Qlightec QWCD35T User manual
1
LED Strobe Light and Alarm Sounder Combinations
QWCD35T/ QWCD35TSD
QWCD50T/ QWCD50TSD
Precautions for Safety
Failure to follow the instructions below may cause a loss of life or serious physical injury.
1. Please remove any objects that can interrupt ventilation around the product.
3OHDVHWXUQRWKHSRZHURIWKHSURGXFWLPPHGLDWHO\LILWIDLOVWRRSHUDWHSURSHUO\
&DUHIXOO\ZLUHWKHSURGXFWDFFRUGLQJWRHDFKSURGXFW¶VVSHFL¿FDWLRQ
4. Please be careful in preventing chemicals such as thinner, benzene, etc. in contact with the surface of the product.
5. Do not apply excessive force/impact to the product.
)DLOXUHWRIROORZDQ\RIWKHLQVWUXFWLRQVDERYHPD\FDXVHPDOIXQFWLRQRUGDPDJHWRWKHSURGXFW¿UHDQGHOHFWULFVKRFN
Precautions for Correct Use
Failure to follow the proper instructions may cause damage to property, the product, or malfunction of the product
that would void the warranty.
’XULQJZLULQJRUPDLQWHQDQFHSOHDVHFRPSOHWHO\WXUQRWKHSRZHURIWKHSURGXFW)DLOXUHWRIROORZWKLVPD\OHDGWRDQHOHFWULFVKRFN
2. Do not install the product in locations that subjects it to excessive dust or water other than the conditions designated by the IP protection
UDWLQJVLQGLFDWHGIRUHDFKSURGXFW)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVPD\FDXVHD¿UHWRWKHSURGXFWHOHFWULFVKRFNSK\VLFDOLQMXU\
PDOIXQFWLRQRUGDPDJHWRWKHSURGXFW
’RQRWDOWHURUUHSDLUWKLVSURGXFW,IPDLQWHQDQFHRUUHSDLUVHUYLFHLVUHTXLUHGSOHDVHFRQWDFW\RXUORFDO4OLJKWFRQWDFWSRLQW)DLOXUHWR
IROORZWKHVHLQVWUXFWLRQVPD\OHDGWR¿UHHOHFWULFVKRFNRUSURGXFWGDPDJH
3OHDVHDSSO\WKHFRUUHFWYROWDJHWRWKHSURGXFW)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVPD\OHDGWR¿UHHOHFWULFVKRFNRUSURGXFWGDPDJH
:KHQWKHSURGXFWLVDSSOLHGWRDFRQGLWLRQWKDWPD\LPSDFWOLYHVRUSURSHUW\SOHDVHPDNHVXUHWRKDYHDGRXEOHVDIHW\GHYLFH)DLOXUHWR
IROORZWKLVPD\FDXVHGDPDJHWRSURSHUW\¿UHHOHFWULFVKRFNDQGORVVRIOLIH
7KDQN\RXIRUSXUFKDVLQJ4OLJKW¶VSURGXFWV3OHDVHUHDGWKLVXVHUPDQXDOFDUHIXOO\
prior to installation and operation to ensure safe and correct use.
QWCD35T
-
110/220
-
R
-
LC
[Model number] [Voltage] [Color] [Sound selection]
| | | |
• QWCD35T
• QWCD35TSD
• QWCD50T
• QWCD50TSD
• 12/24
-DC12V-24V
• 110/220
-AC110V-220V
R-Red
A-Amber
G-Green
B-Blue
• %ODQN
- Standard type
•LC Type
-Uses external
contact
Ordering Specications
Please scan the QR code
for more
detailed product information.
