Pyronix Kudos DT User manual

SWITCH FEATURE POSITION MEANING
A LED Enable ON LED Enable
OFF LED Disable
B 50/60 Hz ON 50Hz
OFF 60Hz
C And/Or ON And
OFF Or
D Digital signal ON SPP+
Processing
OFF SPP+1
0C03
PYRONIX LTD
INSTALLATION
1. Remove case lid by unscrewing fixings screw as illustrated in
and unclip the PCB, taking care not to touch the Pyro sensor
labeled .
2. Choose wall fixing holes, labeled and on diagram.
3. Mark wall for fixing positions (Do not route wires near mains cabling,
avoid vibrating surfaces and mount only on a solid wall).
4. Drill fixing holes.
5. Fix case to wall.
6. Replace PCB again taking care not to touch the pyro sensor (labeled
on diagram).
7. Select and fit the appropriate lens for your application (See diagram ).
8. Using dip switches (See diagram ) select required features and modes of
operation.
9. Carry out walk test.
10. Re fit detector front cover using fixing provided (See diagram ).
POTENTIAL FALSE ALARM HAZARDS.
1. Direct sunlight on detector may cause false alarms.
2. Pets and animals may cause false alarms.
3. Mounting detector near heaters may cause false alarms.
4. Draughts from open windows may cause false alarms.
GB
C1
G2
G1
C2
G1
C1
D2 D3
DIP switches (see diagram )
Note: As Factory Default all switches are ON
1
1
1A
1A
1B
1B
1C
1C
2
2
3
3
3A
3A
3B
3B
4
4
5
5
66
7
7
OPERATION OF FEATURES
1. LED Enable / Disable (Switch A)
ON = LED Enable
OFF = LED Disable
2. 50/60 Hz (Switch B)
Factory set
3. And /Or (Switch C)
AND = Conventional dual tech, both technologies need to be
triggered simultaneously to generate an alarm.
OR = If either single technology detects prolonged intruder activity
an alarm will be generated independently.
Immunity testing carried out in AND mode.
4. Digital signal processing settings (Switch D)
SPP+ = Two opposing detection zones must be crossed.
SPP+1 = Two opposing detection zones and any other zone must be
crossed.
OPTIONAL TAMPER UNIT
Note: The Kudos detector may be fitted with an optional back tamper, which is sold separately.
SPECIFICATIONS (QUICK REFERENCE)
Model: Kudos DT
Casing: White3mm ABS Back / Front cover
White 3mm HDPE lens cover, 0.7mm in faceted area
Lens: Volumetric: 15m, 74 zones, 7 planes, 2.4m mounting height
.
Detection method: Low noise dual element pyroelectric sensor + microwave
Digital signal processing: SPP+ , SPP+1,
Detection speed: 0.3 - 3.0 m/s
Operating Voltage: 9-16 VDC
Current consumption: 40mA Quiescent
@13.8V 35mA Alarm
Relay Output: 60Vdc, 50mA (42.4Vac peak)
Mounting Height: 1.8 - 2.4m
Tamper Switch: Normally closed voltage free contacts
(12V 50mA max rating)
00 0 0
Storage Temp: -40 C / 80 C (-40 F / 176 F )
0 0 0 0
Operating Temp: -30 C / 70 C (22 F / 158 F )
Emissions: EN55022 Class B
Immunity: To new European Standard EN50130-4
Accessories: Optional back tamper
.
C
Ial at on
nst l i
Mo i w t back amper
unt ng i h t
Fla nst a alt agai wl
C ner ount
or med
D ee on all
45 egr w
C t
th t mp t onut ou e a er posi i
equi ed, i g cal el or sharr r us n sp p
i i y kni e
ut l t f
Orie ation of tpt
nt am er uni
Lef hand det si
R ght han side
id
E e a per sw t h le e
nsur t m i c v r
i cor etly r ent ed
s rco i at
osition
swi ch
tam pl e.
P t and per at
Posi i uni wi hi detecto ,
t on t t n r
usi st
thr or ia io
ng ep ee, f or ent tn
o tfuni.
nsur cl p i ur ar
l c teE e i f xt es e oa d
in t cor ect po ii , on he
he r s t on t
out sur ace he cas ng.
er f of t i
WARRANTY
This product is sold subject to our standard warranty conditions and is warranted against
defects in workmanship for a period of two years. In the interest of continuing improvement
of quality, customer care and design, Pyronix Ltd reserve the right to amend specifications
without giving prior notice
B
A1
A
G
C
A2
C1
C2
C3
D1
D
D2
D3
E
F
F1
F2
F3
G1
G2
DIAGRAMS
Coverage patterns.
PIR coverage pattern and plan view.
