Qlightec QTG50(M)L User manual
PB 1
Ethernet LED Tower Light
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o-• the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s speci¿cation.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, ¿re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
1. During wiring or maintenance, please completely turn o-• the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a ¿re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to ¿re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to ¿re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, ¿re, electric shock and loss of life.)
Please scan the QR code for more
detailed product information.
www.qlight.com
QTG50(M)L/ QTG60(M)L/ QTG70(M)L-ETN
QTG50L-ETN-BZ
-3-24 -RAG -LW18
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• QTG50L-ETN-BZ
• QTG50ML-ETN-BZ
• QTGA50L-ETN-BZ
• QTGA50ML-ETN-BZ
•
Layer
1-1
•
Layer
2-2
•
Layer
3-3
•
Layer
4-4
•
Layer
5-5
• 12-DC12V
• 24-DC24V
• 110/220-AC110V~220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
• QTG50(M)L-ETN
Ordering Specications
5030
54
85dB
2 3
QTG60L-ETN-BZ
-3-24 -RAG -LW18
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• QTG60L-ETN-BZ
• QTG60ML-ETN-BZ
• QTGA60L-ETN-BZ
• QTGA60ML-ETN-BZ
•
Layer
1-1
•
Layer
2-2
•
Layer
3-3
•
Layer
4-4
•
Layer
5-5
• 12-DC12V
• 24-DC24V
• 110/220-AC110V~220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB18 - LW18
- QZ18 - SZ18
- QL18 - SL18
QTG70L-ETN-BZ
-3-24 -RAG -LW24
[Model number] [Layer] [Voltage] [Color] [Mounting option]
| | | | |
• QTG70L-ETN-BZ
• QTG70ML-ETN-BZ
• QTGA70L-ETN-BZ
• QTGA70ML-ETN-BZ
•
Layer
1-1
•
Layer
2-2
•
Layer
3-3
•
Layer
4-4
•
Layer
5-5
• 12-DC12V
• 24-DC24V
• 110/220-AC110V~220V
R-Red
A-Amber
G-Green
B-Blue
W-White
• (Blank)
- Standard type
• Mounting type
- LB24 - LW24
- QZ24 - SZ24
- QL24 - SL24
• QTG60(M)L-ETN
• QTG70(M)L-ETN
• QTG50(M)L-ETN • QTG60(M)L-ETN
• QTG70(M)L-ETN
Model number
Layer
Voltage Current
Certi¿cate
Color
QTG50(M)L-ETN-BZ
QTGA50(M)L-ETN-BZ
(BZ: 5 Tone Buzzer)
1
DC12V
DC24V
AC110V~220V
0.225A
0.155A
Max.0.070A
R-Red
2
DC12V
DC24V
AC110V~220V
0.300A
0.200A
Max.0.090A
R-Red
G-Green
3
DC12V
DC24V
AC110V~220V
0.375A
0.245A
Max.0.110A
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V~220V
0.450A
0.290A
Max.0.130A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V~220V
0.525A
0.335A
Max.0.150A
R-Red
A-Amber
G-Green
B-Blue
W-White
Model number
Layer
Voltage Current
Certi¿cate
Color
QTG70(M)L-ETN-BZ
QTGA70(M)L-ETN-BZ
(BZ: 5 Tone Buzzer)
1
DC12V
DC24V
AC110V~220V
0.245A
0.155A
Max.0.070A
R-Red
2
DC12V
DC24V
AC110V~220V
0.335A
0.200A
Max.0.090A
R-Red
G-Green
3
DC12V
DC24V
AC110V~220V
0.425A
0.245A
Max.0.110A
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V~220V
0.515A
0.290A
Max.0.130A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V~220V
0.605A
0.335A
Max.0.150A
R-Red
A-Amber
G-Green
B-Blue
W-White
Model number
Layer
Voltage Current
Certi¿cate
