Pyle View PLRTD155 User manual

《23》
15.4" FLIP-DOWN MONITOR WITH BUILT-IN
DVD,WIRELESS FM MODULATOR & TV
PLRTD155
FEATURES
MONITOR SECTION
!HI RES TFT-LCD MONITOR 15.4” WIDE SCREEN
!HIGH RESOLUTION : 1280(H) x 800 (V)
!BRIGHTNESS : 450 CD/SQ.M
!CONTRAST RATIO : 500 : 1
!VIEWING ANGLE : 140° (LEFT/RIGHT ) 120° (TOP ) 120°( DOWN )
!OVERHEAD CONSOLE WITH TWIN DOME LIGHTS WITH LED
!IR TRANSMITTER READY FOR IR WIRELESS HEADPHONE
!BUILT-IN OSD DIGITAL FM MODUALTOR
!CREDIT CARD SIZE REMOTE CONTROL
!ON SCREEN MENU SYSTEM
!FRONT PUSHBUTTONS CONTROLS
!AUDIO / VIDEO INPUT
!MULTI SYSTEM: NTSC & PAL , SECAM AUTO SWITCH ABLE
DVD SECTION
!SLOT-IN TYPE DVD PLAYER
!PLAY BACK DISC: DVD-VIDEO, VIDEO –CD, SVCD, CD-DA, CD-RW & MP3
!10 BIT DAC VIDEO ENCORDER
!500 LINES HORIZONTAL RESOLUTIONS
!PROLOGIC DECODER
!MPEG-2 TWO CHANNEL ANALOG OUT
!24-BIT 96KHZ DAC
!FREQUENCY RESPONSE: 20 Hz to 20KHz
!GENERAL SPECIFICATIONS
!POWER REQUIREMENT: 12 V DC
!BUILT-IN TV TUNER.
!SINGLE POWER CABLE WITH NOISE FILTER CIRCUIT
!DIN INTERFACE CABLE WITH RCA JACKS FOR AUDIO AND VIDEO
CONNECTIONS
ACCESSORIES
*
* Overhead Console Mounting Bracket
* Remote Control with Batteries
* Power Connection Cable
* User's Manual
Antenna

TROUBLE SHOOTING
Symptom and Solution:
When having problem with the unit, please check this list for a
possible solution before asking for service.
Symptom Reason Solution
No Power Connections are bad
Battery is bad
Ignition is OFF
Check all cables
Check the battery
Switch the ignition to ON
No picture Connections are bad
Monitor is in incorrect setting
Check all RCA connections
Setup Monitor in correct mode
No Sound Connections are bad
Audio output setting is incorrect
Mute is ON, or Volume is 0
Check all audio connections
Setup audio output correctly
Press Mute, or increase
volume
Distorted Picture Disk is dirty or damaged
You are in fast forward or fast
Reverse mode
Clean disk, or change disk
Press PLAY to resume normal
playback
Luminance Un-
steady,or Picture
with Noise
Circuitry Influence
Bad connection
Connect source directly to
monitor
Check all cables
Unable to Play No disk is loaded
Disk is bad or dirty
Disk is upside down
Parental Lock is on
Menu is active
Insert a disk
Replace the disk or clean it
Insert disc with the label side
face up
Remove or change parental
settings
Press setup to remove menu
Keys do not
function
Power wave or other normal
phenomena( such as static)
Switch the unit off and on
again
Remote control
does not work
Remote control is too far away
from the DVD, or objects are
blocking its path
Batteries are exhausted
Use the remote control within
7 meters, point to it directly
or within a 30 degree angle.
Replace batteries
DVD unable to
play When press
the power
DVD main board doesn't drive Shut down power system
and then re-start again
《22》
Table of Contents
Caution
Read this page in details in order to protect People's health or assets.
l Driver never operates while driving
Driver may cause car accident by watching monitor while driving.
l Do not disassemble or remodel the device.
l Use proper volume while driving
l When you set -Up the device, get advice with qualified engineer.
l Do not watch monitor for long time under the condition of stopping engine.
l Do not drop or give strong impact to LCD panel.
l Do not recharge, disassemble or heat the remote control battery.
l Keep remote control battery away from child.
《1》
1. Table of Contents ------------------------------------------------------1
2. Warning -----------------------------------------------------------------1
3. Usage Notice -----------------------------------------------------------2
4. Where to Install --------------------------------------------------------3
5. Operating the Monitor-------------------------------------------------4
6. Installation your Monitor --------------------------------------------- 5
7. Setting Up The Dome Lamps-----------------------------------------6
8. Monitor Selection------------------------------------------------------ 7
9. OSD Menus in A/V Source-------------------------------------------- 8
10. DVD Section------------------------------------------------------------9
11. Remote Control---------------------------------------------------10~11
12. FM Modulator Section------------------------------------------------12
13. TV TUNER SECTION
A. OPERATIONS 13~14
B. DISPLAY---------------------------------------------------------15~19
C. TV SYSTEM AND AUDIO MODE OF PRIMARY COUNTRY- 20
14. Connection Diagram------------------------------------------------- 21
15. Trouble Shooting----------------------------------------------------- 22
16. Features----------------------------------------------------------------23
17. Accessories------------------------------------------------------------23
--------------------------------------------------