www.qlight.com
-20~+50
-50~+60
-30~+60
115123 113118
HORN
66
2
Product Specications
Model number Voltage Current Sound pattern and volume &HUWL¿FDWHVWeight Color
QWCD35T
Terminal box equipped
type Built-in sound type
DC12V-24V
Max.1.300A
• Bit Input 5Ch6’FDUG
• Binary Input 31Ch
• Warning Sounds : 115dB
• MP3 Messages : 113dB
NJ
R-Red
A-Amber
G-Green
B-Blue
AC110V-220V
Max.0.350A
QWCD35TSD
Terminal box quipped type
MP3 type
DC12V-24V
Max.1.200A
NJ
AC110V-220V
Max.0.310A
QWCD50T
Terminal box equipped
type Built-in sound type
DC12V-24V
Max.5.450A
• Bit Input 5Ch6’FDUG
• Binary Input 31Ch
• Warning Sounds : 123dB
• MP3 Messages : 118dB
NJ
AC110V-220V
Max.0.900A
QWCD50TSD
Terminal box quipped type
MP3 type
DC12V-24V
Max.3.800A
NJ
AC110V-220V
Max.0.720A
• Protection rating : IP66
• Ambient operating temperature : -30°C to +60°C (QWCD35T, QWCD50T - Standard)
-50°C to +60°C (QWCD35T, QWCD50T - Low temperature type only DC)
-20°C to +50°C (QWCD35TSD, QWCD50TSD)
Dimensions
8QLWVPP
195.5
42
PCD 150-163
135.5
126
57
25
58
CABLE GLAND "PG13.5"
179.2
14.5
8
FITTING HOLES
9
20
16
8
FITTING HOLES
163
25
58
Ø164.3
52.1
PCD 186-202
168
222.2
228.5
CABLE GLAND "PG13.5"
58
9
20
2- Ø8 SLOT HOLES
Ø130.5
2- Ø8 SLOT HOLES
QWCD35T/ QWCD35TSD
195.5
42
PCD 150-163
135.5
126
57
25
58
CABLE GLAND "PG13.5"
179.2
14.5
8
FITTING HOLES
9
20
16
8
FITTING HOLES
163
25
58
Ø164.3
52.1
PCD 186-202
168
222.2
228.5
CABLE GLAND "PG13.5"
58
9
20
2- Ø8 SLOT HOLES
Ø130.5
2- Ø8 SLOT HOLES
QWCD50T/ QWCD50TSD
3
※
The channel selection method
using a transistor is the same
as the external contact method,
SOHDVHUHIHUWRWKH¿JXUHRQ
the right.
※
7KHVZLWFK¿JXUHWRWKHULJKW
explains how to wire the exter-
nal
contacts of a signal line
product. If the product is not a
signal line product, use the
channelselectionswitch
attached
inside the product.
Binary input mode
Can select up to
31 sound options
Bit input mode
Can select up to
5 sound options
Bit/ Binary Input Method Depending on
Wiring Method
• %LWLQSXWPRGHXVLQJH[WHUQDOOLQHDOORZV\RXWRVHOHFWRQHRI
¿YHVRXQGRSWLRQVE\VZLWFKLQJRQRQHRIWKHFKDQQHOV
&K&K
7RWDORIVRXQGRSWLRQVDUHFRQ¿JXUDEOH
•
%LQDU\LQSXWPRGHXVLQJH[WHUQDOOLQHDOORZV\RXWRUHFHLYH
PXOWLSOHLQSXWVE\XVLQJWKHFKDQQHOV&K&KWRFRQ¿J
ure one of 31 sound options.
•7RWDORIVRXQGRSWLRQVDUHFRQ¿JXUDEOH
■
Bit Input Mode
■
Binary Input Mode
Sound Selection - Using Internal Switch (Built-in Sound Type)
Wiring Instructions for LC Type
• For built-in sound type, use ‘Sound Channel Selection Switch’ located inside the product in order to select the
W\SHRIVRXQG)RUVRXQGFRQ¿JXUDWLRQFKDUWSOHDVHUHIHUWRSDJHDQG
)RUVWDQGDUGW\SHRQFHWKHXQLWLVSRZHUHGRQOLJKWDQGVRXQGDUHZRUNLQJVLPXOWDQHRXVO\
• External power line8/$:*VT[&PP
• External signal line 8/$:*VTPP
• )RU’&W\SHWKHSRODULW\RIEODFNOLQHLVQHJDWLYH
*Caution
Supplying power to the common line or signal lines may cause
malfunction of the product.
