Qlightec ST56MEL-BZ-3-24-RAG-JC User manual

PB 1
ST56MEL-BZ-3-24-RAG-JC
23
85dB
6030
LED Steady/ Flashing Tower Light
Ordering Specications
Thank you for purchasing Qlight’s products. Please read this user manual carefully
prior to installation and operation to ensure safe and correct use.
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
2. Please turn o󰀨 the power of the product immediately if it fails to operate properly.
3. Carefully wire the product according to each product’s specication.
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
6. Failure to follow any of the instructions above may cause malfunction or damage to the product, re, and electric shock.
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
1. During wiring or maintenance, please completely turn o󰀨 the power of the product. (Failure to follow this may lead to an electric shock.)
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
ratings indicated for each product. (Failure to follow these instructions may cause a re to the product, electric shock, physical injury,
malfunction or damage to the product.)
3. Do not alter or repair this product. If maintenance or repair service is required, please contact your local Qlight contact point. (Failure to
follow these instructions may lead to re, electric shock, or product damage.)
4. Please apply the correct voltage to the product. (Failure to follow these instructions may lead to re, electric shock, or product damage.)
5. When the product is applied to a condition that may impact lives or property, please make sure to have a double safety device. (Failure to
follow this may cause damage to property, re, electric shock and loss of life.)
Product Specications
ST56MEL-BZ
-3-24 -RAG -JC
[Model
number] [Color] [Voltage] [Color]
| | | |
• ST56MEL-BZ • 3-3colors • 24-DC24V R-Red
A-Amber
G-Green
Model
number Voltage Current Certicate Weight Color
ST56MEL-BZ-
3-24-RAG-JC
DC24V 0.088A -
0.17kg
R-Red
A-Amber
G-Green
• Protection rating : IP23
• Ambient operating temperature : -30°C to +60°C

2 3
77
Ø56
40
12
10
167
PCD 40
Ø16 CABLE ENTRY 360°/3-M4 BOLT
ST56MEL-BZ-3-24-RAG-JC
Wiring instructions Transistor
• External power line/ external signal line - UL1015 AWG18(0.75sq) x 4C 400mm
EXTERNAL TRANSISTOR-NPN
EXTERNAL TRANSISTOR-PNP
Flash
Fuse
Red
Amber
Green
Black
Red
Amber
Green
Black
Red
Amber
Green
Black
EXTERNAL CONTACT
Steady
Steady
Layer R
Buzzer
Layer A
Layer G
Power
1
2
Flash
Fuse
Steady
Steady
Layer R
Buzzer
Layer A
Layer G
Power
1
2
Flash
Fuse
Steady
Steady
Layer R
Buzzer
Layer A
Layer G
Power
1
2
Dimensions
(Units : mm)
Wiring Instructions
• When using a transistor, please choose between the NPN transistor or PNP transistor which best matches the voltage and
product type, then connect them correctly according to the wiring diagram below.

2 3
Lens(AS)
• Machine holes on the mounting surface referring to the
diagram below.
■
Parts Denition/ Installation ■ Mounting Hole Specications
Cover(ABS)
Housing(ABS)
• First, machine holes on the mounting surface.
• The mounting hole of this product is 4.5mm in diameter.
• When machining taps, fasten the bolt through the mounting hole of
the bracket.
• When machining holes, insert the bolt through the hole of the product,
and tighten the nut from the opposite side of the mounting surface.
Parts Denition/ Installation/ Mounting Hole Specications
Installation Environment and Protection Rating
• This product is designed for use with protection rating of IP23.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection rating
indicated, it may cause malfunction or damage to the product.
• For further information, please visit our website (www.qlight.com).
Dimensions
ST56MEL-BZ-3-24-
RAG-JC
TWS45 TWA45
Mounting Accessories (Sold Separately)
• Please refer to the dimensions below for installation of mounting brackets
Flange nut
Rubber spacer
PCD 40
3-Ø4.5 HOLES
Min.Ø5 CABLE ENTRY
13
50
84
50
20
44
86
12
35
60
40
20
4-Ø5 HOLES
Ø12
360°/3-
Ø5 HOLES
Ø12 CABLE ENTRY
36
66
25
66
PCD40
50
84
50
36
PCD40~50
35
60
40
12
36
66
10
6
PCD30~40
PCD30~40
4-Ø5 HOLES
360°/3-
Ø5 HOLES
4-Ø5 HOLES
360°/3-
Ø5 HOLES
PCD40~50
4-Ø5 HOLES
360°/3-
Ø5 HOLES
Ø12 CABLE ENTRY
Ø12
13
50
84
50
20
44
86
12
35
60
40
20
4-Ø5 HOLES
Ø12
360°/3-
Ø5 HOLES
Ø12 CABLE ENTRY
36
66
25
66
PCD40
50
84
50
36
PCD40~50
35
60
40
12
36
66
10
6
PCD30~40
PCD30~40
4-Ø5 HOLES
360°/3-
Ø5 HOLES
4-Ø5 HOLES
360°/3-
Ø5 HOLES
PCD40~50
4-Ø5 HOLES
360°/3-
Ø5 HOLES
Ø12 CABLE ENTRY
Ø12

Qlight Co., Ltd. www.qlight.com | [email protected]
Head O󰀩ce | Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea
Tel. [phone](Toll free. [phone]) Fax. [phone]
Factory | 185-25, Mukbang-ro, Sangdong-myeon, Gimhae-si, Gyeongsangnamdo, Korea Tel. [phone](Toll free. [phone])
Qlight OverSEAs Sales Dept | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel : [phone]
Qlight Public Relations & Marketing Team O󰀩ce | 704 Nakdong-daero, Sasang-gu, Busan, Korea(Eomgung-Dong) Tel. [phone]
Qlight USA, Inc. www.qlight.com www.qlightusa.com | [email protected]
3003 North First Street, Suite #341, San Jose, CA 95134 USA Tel. +1 - 408 - 519 - 5740 Fax. +1 - 408 - 519 - 5739
SHANGHAI Qlight Electronic Co., Ltd. www.qlight.com www.qlightcn.com | [email protected]
China Factory/ Shanghai Sales O󰀩ce | #19, Nanda Road, Baoshan Area, Shanghai, China Tel. +86 - 21 - 6651 - 7100 Fax. +86 - 21 - 6315 - 3929
China Factory Site 2 (Qidong) | #33, Haiyan Road, Qidong High-tech Industrial Development Zone, Qidong, Jiangsu Province, China
Tel +86 - 513 - 8384 - 9999 Fax +86 - 513 - 8384 - 9910
Product Operation Inquiry / Customer Support [phone]
You can expect prompt service if you have exact information such as model name, symptom, telephone number and address.
※ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Head office : Suite #1510, STX-V Tower, 128 Gasan digital 1-ro, Geumcheon-gu, Seoul, Korea (Postal Code : 08507)
Factory : 185-25, Mukbang-Ro, Sangdong-Myeon, Gimhae-Si, Gyeongsangnam-Do, Korea (Postal Code : 50805)
For your safety
Specication and dimensions listed in this catalogue subject to change without notice for product quality improvement.
The newest product information is available on our website.(www.qlight.com)
Please read the instruction manual attached to the product carefully before installation and use.
www.qlight.com
EN - ST56MEL-BZ-3-24-RAG - 2106A