PureLink Luxi Electronics Presenter LU-RPR-110CR User manual

© PureLink GmbH 2015
Innovation German Enterprises.Know-How. Quality. Design.
PureLink GmbH | Von-Liebig-Straße 10 | 48432 Rheine | Germany | Tel.: [phone]-0 | E-mail: [e-mail] | Internet: www.purelink.de
Transmitter - front view
Transmitter - rear view
Receiver - front view
Receiver - rear view
Thank you for purchasing the Luxi Electronics® Presenter product. Please read through this manual before using the product.
How the product functions: Think of the daisy chain as the ow of a river; each transmitter (Tx) connects to a source device and loads
the signal to the river ow; each receiver (Rx) unloads the signal from the river ow and sends it to the display it is connected to.
The front panel and the RS-232 controls determine which source signal goes to which display.
Power options:
This product can draw power from other Presenter products in
the chain or from an optional external power supply.
Important Info:
Minimum specications for Cat.X
cables: Cat.6, UTP, 550MHz, 23/24 AWG,
solid conductors, min. 2m
TX TX RX RX
Cat.6
TITEL 01
System diagram
HDMI Input
Power Power RS232 HDMI Output Daisy Chain Input Daisy Chain Input Daisy Chain Output Ethernet Daisy Chain Output Ethernet Show Me RS-232 Status LED
Status LED SHOW ME Button
Luxi Presenter™ Quick Start Guide
LU-RPR-110CR

© PureLink GmbH 2015
Innovation German Enterprises.Know-How. Quality. Design.
PureLink GmbH | Von-Liebig-Straße 10 | 48432 Rheine | Germany | Tel.: [phone]-0 | E-mail: [e-mail] | Internet: www.purelink.de
Please contact your reseller directly for local support. See PureLink
website for RS-232 commands and user manuals.
One Tx and one Rx connected with a Cat.6 cable (min at.6, UTP,
550MHz, 23/24 AWG, solid conductors, min. 2m). Use the minimum
system to test all devices and cables to be used in bigger systems
rst, in order to isolate any potential problems.
Minimum system Support
TRANSMITTER control options RECEIVER control options
Pressing the “Show Me” button on the front panel will select the
source connected to this Tx unit; all displays will show the same
content from this Tx box. An external button can be connected to the
“Show Me” port on the rear panel. An RS-232 host connected to the
rear panel can control all functions of every unit in the chain. Make
sure both DIP switches recessed on the bottom side are in the down
(o) position.
A RS-232 host connected to the rear panel can control all functions of
every unit in the chain. Make sure both DIP switches recessed on the
bottom side are in the down (o) position.
The captive screw plugs for power, RS-232 and contact controls are
supplied with the unit. Separate the wires about 2.5 cm long; strip o
the wire insulation precisely 5 mm from the end.
Captive screw plug termination
For providing a system wide internet access. Be very careful NOT to
plug the Ethernet cable into the yellow 100s connector or vice versa!
Permanent damage may occur.
This Presenter is selected.
This Presenter is not
selected.
Communication error.
Ethernet port Front panel LED
Follow the standard
EIA 568B pin out.
RJ45 plug termination
1
2
3
4
5
6
7
8
RJ45 EIA 568B
Luxi Presenter™ Quick Start Guide
LU-RPR-110CR
Identify the positive and negative leads of the power supply before
assembly. When using a 3rd party PSU this must be checked before
assembly. CAUTION - always conrm your PSU connection with
a multimeter before inserting it into the product - a miswired
connection will cause damage to the product and void the waranty!!
Captive screw plug termination