1 2 3 4 5
ON
No. 1 2 3 4 5
0 0 0 0 0 0
1 1 0 0 0 0
2 0 1 0 0 0
3 0 0 1 0 0
4 0 0 0 1 0
5 0 0 0 0 1
0 0 0 0 0 0
1 0 0 0 0 1
2 0 0 0 1 0
29 1 1 1 0 1
30 1 1 1 1 0
31 1 1 1 1 1
Ch 1 Ch 2 Ch 3 Ch 4 Ch 5
COM
Ch1 Ch2 Ch3 Ch4 Ch5
ON(1)
OFF(0)
• LC type product with exposed sound selection signal line is
available upon request. Please refer to the diagram below for
wiring.
EXTERNAL CONTACT
COMMON
POWER
EXTERNAL TRANSISTOR-NPN
COMMON
POWER
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Ch 1
Ch 2
Ch 3
Ch 4
Ch 5
Fuse
5HG R
$PEHU$
*UHHQG
%OXHB
:KLWHW
:KLWHW
%ODFN%.
%ODFN%.
5HG R
$PEHU$
*UHHQG
%OXHB
:KLWHW
:KLWHW
%ODFN%.
%ODFN%. Fuse
4
2-Ø9 HOELS or
2-M8 TAPS
PCD 150-163
2-Ø9 HOELS or
2-M8 TAPS
PCD 186-202
QWCD35T QWCD35TSD
%RG\3&$%6 %RG\3&$%6
PCB
Cable gland
+RUQ3& +RUQ3&
5HVRQDWRU3& 5HVRQDWRU3&
7HUPLQDOEORFN7HUPLQDOEORFN
PCB
Cable gland
SD card slot
■
Parts Denition
Parts Denition / Installation
■
Installation
)LUVWPDNHWDSVRUKROHVWKDWPDWFKWKHSURGXFW
mounting bolts locations on the mounting surface①.
• The mounting hole of this product is 9mm in
GLDPHWHUORQJKROH
• If the tap is machined, fasten the bolt through the
mounting hole of the product.
• When machining a hole, insert the bolt through the
product, insert it into the hole, and tighten the nut
from the opposite side of the mounting surface.
,QVWDOODDWZDVKHUDQGDVSULQJZDVKHUWRWKHEROW
if the product can experience severe vibration and
VKRFN
v7DS0DFKLQLQJ
v+ROH0DFKLQLQJ
- SD cards are sold separately
SD card
Precautions for installation
• In case of outdoor applications, install the product in the upright
position. Do not install the product horizontal or upside-down
positions where water can potentially penetrate into the product
and impact it’s operation.
Left direction Reverse direction Right direction
[Installation]
5
%RG\3&$%6 %RG\3&$%6
PCB
+RUQ3&
5HVRQDWRU3& 5HVRQDWRU3&
PCB
+RUQ3&
QWCD50T QWCD50TSD
- SD cards are sold separately
SD card
Installation Environment and Degree of Protection
• This product is designed for indoor and outdoor use with protection rating of IP66.
• If the product is installed in locations that subject it to excessive dust or water other than the designated IP protection ratings
LQGLFDWHG,3LWPD\FDXVHPDOIXQFWLRQRUGDPDJHWRWKHSURGXFW
• After installing the cable, tighten the cable entry as same level of protection rating of the product and seal it so that dust and moisture
can not penetrate into the product.
)RUIXUWKHULQIRUPDWLRQSOHDVHYLVLWRXUZHEVLWHZZZTOLJKWFRP
■
Installation
2-Ø9 HOELS or
2-M8 TAPS
PCD 150-163
2-Ø9 HOELS or
2-M8 TAPS
PCD 186-202
)LUVWPDNHWDSVRUKROHVWKDWPDWFKWKHSURGXFW
mounting bolts locations on the mounting surface①.
• The mounting hole of this product is 9mm in
GLDPHWHUORQJKROH
• If the tap is machined, fasten the bolt through the
mounting hole of the product.
• When machining a hole, insert the bolt through the
product, insert it into the hole, and tighten the nut
from the opposite side of the mounting surface.
,QVWDOODDWZDVKHUDQGDVSULQJZDVKHUWRWKHEROW
if the product can experience severe vibration and
VKRFN
■
Parts Denition
Parts Denition / Installation
v7DS0DFKLQLQJ
v+ROH0DFKLQLQJ
Cable gland
7HUPLQDOEORFN7HUPLQDOEORFN
Cable gland
SD card slot
6
QWCD35TSD
QWCD50TSD
②
②
④
④
⑤
⑤
①
①
③
③
•
8VHUFDQVDYHVRXQGV03WRWKH6’FDUGDQGDEOHWRVHOHFW
1 sound from 5 saved sounds.
