connect the IR emitter to the CSW300 transmitter. Then
place the emitter in front of the source device’s IR receiver. Connect the IR receiver to the CSW300
receiver. Then place the receiver probe in place, accessible for your remote control.
Step 4:
Connect a DC 5V1A power adapter to the power jack (MicroUSB) of the CSW300 transmitter.
Step 5:
Connect the other DC 5V1A power adapter to the power jack (MicroUSB) of the CSW300 receiver.
Step 6:
Connection completed and ready to use.

-04-
4. OPERATION
A. Installation
1. 
2. Only use the power adapters provided with the CSW300. If you use your own adapter, make sure
the power output is 5V DC, 1A.
3. In a direct line-of-sight, the maximum range of A/V signal transmission can reach up to about
100 meters. This distance can be shortened by obstacles or walls placed between transmitter and
receiver. The optimum indoor range is under 100m.
4. To ensure a good infrared remote control operation, aim your remote control* at the IR receiver of

and hold each button for about a second. The working angle of the IR receiver is +/- 15°.
5. The remote controller has to be used within the distance of 0.3m - 5m at a working angle of
+/- 15°.
* The max. transmission distance (100m) is reliant on optimum conditions. Other devices in the
vicinity using the 5GHz band (WiFi networks or other wireless video transmitters) can lead to inter-

B. Transmitter & Receiver Pairing MODE
 
 
 
4. Connection will be auto-established after once successfully paired.Wait for a few seconds for auto
connection.
C. IR Extending Function
1. Make sure the IR emitter has been installed properly on the transmitter‘s box.
2. Make sure the IR receiver has been installed properly on the receiver‘s box.
3. Use the remote control of your source device to control the source form the receiver‘s box.
NOTE: Please do not cover CSW300 transmitter and receiver with any object! Those objects can
block the air circulation and cause serious defects and injuries. The warranty will also be void.

5. LED INDICATION

below:
Condition TX RX RX UI(TV Screen)
Power on Solid RED Solid RED Startup image
Mode
(Press the button)  Solid Blue Connection through pairing
  Solid Blue Scanning
Connection & Play Solid Blue Solid Blue Video
6. FREQUENTLY ASKED QUESTIONS
1. When there is no picture presented:
Make sure the direct connection from the source device to the sink device works properly. Check,
if all connectors are connected well; check if all cables can support the transmission speed. High
Speed HDMI cables from PureLink are recommended. Unplug the power cable to restart CSW300.
2. When there is no sound:

if it works properly. Check cable to see if it supports video transmission only (DVI) or not. The
 
restart CSW300.
 

 
power of the shutter glasses (if active 3D) is on. Check the power of CSW300. Make sure, you use
the right glasses for the 3D technology in use (active or passive).
4. If the image is unstable or a snowing image shows on screen:
You might get interference form other wireless devices or heavy voltage sources inside the room
 
interference. The wireless transmission distance may be too far or blocked by a wall or another
object. Please place CSW300 in another location where you can get good signal and video
quality. Please change the direction of transmitter and receiver to get a better connection.
-05- 

-06-
5. If the wireless connection fails:
    
cable to restart CSW300.
6. IF the IR extending function is not work:
Check, if the IR emitter is connected to the CSW300 transmitter and place the emitter in
front of the source device’s IR receiver. The IR extending function of CSW300 works with all
30~60kHz IR remote control systems. Some IR remote control systems use other frequencies
or the IR signal pulse is too short and will not work with the IR extending function. In case
the IR function is not working due to interference, please re-plug the power to reconnect
automatically.
7. “Loop Through” port transmits signal, but CSW300
receiver has no signal:
Ensure that the Rx connected sink device supports higher or equal resolutions as transmitted
from Tx. The Rx side will follow the Tx side‘s resolution.

-07- 
7. TECHNICAL DATA
Resolutions
Supported HDTV resolution (HDMI) 1080p, 720p, 576p, 480p
 
 
Supported audio formats (digital) Compressed formats, PCM, AC3, Dolby 5.1
Supported standards HDMI/EDID 1.3, HDCP 2.0
Wireless
 
Operating range Up to 100m LOS
Latency Max. 0.5 seconds
Transmitter
HDMI input 1x
HDMI output 1x
IR extender Yes
Dimensions 130.0 x 83.4 x 26.5mm
Receiver
HDMI output 1x
Dimensions 130.0 x 83.4 x 26.5mm
Infrared
Supported IR frequency 30kHz - 60kHz
Power supply
Switch mode power adapter 100 - 240V AC @ 50-60Hz, 5V1A DC
The manufacturer reserves the right to make changes in the hardware, packaging, manual and any
accompanying documentation without prior notice.
            
              
incorporates HDMI® technology.

