Qdos Zero-Screw Furniture Anti-Tip Kit User manual

Zero-Screw Furniture
Anti-Tip Kit
Easy 3-Step Installation Guide
Before removing the adhesive protective liner, do a dry run and test each step
to make sure the installation will work. The SecureHold adhesive is meant to be
used once only and cannot be repositioned if done incorrectly.
Important:
Qdos wants to keep your children safe and for that we need you to do your part by
carefully reading and following the instructions below.
For installation videos and FAQs go to: QdosSafety.com
Parts List:
2 Wall
Bracket
2 Covers
for Wall
Bracket
2 Cam
Locks 2 Covers
for Cam
Lock
Adhesive
Furniture
Plate
Strap
Hinge
Pin
4 Secure
Hooks™
4 - 1.5" (35
mm) Screws

Step 1 - Positioning and attaching the Wall Brackets
The Furniture Anti-Tip Kit should be placed within 2-15”
(5-35 cm) of each end of the furniture. There are two
options how to attach the Wall Brackets. (1A) The Ze-
ro-Screw option into a hollow drywall using the Secure-
Hooks™ or (1B) with screws into the studs behind the
drywall (For plaster walls use this option). For installation
into any other wall material, use only the appropriate
hardware for that material. Consult a handyman or hard-
ware store for advice.
Insert the point of
one of the Secure-
Hooks™ in the upper
right hole in the Wall
Bracket. While turn-
ing the Hook from
side to side simply
push it in until it pen-
etrates the drywall. Continue to feed the Hook all the way
in and then turn the handle around until it locks under the
Catch. Put a second Hook in the lower left hole in the Wall
Bracket, but this Hook will turn in the opposite direction
and then lock under the Catch.
Repeat for second Wall Bracket and then attach the Covers
over the Wall Brackets to secure the Hooks.
*IMPORTANT: The adhesive is only a help to hold the Wall
Bracket during installation. The Wall Bracket MUST be at-
tached with the SecureHooks™ or screws for safety!
2A -Insert SecureHooks™ into hollow drywall
Find the center locations in between two studs toward the
ends of the furniture. Use a stud finder to locate the studs.
Carefully mark the center locations in between the studs
at the height of the furniture.
Pull the furniture out from the wall and measure 18” (45
cm) down and mark the location for the Wall Brackets.
Next peel the protective liner from the adhesive* and posi-
tion the Wall Bracket in the desired location with the strap
pointing upwards.
SecureHook™
on catch
1A

1B - Screw into Stud Behind Drywall
Locate the studs by using a stud finder. Carefully mark the
center locations of the studs at the top of the furniture.
Pull the furniture out from the wall and measure 18”
(45 cm) down and mark the location for the Wall Brackets.
Test one more time with studfinder to secure. Next peel
the protective liner from the adhesive* and position the
Wall Bracket in the desired location with the strap
pointing upwards.
Using the included screws attach the Wall Brackets
through the two screw holes in the center. Once screwed
in attach the Covers over the Wall Bracket.
*IMPORTANT: The adhesive is only a help to hold the Wall
Bracket during installation. The Wall Bracket MUST be at-
tached with the SecureHooks™ or screws for safety!
Step 2 - Attaching to the Furniture
There are two options to attach the 2 in 1 Anti-Tip TV
Straps to the furniture. (3A) On top of the furniture with
the Zero-Screw Adhesive Furniture Plate or (3B) Screw
the Cam Lock into the back of your furniture.
2A - Adhesive Furniture Plate
Push the furniture back towards the wall.
Line up the Furniture Plate so it is directly above the Wall
Bracket. Remove protective Liner and while holding the
Cam Lock against the back of the furniture, fold the Fur-
niture Plate down until it sticks. Press on it for 30 seconds
for good adhesion. Do the same for the second strap on
the other side. Note: The adhesive needs to set for 24
hours for maximum adhesion.
2B - Screws
Push the furniture back towards the wall.
Line up the Furniture Plate so it is directly above the Wall
Bracket. When attaching with screws to the back of the
furniture, the Furniture Plate can be removed by unscrew-
ing the hinge pin and pulling it out. Mark the hole loca-
tions and drill pilot holes using a 3/32” drill bit. Be careful
not to damage the top of your furniture. Attach the Cam
Lock with included screws.
2A
2B
1B

Step 3 - Taking slack out of strap
The final step is to move the furniture back closer to the
wall and take the slack out. While pushing in the release
lever on the Cam Lock, pull upwards on the strap to
remove the slack. Once the slack is gone fold the excess
strap down and put the Cover on the Cam Lock and push
the furniture back against the wall.
Note: Only remove the slack, DO NOT TIGHTEN!
Temporary Removal
In order to move the furniture out for cleaning, remove the
Cover on the Cam Locks and push the release lever while
releasing the strap downwards.
Permanent Removal
When permanently removing the Furniture Anti-Tip Kit,
release the straps all the way in the Cam Locks. Remove
SecureHooks™ or screws from the Wall Brackets. Use a
rounded knife to carefully pry behind the front edge of the
Furniture Plate until the foam tape breaks being careful
not to damage your furniture surface. For remaining tape
residue, use a finger to simply rub it away. If any residue
still remains, use a cleaner that will not damage thesurface
you are removing the residue from.
3