《21》
Usage Notice
Follow all warnings, precautions and maintenance as
recommended in this user's manual to maximize the life of your
LCD monitor
To avoid the damage of the LCD monitor and risk of electronic
shock, do not permeate the LCD monitor with water or any
drink.
When this happens, turn off the power, unplug the power cord
and send the LCD monitor to your local dealer or our service
cen-ter as soon as possible.
Use a regular power specification of DC 12V . Do not use any
other power supply different from the regularity.
Do not place objects on or suspend them with the power cord.
This will make the power cord damaged.
Do not assemble or twist the power cord arbitrarily. And do not
put it together with heated object.
Do not try to repair the power cord when it is damaged or
broken, change a new one immediately.
Avoid any metal objects or inflammable dropping into the LCD
monitor from ventilation slots.
Do not attempt to open or disassemble the LCD monitor
yourself as this may cause electronic shock.
When there is smile or peculiar smell in use, unplug the power
cord immediately and send it to your local dealer or our service
center.
When there is damage or breach on the LCD monitor casing,
send it to your local dealer or our service center.
Do not use this LCD monitor in the areas susceptible to
excessive dust, dirt, and humid.
Do not setup the LCD monitor in direct sunlight, extremely
hot, and cold environment.
Do not expose the LCD monitor to rain or moisture.
《2》
connection Diagram
Refer to the connection diagram for the proper connections.
You can make connections shown as below. Please ask a
qualified technician for the other connections.
DVD PLAYER
“F” CONNECTOR
2
DVD PLAYER
1

TV SYSTEM AND AUDIO MODE OF PRIMARY
" /": Show this country has no sound to output the system
Other have not listed the country and above catalogs system
same also in this machine support scope.
《2 0》
Installation
Where to Install
Before installing this unit, please check your local traffic
rules and regulations. Follow the diagram below to install
this unit in a suitable position in your car.
Do not install this unit where:
▓ It will obstruct the driver's view when the monitor is in either
open or close position.
▓ It will obstruct the operation of the airbag system.
▓ It will obstruct the operation of the vehicle, especially the
steering wheel, shift lever, or brake pedal.
▓ A driver or passengers may injure themselves while getting
into or out of the car.
《3》

Installation your Monitor
Take care to select a suitable fitting location and securing method for
the monitor:
*The unit should not distract or obstruct the driver.
*The installation should not inhibit the entry to, or the exit from the
vehicle.
*The unit should not interfere with other vehicle components e,g
(sliding sunroof).
*Make sure the unit is installed to a secure, robust mounting location
and cannot become dislodged in the event of an emergency stop.
*Do not support the unit using only the vehicle interior roof lining.
*If driving is required, take care not to penetrate through the other
sheet metal of the vehicle.
*Avoid prolonged use of the monitor when the engine is not running
to prevent draining the vehicle battery.
*Place the mounting metal plate with the nuts facing upward, then,
mount the monitor by screws included
《4》
7-3 CH ERASE
CH ERASE CH1
↑↓ADJUST
EXIT:SETUP OK:ENTER
It can to use CH+/CH- key makes the choice, and press
ENTER deletes the selected one. And the next channel will fill
a vacant position. This primitive channel will not exist to this
TV BOX In memory.
If wants to restore this primitive channel, then recreates
"AUTO FULL SCAN" will restore the channel.
《1 9》