• User can save 5 sounds.
• Available in QWCD35TSD/ QWCD50TSD models.
■ Bit Input - Playing External Sound (SD Card)
%LWLQSXWPHWKRGVRXQGVRXUFHFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0
No sound
1 1 0 0 0 0
&XVWRPVRXQGB[[[PS
2 0 1 0 0 0
&XVWRPVRXQGB[[[PS
3 0 0 1 0 0
&XVWRPVRXQGB[[[PS
4 0 0 0 1 0
&XVWRPVRXQGB[[[PS
5 0 0 0 0 1
&XVWRPVRXQGB[[[PS
ON(1)
OFF(0)
%LQDU\LQSXWPHWKRGVRXQGFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0 No sound
1 0 0 0 0 1 Rel rel rel
2 0 0 0 1 0 Slow Ambulance PI-PO
3 0 0 0 1 1 Oit Oit warning sound
4 0 0 1 0 0 (PHUJHQF\:$8<HOS
5 0 0 1 0 1 Pi- buzzer
6 0 0 1 1 0 7 Short PI. / 1 Long
7 0 0 1 1 1 Pi o Pi o
8 0 1 0 0 0 Phone Ring
9 0 1 0 0 1 Pi- buzzer
10 0 1 0 1 0 Pi pi pi short
11 01011Di o Di o 2 tones buzzer
12 0 1 1 0 0 Oit Oit warning sound
13 0 1 1 0 1 Slow Ambulance PI-PO
14 0 1 1 1 0 Slow Di o Di o
15 0 1 1 1 1 Fast Li o li o
16 1 0 0 0 0 Fire.A-ANG
17 1 0 0 0 1 Fast Ambulance PI-PO
18 1 0 0 1 0 Slow Ambulance PI-PO
19 1 0 0 1 1 Ri ro ri ro warning sound
20 1 0 1 0 0 Repeat Di-o 3 times
21 1 0 1 0 1 Fire.A-ANG
22 1 0 1 1 0 Ambulance PI-PO
23 1 0 1 1 1 Slow Fire.A-ANG
24 1 1 0 0 0 Pi-pi- buzzer low frequency
25 1 1 0 0 1 Pi-pi- buzzer high frequency
26 1 1 0 1 0 Di-di- buzzer high frequency
27 1 1 0 1 1 Di-di- buzzer low frequency
28 1 1 1 0 0 Rising Po-ong
29 1 1 1 0 1 Fast Ambulance PI-PO
30 1 1 1 1 0 Rising frequency
31 1 1 1 1 1 Repeat A-ANG
ON(1)
OFF(0)
Operation Parts Conguration
• Built-in sound type product supports binary input 31 channels.
①
Sound channel selection switch
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡7\SHVDQG&RPELQD
WLRQVRIVRXQGV·
②
Volume dial
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡9ROXPH$GMXVWPHQW·
①
Sound channel selection switch
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡7\SHVDQG&RPELQD
WLRQVRI6RXQGV·
②
Volume dial
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡9ROXPH$GMXVWPHQW·
③
Sound setting switch
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡6HOHFWLQJWKH%XLOWLQ
6RXQGDQG([WHUQDO6RXQG6’&DUG·
④
Play mode setting switch
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡3OD\0RGH6HWWLQJ·
⑤
SD card slot
)RUPRUHLQIRUPDWLRQSOHDVHUHIHUWR3DJH‡6HOHFWLQJDQ6’&DUG
DQG6DYLQJ6RXQG)LOHV·
■ QWCD35T/ QWCD50T(Built-in Sound Type)
■ QWCD35TSD/ QWCD50TSD(SD Card Type-MP3)
QWCD35T
QWCD50T
①
①
②
②
• When playing the built-in sound, select the sound in binary
input mode.
• In binary input mode, you can choose one sound from 31
VRXQGVE\FRQ¿JXULQJWKHFKDQQHOV
• Available in QWCD35T/ QWCD50T/ QWCD35TSD/
QWCD50TSD models.
Sound Type and Combination Manual
■ Binary Input - Playing Built-in Sound
7
②
Volume Dial
Volume Adjustment
• The volume output of this
product is adjustable.
