Pyronix KX10DP-WE User manual

RINS1421-1
KX10DP-WE 10m Internal detector
WHITE
3mmABS, 0.4mm HDPE in LensArea
868MHz, FMTransceiver Narrow Band
Fully Encrypted Rolling Code
300m Free Space
Low Noise Pyroelectric Sensor
High, Low
AdvancedAutomatic
10m
74
0.3 - 3.0 m/s
85
CR123A Lithium Battery
Greater than 2 years
2m to 2.8m
Front + Optional RearTamper
-20 C to 50 C
-10 C to 50 C
Wall and ceiling mounting brackets optional
EN55022 Class B
EN50130-4
Model:
Colour:
Casing:
Transmission Frequency:
Tranmission Method:
Transmission Range:
Detection Method:
Sensitivity:
Temperature Compensation:
Detection Range:
Detection Zones:
Detection Speed:
Detection Angle:
Battery:
Battery Life:
Mounting Height:
2.4m
Nominal Mounting Height:
Tamper Switch:
Storage Temperature:
Operating Temperature:
Accessories:
Emissions:
Immunity:
Pyronix Limited, Secure House, Braithwell Way,
Hellaby, Rotherham, S66 8QY. UK
Customer Support Line : [phone]
or telephone [phone]
E-mail: customer[email protected]
website: www.pyronix.com
WARRANTY
This product is sold subject to our standard warranty
conditions and is warranted against defects in
workmanship for a period of two years
In the interest of continuing improvement of quality,
customer care and design, Pyronix Ltd reserves the
right to amend specifications, without giving prior
notice.
(batteries
excluded)
This product is approved for use in the Residential,
Commercial and Light Industrial Environment.
.
Coverage Pattern
Horizontal Coverage
Vertical Coverage
®
9m
8m
7m
6m
5m
4m
3m
2m
2m 3m 4m 5m 6m 7m 8m 9m m01m1
m01
m1
85
74 zones
7 planes
O
2m 3m 4m 5m 6m 7m 8m 9m
2.4m
1m
1m
10m
EN50131-2-2:2008
EN50131-5-3:2005
Security Grade 2
Environmental Class II
2
®
KX10DP-WE Specifications
®
KX10DP-WE
10m Wireless PIR Detector
The detector will tolerate animals
of up to 20kg when the height of
the animal is less than 1 metre.

1. The detector will tolerate animals of up to
20kg when the height of the animal is less
than 1 metre.
2. Do not install the detector looking at stairs.
3. Avoid placing the detector in direct sunlight.
4. Do not mount the detector near heaters or
radiators.
5. Do not mount the detector near open
windows or air vents.
6. Mount the detector on a stable surface.
CASE LID
SCREW FITTING
NOTE: When mounting the
Part number: FPKXBRACKET
Wall Ceiling
detector, ensure that it is
not tilting backwards.
Installation Wall Mounting
The KX12DW-WE Printed Circuit Board
Learning the KX12DW-WE onto the Enforcer Control Panel
Changing The Battery
Optional Bracket Fitting Dimensions Avoiding False Alarms
69mm
(2.72”)
3mm
(0.12")
50mm
(2.2”)
117mm
(4.61”)
Kg = 105g (3.4 oz) without bracket
RINS1421-1
Header On
= HIGH)
Header Off
= LOW
SENSITIVITY
DIGITAL SIGNAL
PROCESSING SELECT
To prevent possible damage to components,
any static charge on your body needs to be
eliminated before touching the inside of the
unit. This can be accomplished by touching
some grounded/earthed metallic conductor
such as a radiator/pipework immediately
before replacing the batteries.
The batteries supplied have been chosen to
provide long service life whilst, for safety
reasons, having limited output current.
Replace only with approved batteries.
Tamper Spring
Sensitivity Settings
Piro Sensor
DO NOT TOUCH
Learn Button
Battery
Header for Rear Tamper
+
-
When you are ready to learn the device to the
control panel receiving equipment, and when the
equipment is in the learn mode (see Enforcer
Programming Manual) follow the procedure
below.
1. Make sure the battery is installed correctly
and the plastic wrapping removed.
2. Press and Hold the Learn button until the
3 LEDs start cycling through the different
colours, then release the Learn button.
3. The device is correctly learnt when the
Green LED flashes.
The three coloured LEDs give a
visual indication of the signal
strength.
Green indicates good signal strength
and is a good location to install.
Red indicates poor signal
strength and the device should not
be installed in that position.
If no LED illuminates then the device
is completely out of range.
RED BLUE GREEN
The blue LED will illuminate
when the device is activated.
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
RED BLUE GREEN
mralA
CR123A
LITHIUM
BATTERY
+-
REAR TAMPER
NVM RESET
CR123A
LITHIUM
BATTERY
+-
Pet mirror must
not be removed