Color
QTG60(M)L-ETN-BZ
QTGA60(M)L-ETN-BZ
(BZ: 5 Tone Buzzer)
1
DC12V
DC24V
AC110V~220V
0.245A
0.155A
Max.0.070A
R-Red
2
DC12V
DC24V
AC110V~220V
0.335A
0.200A
Max.0.090A
R-Red
G-Green
3
DC12V
DC24V
AC110V~220V
0.425A
0.245A
Max.0.110A
R-Red
A-Amber
G-Green
4
DC12V
DC24V
AC110V~220V
0.515A
0.290A
Max.0.130A
R-Red
A-Amber
G-Green
B-Blue
5
DC12V
DC24V
AC110V~220V
0.605A
0.335A
Max.0.150A
R-Red
A-Amber
G-Green
B-Blue
W-White
Product Specications
Ordering Specications
2 3
Dimensions
(Units : mm)
200 28.5 150 40 13.5
L1
12
138 13.540
L2
BUZZER VOLUME
CONTROL LEVER
12.5
RJ45 LAN CONNECTOR
POWER CABLE
M18x1.5 THREAD
LAYER
1
2
3
4
5
L1 L2
432
472
512
552
592
204
244
284
324
364
PCD Ø30
360°/3-M4 BOLT
20026.5
L1
13.550
435
485
535
585
635
135
LAYER
1
2
3
4
5
L1 L2
M18x1.5 THREAD
12
12.5 123
L2
50 13.5
360°/3-M4 BOLT
BUZZER VOLUME
CONTROL LEVER
199
249
299
349
399
LAYER
1
2
3
4
5
L1 L2
120 28.5 135 50 13.5
L1
357
407
457
507
557
M24x1.5 THREAD
12
12.5 123 13.550
L2
PCD Ø50
360°/3-M4 BOLT
BUZZER VOLUME
CONTROL LEVER
199
249
299
349
399
Ø14 CABLE ENTRY
Ø14 CABLE ENTRY
Ø14 CABLE ENTRY
RJ45 LAN CONNECTOR
POWER CABLE
RJ45 LAN CONNECTOR
POWER CABLE
RJ45 LAN CONNECTOR
POWER CABLE
Ø50
Ø18
Ø60
Ø7
0Ø
70
Ø60
Ø50
Ø18
Ø24
RJ45 LAN CONNECTOR
POWER CABLE
RJ45 LAN CONNECTOR
POWER CABLE
PCD Ø40
QTG(A)50L-ETN-BZ
QTG(A)60L-ETN-BZ
QTG(A)70L-ETN-BZ
QTG(A)50ML-ETN-BZ
QTG(A)60ML-ETN-BZ
QTG(A)70ML-ETN-BZ
4 5
PC
RJ45
HUB
EtherNet Tower
VDC 12/24
EtherNet Network
DC
Power
Fuse
White
Black
LAN CABLE
• Connect RJ45 connector that is connected to UTP cable to
Ethernet port of a PC or a router.
• External power line - UL1015 AWG18(0.75sq) x 2C 400mm
• For AC type, power cable is equipped with the product.
• UTP Cable: Category 5 cable
Wiring Instructions
5. When you unzip “ETN TEST PROGRAM.zip” ¿le, following folders are created.
4. When you unzip the ¿le, there will be a ¿le with the same name below. The instructions are listed inside the ¿le.
Program Sample needed when developing
(x32bit/x64bit compatibility)
Instructions of how to use the product and library ¿le
A program for setting IP before testing the ETN device A program for setting testing the ETN device
■ Test Ethernet LED Tower Light
1. Please connect LAN cable of the tower light to the router so that
the tower light can access Ethernet network by referring left
diagram.
2. Please be sure that the power supply shall meet the product
speci¿cation accordingly.
Product Installation
2. Because the ETN tower light is connected to a hub with the PC that is same as the picture on the front page, ETN tower
light and the PC are now connected with the same network.
3. Please download the product manual, library ¿le and test program from Qlight website(www.qlight.com) or blog.qlight.com
1. Please activate default PC network only. Please run Windows CMD(Command line) of PC over the same network in order to con¿rm
network information where the Ethernet product will be connected.