•
7XUQWKHYROXPHGLDOFORFNZLVH
to increase the volume, and
WXUQFRXQWHUFORFNZLVHWR
decrease the volume.
• There will be no sound when
the dial is put at MIN.
VOL.
MIN.MAX.
②
②
③
③
QWCD35TSD
QWCD50TSD
Selection between Built-in Sound and
External Sound (SD Card Type)
• To play built-in sounds, set the sound set-
WLQJVZLWFKWRWKH2))SRVLWLRQ
• To play an external sound on the SD card,
insert the SD card into SD card slot and
VHWWKHVRXQGVHWWLQJVZLWFKWR21
7KHXVHUFDQVDYHVRXQGV03WRWKH6’FDUGDQGDEOHWRVHOHFW
the sound in binary input mode.
• Binary input mode chooses one of the 31 sounds by combining
WKHRQRVZLWFKRIWKHGLHUHQWFKDQQHOVWRWKHDVVRFLDWHGWRQH
•Available on
QWCD35TSD/ QWCD50TSD
models.
■ Binary Input - Playing External Sound (SD Card)
ON(1)
OFF(0)
%LQDU\,QSXW0HWKRG6RXQGVRXUFHFRQ¿JXUDWLRQ
Type of sound
No. 1 2 3 4 5
0 0 0 0 0 0
No sound
1 0 0 0 0 1
&XVWRPVRXQGB[[[PS
2 0 0 0 1 0
&XVWRPVRXQGB[[[PS
3 0 0 0 1 1
&XVWRPVRXQGB[[[PS
4 0 0 1 0 0
&XVWRPVRXQGB[[[PS
5 0 0 1 0 1
&XVWRPVRXQGB[[[PS
6 0 0 1 1 0
&XVWRPVRXQGB[[[PS
7 0 0 1 1 1
&XVWRPVRXQGB[[[PS
8 0 1 0 0 0
&XVWRPVRXQGB[[[PS
9 0 1 0 0 1
&XVWRPVRXQGB[[[PS
10 0 1 0 1 0
&XVWRPVRXQGB[[[PS
11 01011
&XVWRPVRXQGB[[[PS
12 0 1 1 0 0
&XVWRPVRXQGB[[[PS
13 0 1 1 0 1
&XVWRPVRXQGB[[[PS
14 0 1 1 1 0
&XVWRPVRXQGB[[[PS
15 0 1 1 1 1
&XVWRPVRXQGB[[[PS
16 1 0 0 0 0
&XVWRPVRXQGB[[[PS
17 1 0 0 0 1
&XVWRPVRXQGB[[[PS
18 1 0 0 1 0
&XVWRPVRXQGB[[[PS
19 1 0 0 1 1
&XVWRPVRXQGB[[[PS
20 1 0 1 0 0
&XVWRPVRXQGB[[[PS
21 1 0 1 0 1
&XVWRPVRXQGB[[[PS
22 1 0 1 1 0
&XVWRPVRXQGB[[[PS
23 1 0 1 1 1
&XVWRPVRXQGB[[[PS
24 1 1 0 0 0
&XVWRPVRXQGB[[[PS
25 1 1 0 0 1
&XVWRPVRXQGB[[[PS
26 1 1 0 1 0
&XVWRPVRXQGB[[[PS
27 1 1 0 1 1
&XVWRPVRXQGB[[[PS
28 1 1 1 0 0
&XVWRPVRXQGB[[[PS
29 1 1 1 0 1
&XVWRPVRXQGB[[[PS
30 1 1 1 1 0
&XVWRPVRXQGB[[[PS
31 1 1 1 1 1
&XVWRPVRXQGB[[[PS
8
LED(+) (-) AMP(+)
DC INPUT
(10V~30V)
NL
AC INPUT
(100V~240V)
LED(+) (-) AMP(+)
DC INPUT
(10V~30V)
NL
AC INPUT
(100V~240V)
Wiring Instruction for Terminal Block
• 6’FDUGVSHFL¿FDWLRQV
- Use standard SD card.
- Mini SD or Micro SD also can be used
with adaptor.
