Pylontech RV12100 User manual

Rechargeable Li-ion Battery
RV12100 User Manual
Information Version: 1.0
20RVSV0801

3
This manual introduces RV12100 from Pylontech. Please read this manual before you to
install the battery and follow the instruction carefully during the installation process. Any
confusion, please contact Pylontech immediately for advice and clarification.
Table of Contents
1.
Introduction
4
1.1
Product features
4
1.2
Product appearance
4
1.3
Scope & purpose of application
5
2.
Product Parameters
5
2.1
Battery module technical parameters
5
2.2
Panel definitions
6
2.3
System wiring
8
3.
Installation Environment
10
4.
Transportation & Storage
10
4.1
Transportation requirements
10
4.2
Storage requirements
10

4
1.
Introduction
1.1Product Features
The lithium iron phosphate battery adopts the modular series design, through the reliable
BMS system and high-performance equalization technology, the whole system has the
characteristics of flexible configuration and high reliability.
Voltage platform: 12V;
High C rate: the output power reaches sustained 1C;
High safety: lithium iron phosphate battery is safe and reliable
High reliability: interactive cooperative guarantee mechanism is adopted to improve
system reliability;
Minimalist design: bolt design of positive and negative terminals with strong
adaptability
Battery status information display, SOC display;
Ultra-long cycle life: 4000 cycles
1.2Product Appearance

5
1.3Scope & Purpose of Applications
This battery is mainly used for RV, Caravan and similar recreational vehicle usage.
It is designed to replace traditional lead acid battery types
12V battery applications also include Electric vehicles & marine use
2.
Product Parameters
2.1 Battery Module Technical parameters
No.
Item
Value
1
Nominal capacity
100 Ah
2
Nominal voltage
12.8Vdc
3
Voltage range
10 ~14.8 Vdc
4
Recommend charge voltage
10 ~14.4 Vdc
5
Continuous charging current
50A
6
Continuous discharging current
100A
7
Working temperature
-20℃～50℃
8
Humidity
5～95%
9
Cooling
Natural cooling
10
Dimension
300mm x 173mm x 220mm
11
Weight
≤15kg
12
IP rate
IP20
13
Communication
Optional
14
Parallel Connection
Support

6
2.2 Panel Definitions
Battery switch:
Press the Power Button for 1 second, the LEDs indicating health will light up and 1 second
later the battery output will be active.
Press the Power Button for 3 seconds to turn off the battery. Turning the battery back on is
locked out for 3 seconds.
Self-check lamp status：
When the initial self-check is completed, all lights will be turn on for a while and then return
to the normal display state.

7
Please refer to the table below for normal display state：
State
Soc
Status
SOC
Remark
●★Run
●★ALM
SOC4
SOC3
SOC2
SOC1
Turn off
All off
Idle
0% 25%
●
●
All SOC Light is
solid
26%-50%
●
●
51%-75%
●
●
●
76%-100%
●
●
●
●
Charge
0%-25%
●
★
The SOC top
one is flashing,
others are solid
26%-50%
★
●
51%-75%
★
●
●
76%-100%
★
●
●
●
discharge
100%-76%
★
●
●
●
●
The Run light is
flashing
75%-51%
●
●
●
50%-26%
●
●
25%-0%
●
Alarm
Alarm
★
According to SOC state
Automatically
eliminated when
value back to
normal level
Protect
Protect
●
Battery
shutdown until
value back to
normal level

8
Indicator light description:
●：Green light solid
★：Green light flashing (2S flashing)
●：Red light solid
★：Red light flashing (2S flashing)
2.3 System Wiring
2.3.1. Parallel Connection:
Before wiring the battery model, make sure all batteries are turned off. Follow the steps
shown below for wiring, with all positive poles together and all negative poles together.
Then press any battery’s Power button and the other batteries will turn on automatically.

9
Please Note:
1. The number of Parallel connections is limited to 8 pieces
2. Ensure that the voltage difference between the batteries should not exceed 0.2V
before connection. If batteries do exceed 0.2V difference then all batteries will
require a full charge so they are an equal voltage.
3. Each set of the battery external cables should have the same wire diameter and
length. This keeps the current flow of each battery consistent during operation.
4. When 2~8 batteries are connected in parallel, the charge-discharge current shall
not exceed 0.5C of the total bank capacity.
2.3.2. Series Connection:
Before wiring the battery model, make sure all batteries are turned off. Follow the steps
shown below for wiring. Then press any battery’s Power button one by one.
Please Note:
1. The maximum number of series connections is limited to 2 pcs - 24V.
2. Each battery should have the same capacity and the same voltage. Otherwise it will
affect subsequent use
3. Ensure that the voltage difference between the batteries should not exceed 0.2V
before connection. If batteries do exceed 0.2V difference then all batteries will
require a full charge so they are an equal voltage.
4. Connect all batteries in parallel (considering point 3 above) for 12-24 hours so that
batteries are equalized before connecting in series
5. If one battery goes into protective mode, the whole system will shut down

10
3.
Installation Environment
Battery operating environment requirements are as follows:
Working temperature: 0℃- 50℃
Humidity: 5% - 95%
Altitude: ＜4000m
The site environment: Away from heat, no corrosive gas, no explosive gas, no
damaging gas, no damaging insulation Conductive dust
4.
Transportation & Storage
4.1 Product Transportation requirements
Prevent violent vibration, impact or extrusion,
Do not expose to sun or rain,
In the process of loading and unloading, the battery should be handled gently to prevent
throwing, rolling and weight.
4.2 Product Storage requirements
Batteries should be stored in clean, dry and ventilated rooms where the ambient
temperature is -20℃~ 60℃and the relative humidity is no more than 85%.
Battery should avoid contact with corrosive substances, should be far away from the
source of fire and heat.
Battery storage SOC: 40% ~ 50%.
Long-term storage: before storage, the SOC should be more than 80%, and the battery
should be periodically recharged every six months to the 80% SOC.

11
Pylon Technologies Co., Ltd.
No. 73, Lane 887, ZuChongzhi Road, Zhangjiang Hi-Tech Park
Pudong, Shanghai 201203, China
T+86-21-51317699 | F+86-21-51317698
E[email protected]
Wwww.pylontech.com.cn