Qlight S80AS User manual

S80AS
Thank you for purchasing Q.Light product. Please read this
manual carefully before installing this product for safe and long
use.
▪Suitable for a bright place and a signal transfer for a long
distance with a strong strobe signal light.
▪Easy to change its lamp by taking a connector type lamp.
▪Material : Lens-AS, Body-ABS
▪Flashes : 60-80/Min.
▪Protection Class : IP44
▪ General Specification
Model
Rated
Voltage
Current
Weight
Flashes
Color
S80AS
DC12V
0.433A
0.28Kg
60~80/min.
RED-R
AMBER-A
GREEN-G
BLUE-B
DC24V
0.216A
0.28Kg
AC110V
0.076A
0.26Kg
AC220V
0.061A
0.26Kg
▪External View Drawing
S80AS
This item can connect power lines to the plate element located
at the bottom board of this item. Please read carefully this
instruction to wire.
1).Separating the bottom board and the body
Releasing the bolts(M4-1EA)④which connected the bottom
board. and separate the bottom board①and the body②then
check inside.
2).Connecting power lines
Please connect power lines refer to the upper product structure.
Releasing the bolts(M4-2EA)⑤attached on the plate element③
and connecting O type terminal or Y type terminal linked with the
power lines outside.
▪In case of product using AC voltage, connect the line without
Polarity(wire color).
▪In case of product using DC voltage, black line is negative(-).
※After finishing the power lines connection and attached the
product well, the electric power supplies by the plate element⑦
on the body②.
Indoor Outdoor
OPERATING MANUAL
Xenon Lamp Strobe Light
Product Structure
Wiring Instruction
Mounting

▪This product was manufactured with the structure for indoor use.
Installing in any direction is okay for indoor use.
▪Outdoor use is limited at a place where no water or very little
water percolates. Mounting also should be done only on the
vertical standing direction.
▪Mount at the place where exists low vibration, low impact, low
moisture and low dust as long as possible.
▪Please make a hole by a drill where you need to attach our
product and refer to below picture for a hole size. (Make sure
PCD from external view drawing.)
▪Please connect power lines refer to the upper wiring instruction.
▪Attach the bottom board①where you need to attach.
▪Make the product body drape over the bottom board part⑥
then push the product body into the bottom board.
▪Fix the product bottom board by using bolts④.
1) Warning!
Must turn off power supply and change bulb after 1 minute at
least.
▪Xenon lamp work with a high voltage, if you touch a
assembling board or lamp without power-off, you may receive
an electric shock.
2) Lens Removal
Remove lens by turning it counterclockwise. and make sure
related parts on the assembling board.
3) Change Lamp
▪Our company’s xenon lamp (1) is made as a connector type
lamp. If you pull out with a small strength, it can be separated
easily.
▪Please fit the lamp by checking a connector pin location (2) as
below picture.
Lamp removal Lamp fitting
4) Lens Assembling
Assemble the product in reverse order of separating.
▪If using voltage is seriously higher or lower than rated voltage, it
can reduce the self-life of the product or can cause a problem
on product operating. Make sure the using voltage does not
exceed +/-5% of the rated voltage.
▪If lens or body of the product is contaminated by chemicals such
as thinner, benzene, the product can be damaged, discolored
or deformed. Please be careful.
▪Do not give strong impact to the product. It can be a reason of
wire disconnection or short circuit.
▪Do not strongly pull the wire out from the product. It can cause a
disorder.
Situation
Main reason
Solution
Lamp non-working
Damage on Lamp
Change Lamp
Lamp connector
badness
re-connecting Lamp
connector
No Power Supply
Making Sure Power
Supply
Strobe working
irregularly.
Supplying Voltage
Lower than Rated
Voltage
Making Sure Using
Voltage
Change Bulb
Caution
Trouble shooting

Q-LIGHT CO., LTD.
http://www.qlightkr.com
E-mail : qlightk[email protected]
Overseas Marketing Team /Plant
Tel) 055-328-4082Fax)055-328-4083
178-1 Woogye-Ri, Sangdong-Myun, Kimhae-Si,
KyungNam, Korea