- SD, SDHC type supported
- Storage capacity : Max. 32GB
&ODVV1RVSHFL¿FDWLRQ
• 3OHDVHVDYHWKH03VRXQG¿OHRQWKH6’FDUGDVVKRZQEHORZ
• &UHDWHDQ‡03B),/(·IROGHURQWKH6’FDUGDQGVDYHWKH03
¿OHLQWKHIROORZLQJ¿OHIRUPDW
• 03¿OHIRUPDW
• :KHQVDYLQJ¿OHVSOHDVHVDYHWKHPLQRUGHU
- Please start saving after formatting the SD card.
• 7KHOHQJWKRIWKH¿OHQDPHPXVWQRWH[FHHGFKDUDFWHUV
23 _ For Elise .mp3
)LOHQDPH8SWRFKDUDFWHUV
6HSDUDWRU7UDFNDQG¿OHWLWOH
7UDFN
B)LUHPS
B(PHUJHQF\PS
B)RU(OLVHPS
B&XFNRRV:DOW]PS
[Example]
SD Card Specications and Sound
Saving Manual
3/$<02’(
1
Bit Input Mode
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds once
)RUDEXLOWLQVRXQGWKHSOD\EDFN
time is about 10 seconds
2
Binary Input Mode
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds once
)RUDEXLOWLQVRXQGWKHSOD\EDFN
time is about 10 seconds
3
Bit Input Hold
3OD\EDFN0RGH
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds continuously
4
Binary Input Hold
3OD\EDFN0RGH
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds continuously
5
Bit Input Sound
Reduction Mode
• Decrease the volume of the selected
channel by 15dB
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds continuously
6
Binary Input Sound
Reduction Mode
• Decrease the volume of the selected
channel by 15dB
3OD\EDFNRQHRIWKHEXLOWLQRU
external sounds continuously
7
Bit Input Sequence
0HPRU\3OD\EDFN
Mode
• When other channel signals are
continuously inputted within 3
seconds after inputting the channel,
the input order is memorized and
SOD\EDFNLQWKHPHPRUL]HGRUGHU
SOD\EDFNWLPHLVVHFRQGV
• The last input channel is played
FRQWLQXRXVO\%LWLQSXWRQO\
8
Test Mode
• In the test mode, the Ch1 of the
built-in sound or the external sound
is automatically played continuously
6ZLWFKEDFNWRDQRWKHUPRGHWRH[LW
test mode
&DQVHOHFWEHWZHHQFKDQQHOLQSXWPHWKRGVELWELQDU\
DQGYDULRXVSOD\EDFNPRGHV
• 8VHDDWVFUHZGULYHUWRURWDWHRQHVSDFHDWDWLPH
UHJDUGOHVVRIWKHGLUHFWLRQRIURWDWLRQ
• Switch 0 and 9 have no function.
Play Mode Setting
0
1
2
3
4
5
6
7
8
9
Play mode switch
Can rotate regardless of
direction
※ setting withdrawal in 3 is SD
• Please wire up the power line into terminal ①.
• Please use ‘O’ type or ‘U’ type wire terminal for safe wiring.
• AC type : Can be wired regardless of polarity.
• ’&W\SH3OHDVHUHIHUWRDERYH¿JXUHDQGFDUHIXOO\IROORZ
the wiring instructions.
■QWCD35T
(Built-in Sound Type)
/ QWCD35TSD
(SD Card Type)
QWCD35T-DC type
QWCD50T-DC type
QWCD35T-AC type
QWCD50T-AC type
■QWCD50T(Built-in Sound Type)/ QWCD50TSD(SD Card Type)
※Applicable cable range :AWG18-AWG26
9
1. Please refer to page 8
‘6’&DUG6SHFL¿FDWLRQVDQG6RXQG
Saving Manual’
WRVHHKRZWRVDYHVRXQG¿OHV
- 6XSSRUWVXSWRXVHUGH¿QHGVRXQGV
2. Insert the SD card into the SD card slot.
3. Set the No. 1 switch of the
sound
setting switch to ON to select
external sound.
4. Use the play mode setting switch to select 1, 3, 5, 7 or 8 mode.
- Mode 8 is a test mode which continuously plays channel 1.
,QWKLVFDVHFKDQQHOVHOHFWLRQLVGLVDEOHG
- For more information, refer to page8
‘Play Mode Setting’.
5.