Closing Monitor
1. Return the monitor to the central viewing position.
(Refer to the following figure)
2. Push the monitor back into the monitor base unit until
the screen engages with the release button.
Operating the Monitor
Opening the Monitor
1. Press the monitor release button to lower the LCD screen.
2. Lower the monitor until is fixed 90 from the monitor base
unit for viewing (Refer to the following figure.)
《5》
7.CH EDIT
CH EDIT
CH HIDDEN
CH SWAP
CH ERASE
↑↓ADJUST
EXIT:SETUP OK:ENTER
When the indicator is on the CH EDIT, press ENTER on the
unit/remote to display and select the item you want to change
by CH+/CH-
7-1 CH HIDDEN
CH HIDDEN CH1
YES
↑↓ADJUST
EXIT:SETUP OK:ENTER
Select by CH+/CH-, "NO" means display, "YES" means hidden
7-2 CH SWAP
CH SWAP CH1
28
↑↓ADJUST
EXIT:SETUP OK:ENTER
Select by CH+/CH-, "CH1" means you watching now, "28"
means you want to watch
《1 8》

4.AUTO FULL SCAN
PRESS ENTER TO START
↑↓ADJUST
EXIT:SETUP OK:ENTER
AUTO FULL SCAN
When the indicator is on the AUTO FULL SCAN, press ENTER
on the unit/remote to display this picture and auto full scan
channels by pressing ENTER
5.MANUAL SCAN
↑↓ADJUST
EXIT:SETUP OK:ENTER
MANUAL SCAN
When the indicator is on the MANUAL SCAN, press ENTER on
the unit/remote to display this picture and auto full scan
channels by pressing ENTER
6.FINE TUNE
↑↓ADJUST
EXIT:SETUP OK:ENTER
FINE TUNE
When the indicator is on the FINE TUNE, press ENTER on the
unit/remote to display this picture and fine tune by CH+/CH-
《1 7》
Setting Up The Dome Lamps
*Operating the dome Lamps
1. There are three function buttons for the Dome lamps operation: OFF,
DOOR, and ON. (Refer to the following figure)
A. OFF: To turn off the lamps.
B. DOOR: To make the lamps turned on
only when car doors are
opened.
C. ON: To turn on the lamps.
* The electric circuit figure
Point Power Cord Color Connection
R
W
B
Red
White
Black
Connecting With Power Supply
Connecting With Sensor of Car Doors
For Ground Connection
* Remarks:
1. There would be no any power cord puling out from "B" point as
"B" have been connected with a ground connection by screws.
2. Power supply should be used in 12 Voltages.
WW
BB
OFFOFF
DOORDOOR
ONON
LAMPSLAMPS RR
BATTERY +BATTERY +
《6》

COLOR SYSTEM
NTSC
↑↓ADJUST
EXIT:SETUP OK:ENTER
2-1.COLOR SYSTEM
On the picture of TV SYSTEM, when the indicator is on the
COLOR SYSTEM, press ENTER on the remote to display this
picture and change the mode of NTSC, PAL,SECAM,FM by
CH+/CH-
2-2.AUDIO SYSTEM
AUDIO SYSTEM
B/G
↑↓ADJUST
EXIT:SETUP OK:ENTER
On the picture of TV SYSTEM , when the indicator in on the
AUDIO SYSTEM, press ENTER on the unit/remote to display
this picture and change the audio system mode by CH+/CH-.
3.ANT SOURCE
AIR
↑↓ADJUST
EXIT:SETUP OK:ENTER
ANT SOURCE
When the indicator is on the ANT SOURCE, press ENTER on
the unit/remote to display this picture and select AIR or CABLE
by CH+/CH-. When ANT SOURCE is on AIR, this will affect the
frequency list in the AUTO SCAN.
《1 6》
POWER
MENU
UP
DOWN
MUTE
* Menu: By pressing "MENU" button to pop up the OSD menus.
When in sub-menu, press "MENU"
again to exit the
OSD menus
* / Keys: 1. Press the " / " key to increase or decrease volume.
2. Make item selection in OSD menus to increase or
decrease parameters as well.
* Mute: Press the "Mute" button from the remote control
to still the sound of the LCD monitor.
* Power:
You may also turn on or off the
monitor by this
"Power" button.
Monitor Selection
《7》

