Purmo H10 User manual

Purmo Group, Gateshead, NE11 0PG; Purmo Group Newcastle West, V42 TD39
Bracket locations:
LENGTH H J K L M
500 140 220 140
600 150 300 150
700 150 400 150
800 140 520 140
900 150 600 150
1000 140 720 140
1100 150 800 150
1200 150 900 150
1300 140 1020 140
1400 150 1100 150
1500 150 1200 150
1600 140 1320 140
1700 150 700 700 150
1800 150 720 780 150
1900 150 800 800 150
2000 150 820 880 150
2100 140 900 920 140
2200 150 920 980 150
2300 150 1000 1000 150
2400 140 1060 1060 140
2500 150 1100 1100 150
2600 150 1120 1180 150
2700 140 1200 1220 140
2800 150 1220 1280 150
2900 140 1300 1320 140
3000 150 900 900 900 150
Horizontal Flat Tube Radiator
Models*: H10, H11 (FF/RF), H20, H21(FF/RF) H22 (FF/RF) (E12 & E24 LST only)
Height: 143mm
H10, H20, H11 FF, H21 FF, H22 FF
CONNECTION DETAILS
CONNECTION LADDER
A
B
C
D
E F
G H
The standard connection configuration is ABCD. Same end connections require a baffle. Any non standard configurations should be
specified at time of order
*FF = Full Fin, RF = Reduced fin
Height: 215mm
H10, H20, H11 FF, H21 FF, H22 FF
Height: 288mm
H11 RF
Height: 288mm
H10, H20, H11 FF, H21 FF, H22 FF, H21 RF, H22 RF
Height: 360 - 868mm
H10, H20, H11 FF, H11 RF, H21, H21RF, H22, H22 RF
Safety Precaution:
Radiators are hot when in use, and as such,
present a risk of burns to users on prolonged
contact.
The temperature of a radiator is dependent on
the temperature of the system water, as set by
the system installer or end user.
Installers and users should ensure that those
who come in to close proximity to hot radiators
are aware of the risks of burns.
Installers and users should take all necessary
steps to minimise the risk of burns. If the risk
is significant, consideration should be given
to installing low temperature radiators, or to
placing guards in front of radiators.
For the correct installation of radiators it is
essential that the fixing of the radiator is carried
out in such a way that it is suitable for intended
use AND predictable misuse.
A number of elements need to be taken into
consideration including fixing method used to
secure the radiator to the wall, the type and
condition of the wall itself, and any additional
potential forces or weights, prior to finalising
installation.
IN ALL CASES IT IS STRONGLY
RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR
SIMILAR TRADESPERSON CARRIES OUT THE
INSTALLATION.
PLEASE NOTE: The fixing materials provided
are only intended for installation on walls made
of solid wood, bricks, concrete or on timber
frame stud walls where the fixing is in to the
timber. All walls being considered should have
no more than a maximum of 3 mm wall finishing.
For walls made of other materials, for example
hollow bricks, please consult your installer or
specialist supplier. ONCE AGAIN, IF YOU ARE
UNSURE, IT IS STRONGLY RECOMMENDED
THAT A SUITABLY QUALIFIED PROFESSIONAL
INSTALLER OR SIMILAR TRADESPERSON
CARRIES OUT THE INSTALLATION.
HJK
47.522.5
LENGTH
500
'J/2'
100 100 K/2 L/2J/2
K/2
J/2
LENGTH 600-1600
22.5 47.5
HJK
22.5
MH JL
47.5
22.5
LENGTH 1700-2900
K H JL
47.5
LENGTH 3000
K
LENGTH
500
100 100
95 47.5 95 47.5
47.5
95
LENGTH 600-1600
47.5
95
K
J/2
HJKH JJL
LENGTH 3000
K M
J/2 L/2
K/2J/2 K/2
H
HJL
LENGTH 1700-2900
K
LENGTH 1700-2900
MK L
J
H
K L
J
H
K
J
H
LENGTH 3000
12095 12095 12095
LENGTH
500-1600
HJK
47.5
LENGTH
500-1600
95
MK L
J
H
KH JL
47.5
LENGTH 3000
95
47.5
LENGTH 1700-2900
95
120
LENGTH
500-1600
120
LENGTH 1700 - 2900
22.5 22.5
120
LENGTH 3000
22.5
HJKHJL
KHJL
K M
DSHI-001

Purmo Group, Gateshead, NE11 0PG; Purmo Group Newcastle West, V42 TD39
DSHI-001
Information for the installer:
These radiators are for use on two pipe
pumped indirect domestic and commercial
heating installations, with a maximum working
temperature of 100°C.
The system should be designed in accordance
with BS EN 12828:2012+A1:2-14 or BS EN
12831-1:2017 as appropriate, with particular
care to avoid air entry or water discharge.
The installation work must be carried out in
accordance with recognised good practice,
and precautions taken to avoid contamination
which could lead to corrosion. In accordance
with current Building Regulations a corrosion
inhibitor or other suitable water treatment must
be used. The manufacturer’s instructions must
be strictly followed.
Failure to comply with these standards might
invalidate the manufacture’s warranty.
10 Year warranty.
The recommendations of BS 7593, Code of
Practice for treatment of water in domestic
hot water central heating systems, should be
followed where appropriate.
4
46
20
52
11.5
2020
100 Min
126
E24
184
2020
100 Min
77
38
E12
2020100 Min
139
80
H22
2020100 Min
99
60
H21
2020100 Min
99
60
H20
2020100 Min
77
38
H11
2020100 Min
77
38
H10
Hanging Brackets
LN2 Bracket A2 Wall Bracket
Bottom of radiator
mounting lug
Bottom of radiator
mounting lug
Installation Procedure:
1. Decide on the position of the radiator and
mark the mounting bracket fixing holes.
Note: Wall brackets should be mounted
in the centre of the radiator backstraps to
allow for movement.
2. Drill and plug the bracket fixing holes and
fix the brackets securely to the wall.
3. Mount the radiator on the brackets and
connect the radiator to the heating system.
4. Fit the plug and vent to the radiator.
5. Fill the system and vent the radiator.
6. Balance the system to ensure correct flow
through all radiators.
Horizontal Flat Tube Radiator
Models*: H10, H11 (FF/RF), H20, H21(FF/RF) H22 (FF/RF) (E12 & E24 LST only)
*FF = Full Fin, RF = Reduced fin
2020
100 Min
126
E24
184
2020
100 Min
77
38
E12
2020100 Min
139
80
H22
2020100 Min
99
60
H21
2020100 Min
99
60
H20
2020100 Min
77
38
H11
2020100 Min
77
38
H10