Use the sound select switch to select the one of the 31 user-
GH¿QHGVRXQGV
- For more information, please refer to page 7
‘Binary Input -
3OD\LQJ([WHUQDO6RXQG6’&DUG
’
.
- )RUH[WHUQDOVLJQDOOLQHW\SH/&SURGXFWVSOHDVHUHIHUWR
page 3
‘Bit/ Binary Input Method Depending on Wiring Method’
.
※Insert SD card → Sound switch setting → Play mode switch
setting → Channel selection
■ When Using an External Sound Source (SD Card) Source in
Binary Input Mode
1. Please refer to page 8
‘6’&DUG6SHFL¿FDWLRQVDQG6RXQG
Saving Manual’
WRVHHKRZWRVDYHVRXQG¿OHV
- 6XSSRUWVXSWRXVHUGH¿QHGVRXQGV
2. Insert the SD card into the SD card slot.
3. Set the No. 1 switch of the sound switch to ON to select external
sound.
- For more information, please refer to page 7
‘Selection between
%XLOWLQ6RXQGDQG([WHUQDO6RXQG6’&DUG7\SH’
4. Use the Play mode setting switch to select 1, 3, 5, 7 or 8 mode.
- Mode 8 is a test mode which continuously plays channel 1.
,QWKLVFDVHFKDQQHOVHOHFWLRQLVGLVDEOHG
- For more information, refer to page8,
‘Play Mode Setting’.
7RVHOHFWDFKDQQHOXVHWKHWHUPLQDOEORFNLQWKHEDFNVLGHRI
WKHSURGXFWWRVHOHFWRQHRIWKHXVHUGH¿QHGVRXQGV
- For more information, please refer to page 5
‘Bit Input - Use
([WHUQDO6RXQG6’&DUG ’
- )RUH[WHUQDOVLJQDOOLQHW\SH/&SURGXFWVSOHDVHUHIHUWR
page 3
‘Bit/ Binary Input Method Depending on Wiring Method’
.
※Insert SD card → Sound switch setting → Play mode switch
setting → Channel selection
■ When Using an External Sound Source (SD Card) in Bit
Input Mode
1. Set the sound setting switch to OFF to select the built-in sound.
- For more information, please refer to page 7
‘Selecting between
Built-in Sound and External Sound’
.
2.
6HOHFWRQHRIPRGHVRUE\XVLQJSOD\PRGHVHWWLQJVZLWFK
- Mode 8 is a test mode and the sound of channel 1 is continuously
SOD\HG,QWKLVFDVHFKDQQHOVHOHFWLRQLVGLVDEOHG
- For more information, please refer to page8,
‘Play Mode Setting’
.
3.
Use the channel selection switch to select one of t he 31 built in sound.
- For more information, please refer to page6,
‘Binary Input - Use
Built-in Sound Source’.
-
)RU([WUDFWHGVRXQGVHOHFWLRQVLJQDOOLQHW\SH/&SURGXFW
refer to page3 ‘Bit/ Binary Input Method According to Wiring
Method’for details of channel selection method.
2. QWCD35TSD/ QWCD50TSD
※Sound switch setting → Play mode switch setting
→ Channel selection
■ When Using a Built-in Sound in Binary Input Mode
Model number Built-in
sound When playing a built-in sound :KHQSOD\LQJDQH[WHUQDOVRXQG6’&DUG
Binary input Bit input Binary input
QWCD35T
QWCD50T 31 types of
sounds Play one of 31 special warning
sounds - -
QWCD35TSD
QWCD50TSD 31 types of
sounds Play one of 31 special warning
sounds Play one of the 5 user-
recorded sounds Play one of the 31 user-
recorded sounds
Operation Method and Setting
1. QWCD35T/ QWCD50T
-
Use ‘Channel Selection Switch’ to select one of the 31 built in
sounds.
-
For more information, see page6 ‘Sound Selection’section.
-
For LC type product, refer to page3 ‘Bit/ Binary Input Method
According to Wiring Method’ section for detailed manual of
channel selection method.
■ When Using a Built-in Sound in Binary Input Mode
Product installation direction
■ Install the product in accordance with the manual. Otherwise rainwater or moisture may penetrate into the product.