* OSD Menus in A/V Source
MAIN MENU
CVBS.1 = NTSC
H. SYNC = +15.7K Hz
V. SYNC = +60.0 Hz
BRIGHTNESS
CONTRAST
COLOR
HUE
SOURCE
AUDIO
RECALL
EXIT
1
2
SOURCE
AUTO DETECT
VIDEO 1
VIDEO 2
RETURN
AUDIO
MUTE
VOLUME
RECALL
RETURN
A. Source Selection Menu
B. Audio Input Selection Menu
VOLUME
* Quick Adjustment OSD Menus
1. By pressing "MENU" button, you may open the MAIN MENU, using
together to pick out OSD functions.
2. In order to select desire options, it is necessary to press "MENU" again to
enter each mode, than using " "/ " " to increase or decrease parameters as well.
" "/ " "
3. Press " " or " " button directly to adjust speaker volume.
4. Select out of " EXIT" mode to storing your selected parameter and
leaving OSD Menus.
《8》
DISPLAY
1.MAIN MENU
Use remote control “SETUP” button to enter/exit menu
and use “enter” button to confirm the selection.
MAIN MENU
TV SYSTEM
ANT SOURCE
AUTO FULL SCAN
MAUAL SCAN
FINE TUNE
CH EDIT
↑↓ADJUST
EXIT:SETUP OK:ENTER
Press MENU on the unit/remote to display this picture and
adjust the item by CH+/CH-
2.TV SYSTEM
TV SYSTEM
COLOR SYSTEM
AUDIO SYSTEM
CH AUDIO SET
↑↓ADJUST
EXIT:SETUP OK:ENTER
When the indicator is on the TV SYSTEM, press ENTER on the
unit/remote to display this picture and adjust the item by
CH+/CH-
《1 5》

DVD SECTION
To operate DVD by pressing the buttons on up panel:
1. POWER: Press "POWER" ON, insert the disc with printed side
face up into the disc slot, the player starts playback automatically.
2. EJECT: Press"EJECT" to eject the disc.
3. PLAY/PAUSE: Press "PAUSE" to stop playing temporary, press it
again to resume playback.
4. STOP: Press "STOP" to stop the unit playback.
When press "PLAY", it will resume playback to the last scene
you were watching. If you press "STOP" twice, it will stop
playback and revert to the initial Track/Chapter.
5. FORWARD: Press "FF" to next chapter
6. REVERSE: Press "REW" to previous chapter
1
652
43
《9》《14》
SETUP 3 ANTENNA SOURCE
First press SETUP to enter Main Menu. Move cursor to
ANTENNA SOURCE by the press-key / , and then press
ENTER to enter Sub-Menu.
Secondly select AUDIO SYSTEM by / . The items (AIR-
CABLE) can be changed by / . Press Menu back to Main
Menu. Press SETUP again, you can cancel Main Menu, or
Main Menu will be canceled automatically 30 seconds later or
move the cursor directly to the choice of next procedure.
SETUP 4 AUTO FULL SCAN
Press SETUP to enter the Main Menu; and move the cursor to
AUTO FULL SCAN by the key / , and press ENTER; then
you can enter Sub-Menu and press ENTER according to the
cue. During the Channel Scan, the Schedule will displayed in
the OSD. If press Enter, the Channel Scan will be stopped.
Press ENTER again, the Channel Scan will be performed from
the beginning. When the scanning channel movement
execution completes, the progress chart will be filled and
show "COMPLETE" in PAL/SECAM system. It will show
"COMPLETE" and "OK" in NTSC, NTSC JAPAN, NTSC
KOREA system. On the right angle demonstrated finally seeks
the channel,4 seconds later, it will go back to the TV mode,
and the program will stay from the first channel in the guide
program searching. Press SETUP again, you can cancel Main
Menu,or Main Menu will be canceled automatically 30 seconds
later.
SETUP 5
After returns to the television picture then depend on the
common television operating mode ,You can enjoys the
various countries brilliant television program.