Microwave coverage pattern.
Dimensions and weight.
Board layout.
Pyro sensor.
DIP Switches.
Optional rear tamper.
Mounting and cable entry knockouts.
Cable entry knockouts.
Wall fixing knockouts.
Wall fixing knockouts.
Detection methods.
Detailed connections.
Control panel connections.
Tamper operation.
Alarm relay operation (N/C)
Removal and replacement of front cover and lenses.
Front cover fixing screw.
Removing and replacing the lens.
C
H1 H2 H3 H4
Power up Normal alarm Micowave PIR
R
RINS 451-5
This product is approved for use in the
Residential, Commercial and Light Industrial Environment.
Pyronix Limited
Pyronix House
Braithwell Way
Hellaby, Rotherham
S66 8QY, ENGLAND
Customer Support:
[phone] (local rate)
or [phone]
Hours: Mon to Fri, 8:00am till 6:30pm
Email: customer[email protected]
Website: www.pyronix.com
LED INDICATIONS
Kudos DT
This product complies with TS50131-2-4. at security grade 2,
environmental class 2.
UK = Suitable for use with systems installed to PD6662:2004 (AMD)
EXPORT = Suitable for use with systems installed to EN50131-1
D
Frequencies Countries
AT, BE, CH, CY, CZ,
DK, FI, FR, GR, HU, IE,
IS, IT, LT, MT, NL, PL,
SI, TR
BE, CH, CY, DK, HU,
IE, IS, IT, MT, NL, NO,
SE, SI
GB
9.9Ghz
10.5Ghz
10.6Ghz
This product operates is a
European non-harmonised
frequency band
Hereby, Pyronix, declares that this Kudos DT
is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC.
The declaration of conformity may be consulted at
www.pyronix.com/DoC
!
2
TS50131-2-4
EN50131-1
PD6662:2004
Security Grade 2
Environmental Class 2

Note:
The microwave coverage pattern will completely fill
the area that the detector is placed in.
Any area up to 15m X 15m
A2
MICROWAVE COVERAGE PATTERN
B
D
D1
F3
EF
T T
T T
Kg
79.2 g
65mm 55mm
155mm
C1
C2
F2
C
NORMAL
NORMAL
NORMALLY CLOSED OPERATION
TAMPER ALARM
ALARM
TAMP
12V
50mA
60V
50mA
9 - 16Vdc
35mA
@12Vdc
ZONE
On Off
Dip Switches
Microwave
adjustment
Tamper Switch
A = LED Disable
C = AND / OR
D = PIR Mode
B = 50 / 60Hz
Orange LED =
microwave
Red LED = Alarm
Green LED = PIR
PIR DETECTION METHODS
SPP+ = Two opposing detection zones must be crossed.
SPP+1 = Two opposing detection zones and any
other zone must be crossed.
0.3 - 3.0 m/s
SPP+
SPP+1
WIRING TO CONTROL PANEL
REMOVING AND REPLACEMENT OF FRONT COVER AND LENSES.
G
G1
G2
REMOVING THE LENS:
With the front cover removed,
unclip the lens as shown above.
NOTE:
When removing the
front cover leave the
screw in place
REPLACING THE LENS:
Locate the lens by hooking onto the three bottom pegs
and push the lens into position, ensuring that the lens
is secure via the side and top clips.
NOTE:
D2 and D3 have
been designed to
allow the detector
to be mounted in
a corner,
45 degrees to
a wall or flat
against a wall.
BOARD LAYOUT
DIMENSIONS AND WEIGHT
MOUNTING AND
CABLE ENTRY KNOCKOUTS
PYRO
SENSOR
+-NCTTA
D
C
B
A
D
C
B
D2
D3
2m 3m 4m 5m 6m 7m 8m 9m 11m 12m 13m 14m
15m
15m
14m
13m
12m
11m
9m
8m
7m
6m
5m
4m
3m
2m
1m
1m 10m
10m
SPP+ ON
SPP+1 OFF
Switch
D
Optional
rear tamper
C3
C3
C2
ON = Normal, link fitted
OFF = Optional, rear tamper
spring fitted
A1
A
15m VOLUMETRIC LENS
A
COVERAGE PATTERN AND PLAN VIEW
A1
O
90
74 zone edges
7 planes
HORIZONTAL COVERAGE
2m 3m 4m 5m 6m 7m 8m 9m 11m
12m 13m 14m
15m
15m
14m
13m
12m
11m
9m
8m
7m
6m
5m
4m
3m
2m
1m
1m 10m
10m
2.91 m
4.68 m
8.04 m
0.70 m
1.93 m
1.26 m
2.4m
VERTICAL COVERAGE