ㆍELECTRONIC SOUNDER/SIGNAL HORN
6RXQGHUSDUWVKDOOQRWEHIDFLQJWKHVN\
6RXQGHUSDUWVKDOOQRWEHIDFLQJWKHVN\
ㆍBEACON/SIGNALING LIGHT
3RZHUFRUGLQOHWSDUWVKDOOQRWEHIDFLQJWKHVN\
3RZHUFRUGLQOHWSDUWVKDOOQRWEHIDFLQJWKHVN\
ㆍSIGNAL TOWER LIGHTS
ㆍ+($9<’87<(;3/26,213522)6,*1$/,1*6
※For products with a protection rating of less than IPX4, please install it vertically.
※For products with a protection rating of less than IPX4, please install it vertically.
MEMO
+HDG2FH_6XLWH67;97RZHU*DVDQGLJLWDOUR*HXPFKHRQJX6HRXO.RUHD
7HO7ROOIUHH)D[
)DFWRU\_0XNEDQJUR6DQJGRQJP\HRQ*LPKDHVL*\HRQJVDQJQDPGR.RUHD7HO7ROOIUHH
4OLJKW2YHU6($V6DOHV’HSW_
1DNGRQJGDHUR6DVDQJJX%XVDQ.RUHD(RPJXQJ’RQJ7HO
4OLJKW3XEOLF5HODWLRQV0DUNHWLQJ7HDP2FH_1DNGRQJGDHUR6DVDQJJX%XVDQ.RUHD(RPJXQJ’RQJ7HO
1RUWK)LUVW6WUHHW6XLWH6DQ-RVH&$86$7HO)D[
&KLQD)DFWRU\6KDQJKDL6DOHV2FH_1DQGD5RDG%DRVKDQ$UHD6KDQJKDL&KLQD7HO
-
21
-
6651
-
)D[
-
21
-
6315
-
3929
&KLQD)DFWRU\6LWH4LGRQJ_+DL\DQ5RDG4LGRQJ+LJKWHFK,QGXVWULDO’HYHORSPHQW=RQH4LGRQJ-LDQJVX3URYLQFH&KLQD
7HO
-
513
-
8384
-
)D[
-
513
-
8384
-
9910
3URGXFW2SHUDWLRQ,QTXLU\&XVWRPHU6XSSRUW
<RXFDQH[SHFWSURPSWVHUYLFHLI\RXKDYHH[DFWLQIRUPDWLRQVXFKDVPRGHOQDPHV\PSWRPWHOHSKRQHQXPEHUDQGDGGUHVV
※$//352’8&7352’8&763(&,),&$7,216$1’’$7$$5(68%-(&772&+$1*(:,7+287127,&(72,03529(
5(/,$%,/,7<)81&7,2125’(6,*12527+(5:,6(
+HDGRIILFH6XLWH67;97RZHU*DVDQGLJLWDOUR*HXPFKHRQJX6HRXO.RUHD Postal Code
)DFWRU\0XNEDQJ5R6DQJGRQJ0\HRQ*LPKDH6L*\HRQJVDQJQDP’R.RUHD Postal Code
For your safety
6SHFL¿FDWLRQDQGGLPHQVLRQVOLVWHGLQWKLVFDWDORJXHVXEMHFWWRFKDQJHZLWKRXWQRWLFHIRUSURGXFWTXDOLW\LPSURYHPHQW
7KHQHZHVWSURGXFWLQIRUPDWLRQLVDYDLODEOHRQRXUZHEVLWHZZZTOLJKWFRP
3OHDVHUHDGWKHLQVWUXFWLRQPDQXDODWWDFKHGWRWKHSURGXFWFDUHIXOO\EHIRUHLQVWDOODWLRQDQGXVH
www.qlight.com
EN - QWCD35T - 2303A
This manual suits for next models
3
Table of contents
Other Qlightec Marine Equipment manuals
Popular Marine Equipment manuals by other brands
Boss Audio Systems
Boss Audio Systems MR1308UAB user manual
B&G
B&G Network Series manual
Garmin
Garmin GSD20 Sounder installation instructions
auto maskin
auto maskin Marine Pro 400 Series user manual
Dometic GROUP
Dometic GROUP SeaLand VacuFlush HTS-VG owner's manual
WhisperPower
WhisperPower M-SQ7 installation manual