Example) Windows 7 : Start(Run)->CMD->ipcon¿g /all
Windows 10 : Start menu-> Click right mouse button->CMD->ipcon¿g /all
- Please refer to below network information when the Ethernet product’s network environment is con¿gured.
Applying the Ethernet Device
Ethernet adapter
Local Area Connection
:
Connection-specific DNS Suffix . :
IP Address. . . . . . . . . . . . : 192.168.10.101
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.10.1
VAC 110V~220V
Installation wiring instructions
4 5
①
②
④
③
• Fill TCP/IP and TCP/PORT (①Network Information Setting) with IP address and port that has been setted in ethernet tower light.
• When click LAMP ON, correspond lamp turns on.
• When click LAMP OFF, correspond lamp turns off.
• Please choose appropriate sound pattern group by referring ③ Sound Group Selection area.
• You can choose sound pattern by referring ④ Sound Selection.
• Tower lamp plays sound when SOUND button is pressed.
• Tower lamp stops sound when SOUND OFF button is pressed.
Applying the Ethernet Device
6.
①
-
②
③
④
-
-
Run the “Mac_Setting.exe” program that is inside the IP Set Program Folder .
When the program is running such as the right ¿gure, click the “Mac Find” button in the
“Find Mac Address / Select” section
MAC Address of the connected device appears when you click the Device List combo box.
(If the Mac Addr does not appear, make sure that the connection status or the power supply
is functional and then retry.)
Select the MAC Addr of the device you want to change, and then click on the “Read” button.
Check the information and settings from the “Mac con¿g status”
Set the value of users network information identi¿ed in the previous chapter (subnet mask,
gateway) in each text box, and set a di-•erent IP_Addr than your PC
Apply the settings by pressing the Write button
The port is set to “20000“by default and the port number can be changed if necessary
Reconnect After Disconnecting the power from the tower light.
7. ETN Test Program Files folder includes the followings.
Test Program Library required for the test program
② Lamp Control
① Network
Information Setting
③
Sound Group Selection
④ Sound Selection
Article Detailed speci¿cation
① Network information setting - Input port on TCP/PORT and IP address on TCP/IP that set on Ethernet tower lights
② Lamp control- ON : Click the button Lamp ON
- ON/OFF : Click the button Lamp Flash
- OFF : Click the button Lamp OFF
③ Sound group selection
- WS : 5 warning sounds(mono)
- WP : 5 special warning sounds(mono)
- WM(1) : 5 Melodies(mono)
- WA(1) : 5 alarms(mono)
- WB : Software Buzzer 5 sounds(speaker type)
- Buzzer : 5 Buzzer sounds
④ Sound selection - Select 5 sounds based on model which is ¿xed on Ordering Speci¿cations
• User can select appropriate sound pattern by referring Ordering Specifications. There’re WS, WM, and WA sound patterns
and user can choose the option when placing order.
8. Run the “QLight_Lamptest_TCP” program.
6 7
Parts Denition
Cover(ABS)
Lens(PC)
Housing(ABS)
Sound volume lever
Pole(Al)
ETN CONNECTOR
ETN POWER CONNECTOR
How to Change Lens Kit
•
Disassembling lens kits
①
Twist the upper lens kit in a
counter-wise direction so the
“I” mark from both kits align.
②
Disassemble by removing the
upper lens kit from the lower
one.
•
Assembling lens kits
①
Put the two lens kits together
by aligning the upper lens’ “I”
mark and the lower lens’ “I”
mark together.
②
Lock the two kits by twisting the
upper lens kit in a counter
-
wise
direction so the upper lens’ “
◁
”
mark aligns with the lower lens’
“I” mark.
Lens modules are connected through
cone-shaped contact point. In case
the contact point is damaged, it may
cause a contact failure.
