PZRacing B2-Tronic BW601 User manual

B2-Tronic BW601
User Manual - v1.0 – 18/07/23
Puoi trovare l’ulti a versione del anuale, anuali applicativi, video tutorial e anuali in altre lingue, cliccando sul
link di seguito o scannerizzando il QR code a lato
You can find the latest version of the manual, application notes, video tutorial and manuals in other languages,
clicking on the link below or scanning the QR code on the side
http s ://pzracing.it/ download /
Installation
Remove the front fairing of the motorcycle to access the rear connector of the dashboard.
Disconnect the motorcycle harness connector (12pin connector) from the dashboard and connect the male/female 2-Tronic connectors to the
dashboard and to the main harness connector.
Find the dashboard connector Disconnect the dashboard
connector
Plug in the BW601 connector
to the dash of the bike
Plug in the BW601 connector
to the harness of the bike
GPS receiver installation
N.B: do not place ca eras or other sources of electro agnetic interference near the receiver to avoid the GPS signal being
disturbed
Place the receiver module with the writing facing upwards and in a horizontal position with a clear and unobstructed view of the sky, it is
reco ended to place on the steering plate as horizontal as possible trying to avoid that is facing the pilot.
The tank and the lateral air intakes of the otorcycle are highly not reco ended as the GPS receiver would be co pletely
covered by the chest and head of the rider and also during a turn the GPS receiver would be co pletely obscured by the otorcycle
itself.
Use the junction connectors to route the wire along the main harness, fix the entire length of the sensor cable, make sure that the cable is not under
tension when using the device.
N.B: the GPS receiver ust be connected, otherwise the handlebar switch of the bike will not work
Usage
N.B: to easure lap ti es it is necessary to set the dashboard display to SPORT2 or SPORT3.
N.B: if you have activated the M package for the GPS, ake sure you have set MANUAL in the LapTi er setting.
SETTING VEHICLE SETTING LAPTIMER TRIGGER : MANUAL→ → →
Start session
The receiver works fully automatically, turns on when the vehicle is turned on, hooks up to the satellites and loads the correct track automatically, then
after the vehicle has started it will start showing the lap time on the motorcycle dashboard and memorizing the data if the function has been activated.
elow is the legend of the product status via the receiver LED:
- Solid: Wi-Fi on, GPS receiver not ready. The signal which is being received is not strong enough to locate the position. If a long period of time has
passed or if you have travelled several kilometres from the place you last switched on the device, you have to wait up to 4-5 minutes to receive a signal;
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]

otherwise one minute is necessary to locate the position. If the led does not change status, position the receiver in a less restricted area because it
couldn't receive a good signal.
- Slow blink (1S off, 1S on): Wi-Fi on, GPS receiver ready. You can start your session.
- Fast blink (400 S off, 100 S on): Wi-Fi off, motorbike moving. After the bike has started and has reached 30Km/h for 5 seconds, the Wi-Fi is
turned off and the receiver will be ready to show the lap time on the dashboard.
N.B: if your circuit is not in e ory send an e ail to [e-mail] with the na e and location of the circuit, we will send you a
fir ware update with your track
Wi-Fi
The GPS receiver is equipped with an integrated Wi-
Fi module that will be used for data download and
settings related to storage. Wi-Fi turns on when the
product is turned on and turns off when the
motorcycle exceeds 30Km/h, to reactivate the Wi-Fi
it will be necessary to turn off and on the GPS
receiver.
The default data for the Wi-Fi network are the
following:
Network name: PZRacing S600-USER 1
Password: 12345678
From the software, in the Network tab, it is possible to change the last part of the network name (USER 1) and the password. Once modified it will be
necessary to close the RacePro program, turn off and on the GPS receiver.
Setting
In the Info tab you can set the GPS receiver:
Time Fuse: time fuse setting
Memorization: data recording activation (default: yes)
Directory: selection of the destination folder. In case you have not
selected any folder the software will ask for it before downloading.
Driver Name: name of the driver
Vehicle name: name of the vehicle
Filter: filter set for GPS speed
Unit: GPS speed unit set (default Km/h)
Chart (min/max): minimum and maximum chart value for GPS speed
Auto Scale (up/down): auto scale for minimum and maximum chart
value for GPS speed
Download
In the Info tab you can also execute the commands for downloading data and deleting the memory. The download speed of the product is approximately
1 minute for each hour of recording. We remind you that the memory can hold up to 6 hours of recording, so the maximum download duration is 6
minutes.
Download Last Session: download the last session recorded
Download All Sessions: download on the entire memory
Clear Memory: delete the complete memory. This operation takes about 30 seconds, do not turn off the receiver before the end of the operation.
Satellites
In the Satellites tab it will be possible to view the status of the satellites, checking
the strength of the received signal (in Db) for each satellite acquired by the GPS
receiver.
For a good reception the signal must be higher than 40Db (red line), the linked
satellites are colored LUE while those in RED are the satellites visible by the
receiver but not currently used for the position triangulation.
Test
In the Test tab you can run a short test procedure and check the date of first start-
up of the product.
PZRacing Via de Gasperi 5 – 61032 Fano (PU) Italy - Tel: [phone] – Email: [email protected]