-08-
8. REQUIREMENTS / CONFORMITY
This product is compliant with the following requirements:
CE-Conformity
With the CE-marking the manufacturer declares that the product complies with the
essential requirements and guidelines of the relevant European directives.
EMC-Directive (2004/108/EC)
R&TTE- Directive (1999/5/EC)
LVD- Directive (2006/95/EC)
WEEE-Conformity
WEEE- Directive (2012/19/EU)
RoHS- Directive (2011/65/EU)

equipment or your specialized dealer. The product includes hazardous material that can cause harm

Please help to protect the environment in which we all live.

regarding regulatory compliance of our products, contact your dealer or reseller. Before putting the

Enviromental Information for customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the
product and/or its packaging must not be disposed of with unsorted municipal waste.
  
household waste streams. It is your responsibility to dispose of this and other electric and
electronic equipment via designated collection facilities appointed by the government
or local authorities. Correct disposal and recycling will help prevent potential negative

the disposal of your old equipment, please contact your local authorities, waste disposal
service or the shop where you purchased the product.

-09-
SICHERHEITSHINWEISE
• Um Kurzschlüssen vorzubeugen, nutzen Sie dieses Produkt bitte ausschließlich innerhalb
 
Bades, Schwimmbades usw. verwenden.
• Setzen Sie die Komponenten Ihres Systems nicht extrem hohen Temperaturen oder starken
Lichtquellen aus.
• Bei einer zweckwidrigen Verwendung, selbst getätigten Veränderungen oder selbst ausgeführten
 
einer falschen Verwendung des Produkts oder bei einer anderen Verwendung des Produktes als
 
gesetzliche Produkthaftung.
• Dieses Produkt ist kein Spielzeug. Bitte immer außerhalb der Reichweite von Kindern halten.
            
Stromspannung versorgt werden. Überlassen Sie Reparaturen und die Wartung ausschließlich
 
 
 
             
Kontakt zu Ihrem Händler auf.
1. EINFÜHRUNG

HDTV oder HD Projektor verteilen kann.
-
verbindung einfach nicht passend, ein entsprechend langes Kabel nicht zur Hand oder eine Kabel ist
einfach keine Option. Der CSW300 kann für jegliche Wireless HD Anwendung eingesetzt werden, z.

-
gnale verlängert werden können. So können angeschlossene Quellgeräte, wie Set-Top Boxen, BluRay
-
ert werden.
Mit dem Transmitter können bis zu 4 Stück Wireless Receiver (CSW300-RX) verbunden und gleich-

4 Anzeigegeräte zur gleichen Zeit.
Alle PureLink Produkte werden mit großer Sorgfalt hergestellt und sind von herausragender Qua-
lität. Lesen Sie diese Anleitung bitte sorgfältig durch und befolgen Sie die Anweisungen, um die

2. VERPACKUNGSINHALT
DEUTSCH
CSW300 (Set)
1x PureLink CSW300 Transmitter (TX)
1x PureLink CSW300 Receiver (RX)
4x Antenne
1x IR Empfänger
1x IR Emitter
 
1x Handbuch
CSW300-RX (Receiver)
1x PureLink CSW300 Receiver (RX)
2x Antenne
 
1x IR Empfänger
1x Handbuch

-10-
3. VERBINDUNG
Schritt 1:
Verwenden Sie ein HDMI Kabel um den HDMI Eingang des CSW300 Transmitters mit einem Quellgerät

Transmitters anzuschließen (Loop Through).
Schritt 2:
Verwenden Sie ein HDMI Kabel um den HDMI Ausgang des CSW300 Empfängers mit einem Display
zu verbinden.
Schritt 3:
(Überspringen Sie diesen Schritt, sofern Sie keine IR Verlängerung benötigen)
Verbinden Sie den IR Emitter mit dem CSW300 Transmitter. Platzieren Sie dann den den Emitter
direkt vor vor dem IR Empfänger des Quellgeräts. Verbinden Sie den IR Empfänger mit dem CSW300
           
zugänglichen Stelle.
Schritt 4:
Verbinden Sie einen DC 5V1A Stromadapter mit dem Stromeingang (Micro USB) des CSW300
Transmitters.
Schritt 5:
Verbinden Sie den anderen DC 5V1A Stromadapter mit dem Stromeingang (Micro USB) des CSW300
Empfängers.
Schritt 6:
Verbindung erfolgreich; Sie können das Produkt nun verwenden.