※Cautions
Contact
Point
6 7
Ø12 CABLE ENTRY
4-Ø4.5 HOLES
360°/6-Ø5 HOLES
360°/3-Ø5 HOLES
Ø12
4-Ø4.5 HOLES
60
35
40
66
20
PCD30~40
10
36
60
35
20
04
66
36
PCD30~40
50
84
50
360°/3-Ø5 HOLES
PCD40~50
86
20
10
44
Ø12 CABLE ENTRY
84
50
25
50
86
44
PCD40~50
4-Ø4.5 HOLES
4-Ø4.5 HOLES
360°/6-Ø5 HOLES
Ø12
Ø12 CABLE ENTRY
4-Ø4.5 HOLES
360°/6-Ø5 HOLES
360°/3-Ø5 HOLES
Ø12
4-Ø4.5 HOLES
60
35
40
66
20
PCD30~40
10
36
60
35
20
04
66
36
PCD30~40
50
84
50
360°/3-Ø5 HOLES
PCD40~50
86
20
10
44
Ø12 CABLE ENTRY
84
50
25
50
86
44
PCD40~50
4-Ø4.5 HOLES
4-Ø4.5 HOLES
360°/6-Ø5 HOLES
Ø12
Mounting Hole Specications
① Machine holes on the mounting surface referring to the diagram below.
② Remove the ange nuts from bolts and place the product through the mounting surface holes.
③ Fasten the ange nuts on the opposite side of the mounting surface until the product is tightened securely.
Dimensions
QTG50ML-ETN
QTG60ML-ETN
TWS45 TWA45
QTG70ML-ETN
TWS80 TWA80
Mounting Accessories (Sold Separately)
• Please refer to the dimensions below for installati on of mounting brackets
■QTG50ML-ETN/QTG60ML-ETN/QTG70ML-ETN -Direct Mounting Type Model
PCD 40
PCD 30
3-Ø5 HOLES
3-Ø5 HOLES 3-Ø5 HOLES
PCD 50
Min.Ø5 CABLE ENTRY Min.Ø5 CABLE ENTRY
Min.Ø5 CABLE ENTRY
QTG50ML-ETN-BZ QTG60ML-ETN-BZ QTG70ML-ETN-BZ
8 9
Dimensions
QTG50L-ETN
QTG60L-ETN
18mm SCREW & NUT LB18
LW18 SZ18
QZ18 SL18
QL18
■QTG50L-ETN/ QTG60L-ETN -
Pole Mounting Type Model
Ø18
Ø18
32
34 24
Ø70
51
M18x1.5
THREAD
75
52
69
Ø18
Ø18
66
52
38
34
46
50
58
Ø28
1/2" PF
4-Ø5 HOLES
12x22
CABLE ENTRY
Ø70
50
Ø18
4-Ø5 HOLES
PCD 56
4-Ø5.5 HOLES
2-Ø8.5 HOLES
PCD 54~56
Ø18
Ø18
Ø70
51.5 67
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 54~56
Ø90
4-Ø6 HOLES
Ø11 CABLE ENTRY
66
45.5
PCD 73
8 9
Dimensions
QTG70L-ETN
24mm SCREW & NUT LB24
LW24 SZ24
QZ24 SL24
QL24
■ QTG70L
-ETN - Pole Mounting Type Model
46
70
81
32
34
46
M24x1.5
THREAD
2-Ø8.5 HOLES
69.5
52
38
34
46
50
70
1/2" PF
4-Ø5 HOLES
12x22 CABLE ENTRY
33
Ø24
Ø70
55
4-Ø5.5 HOLES
PCD 54~56
Ø24
4-Ø5 HOLES
Ø90
55.5
PCD 73
Ø24
Ø35
Ø24
Ø24
Ø90
4-Ø6 HOLES
Ø11 CABLE ENTRY
Ø24
Ø90
51.567
4-Ø5.5 HOLES
Ø18 CABLE ENTRY
PCD 71~73
Ø24
66
45.5
PCD 73
Product installation direction
■ Install the product in accordance with the manual. Otherwise rainwater or moisture may penetrate into the product.
ㆍ ELECTRONIC SOUNDER/SIGNAL HORN
Sounder part shall not be facing the sky.
Sounder part shall not be facing the sky.
ㆍBEACON/SIGNALING LIGHT
Power cord inlet part shall not be facing the sky.
Power cord inlet part shall not be facing the sky.
ㆍSIGNAL TOWER LIGHTS
ㆍHEAVY-DUTY & EXPLOSION PROOF SIGNALINGS
※ For products with a protection rating of less than IPX4, please install it vertically.
※ For products with a protection rating of less than IPX4, please install it vertically.
MEMO
Head O-ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. +82-2-2679-6152(Toll free. +82-80-328-2222) Fax. +82-2-2679-6154
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. +82-55-328-1111(Toll free. +82-80-328-1111)
Qlight Overseas Sales Dept |
704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : +82-51-620-4100
Qlight Public Relations & Marketing Team O-ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. +82-51-245-0017
China Factory/ Shanghai Sales O-ce | #Room 333 Building B, #11, Lane 450, Zhenda Road, Baoshan District, Shanghai, China
Tel. +86
-
21
-
6651
-
7100 Fax. +86
-
21
-
6315
-
3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86
-
513
-
8384
-
9999 Fax +86
-
513
-
8384
-
9910
Product Operation Inquiry / Customer Support +82-51-620-4100
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea ( Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea ( Postal Code : 50805)
For your safety
Speci¿cation and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - QTG50L-ETN - 2401A
This manual suits for next models
6
Table of contents
Other Qlightec Lighting Equipment manuals
Qlightec
Qlightec S60R User manual
Qlightec
Qlightec ST45ML-NEC User manual
Qlightec
Qlightec ST56MEL-BZ-3-24-RAG-JC User manual
Qlightec
Qlightec MTG50 Series User manual
Qlightec
Qlightec SNE User manual
Qlightec
Qlightec STG40 User manual
Qlightec
Qlightec STND Series User manual
Qlightec
Qlightec S80AR User manual
Qlightec
Qlightec SKLR User manual
Qlightec
Qlightec SEA User manual
Qlightec
Qlightec S150US User manual
Qlightec
Qlightec QCML Series User manual
Qlightec
Qlightec ST45ML-Ex User manual
Qlightec
Qlightec S80ADR User manual
Qlightec
Qlightec STND100-N User manual
Qlightec
Qlightec QTG-WIZ User manual
Qlightec
Qlightec S50L User manual
Qlightec
Qlightec QLEX-SLM-650-EMG User manual
Qlightec
Qlightec SEDL User manual
Qlightec
Qlightec STA35SL User manual
Popular Lighting Equipment manuals by other brands
Somogyi
Somogyi home SLL 500 quick start guide
Govee
Govee Glide Hexagon Pro H6066 user manual
RAB
RAB T5HE-10-24P-8-EXT Series instructions
LUCIDE
LUCIDE ISOBEL 30267/01/30 installation manual
Blizzard Lighting
Blizzard Lighting SnowBlind user guide
Doughboy
Doughboy Stair Waves 0-5700-236 Owner's guide and warranty
Chauvet
Chauvet COLORstrip Quick reference guide
Inspire
Inspire TL-CDCID01-BLUE Assembly, Use, Maintenance Manual
Rigid Industries
Rigid Industries dmx led effects owner's manual
LEGRAND
LEGRAND KENALL MILLENIUM METREX METSW Series installation instructions
hager
hager EEN003 manual
Welch Allyn
Welch Allyn LS200 Procedure Light Service manual
GENLED
GENLED acolyte RIBBONLYTE Guide
Chroma
Chroma Color One 100 quick start guide
Vision & Control
Vision & Control LDLF30x240-G525/24V/-a Instructions for use
MG
MG PATLABOR IT40SA3 instruction manual
Soundcore
Soundcore BeatLight B32 user manual
Green Creative
Green Creative 36TROFKIT24DIM/277V Series installation guide