OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity: Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material: Aluminium, Steel and Stainless Steel
Size: 440 (L) x 180 (H) mm
Weight: 1,75 Kg
Stroke: 7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1 1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
click C
8
Manual |TP46RHSOIT Manual |TP46RHSOIT
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7 1 9 2 01 8 2 1
2 2
2 3
2 4
2 5
2 6
2 8
2 9
3 0
2 7
3 1
3 2
3 3
3 4
3 5
3 6
3 7
3 9
3 8
4 0
TIOS HR64 PT
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important: after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
104P09002 12 04P00707 23 04P09003 34 04P00725
204A00237 13 04A00217 24 04P09005 35 04P00726
304P00701 14 04P00714 25 04P09007 36 04P00727
404P00704 15 04P00715 26 04P09008 37 04A00240
504P00732 16 04P00716 27 04P09010 39 04P00720
604P00053 17 04P00721 28 04P09011 38 04F00100
704P00702 18 04P00717 29 04P09012 40 04P00733
804P00703 19 04A00218 30 04P09013 42 04P00625
904A00216 20 04P00713 31 04P00722 43 04P00626
10 04P00706 21 04A00219 32 04P00723
11 04P00705 22 04P00622 33 04P00724
unlock
Manual AS R-64-PT Manual AS R-64-PT
AS R-64-PT
OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity: Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material: Aluminium, Steel and Stainless Steel
Size: 440 (L) x 180 (H) mm
Weight: 1,75 Kg
Stroke: 7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1 1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
8
Manual |TP46RHSOIT Manual |TP46RHSOIT
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7 1 9 2 01 8 2 1
2 2
2 3
2 4
2 5
2 6
2 8
2 9
3 0
2 7
3 1
3 2
3 3
3 4
3 5
3 6
3 7
3 9
3 8
4 0
TIOS HR64 PT
2
Manual |TP46RHSOIT
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important: after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
104P09002 12 04P00707 23 04P09003 34 04P00725
204A00237 13 04A00217 24 04P09005 35 04P00726
304P00701 14 04P00714 25 04P09007 36 04P00727
404P00704 15 04P00715 26 04P09008 37 04A00240
504P00732 16 04P00716 27 04P09010 39 04P00720
604P00053 17 04P00721 28 04P09011 38 04F00100
704P00702 18 04P00717 29 04P09012 40 04P00733
804P00703 19 04A00218 30 04P09013 42 04P00625
904A00216 20 04P00713 31 04P00722 43 04P00626
10 04P00706 21 04A00219 32 04P00723
11 04P00705 22 04P00622 33 04P00724
unlock
Manual AS R-64-PT Manual AS R-64-PT
AS R-64-PT
Einstellung des Mundstücks:
Nach der Hubeinstellung ist es wichtig das Mundstück (6) einzustellen
und mit der Kontermutter (5) zu sichern. Ö
Anschlag, Sie hören dann ein Klickgeräusch und die Mechanik ist entriegelt.
Die Blindnietmutter auf den Gewindedorn drehen bis ein Gewindegang
des Gewindedorns am Schaftende der Blindnietmutter übersteht. Dann
das Mundstück (6) bis zum Anschlag gegen den Kopf der Blindnietmutter
drehen. Mit der Kontermutter (5) sichern. Diesen Vorgang bei jedem Wechsel
der Abmessung wiederholen.
Setzen der Blindnietmutter:
Ög, Sie hören dann ein Klickgeräusch
und die Ratschenmechanik ist entriegelt. Die Blindnietmutter auf den
Gewindedorn des Werkzeuges drehen bis zum Anschlag an das Mundstück.
Die aufgeschraubte Blindnietmutter mit dem Werkzeug in das vorbereitete
Loch, entsprechend Vorgaben, stecken. Die Hebel nun schließen, die
Ratschenmechanik ist aktiv rittel, Sie
hören das Klickgeräusch der Mechanik und schließen dann die Hebel ganz.
Dieser Schritt ist entsprechend der Hubzahl zu wiederholen. Anschließend
den Gewindedorn mittels des Drehknopfes (3) herausdrehen. Prüfen Sie den
festen Sitz der Blindnietmutter.
Wichtig: Nach dem Einstellen der Nietmutter dürfen die Hebel nicht
werden, da ansonsten die
Ratschenmechanik ausgeschaltet ist. In diesem Fall wie oben beschrieben
vorgehen.
D
C
2
Handbuch |TP21NHSOIT 7
Handbuch |TP21NHSOIT
7
8
9
10
1 1
1 2
13
1 4
1 5 1 7 1 8
1 6 19
2 0
2 1
22
2 3
24
2 5
2 6
1
3
5
6
4
2
31
3 2
30
3 3
3 8
4 1
4 2
43
4 4
4 5
3 4
3 5
3 6
3 7
3 9
4 0 2 7
2 9
28
TIOS HN12 PT Die markierten Positionen sind Verschleißartikel und unterliegen nicht der Gewährleistung.
104P00950 13 04P00715 25 04P00726 37 04P00960
204A00230 14 04P00716 26 04P00727 38 04P00969
304P00958 15 04P00721 27 04P00972 39 04P00970
404P00704 16 04P00717 28 04P00541 40 04P00971
504P00807 17 04A00218 29 04F00103 41 04A00236
604P00806 18 04P00713 30 04P00904 42 04A00235
704A00231 19 04A00219 31 04F00100 43 04A00234
804P00706 20 04P00816 32 04P00720 44 04A00233
904P00705 21 04P00722 33 04P00968 45 04A00232
10 04P00707 22 04P00723 34 04P00966 47 04P00625
11 04A00217 23 04P00724 35 04P00964 48 04P00626
12 04P00714 24 04P00725 36 04P00962
6 5
click
unlock
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). When the lock nut is taken o, open up the levers
completely until they click. By doing this, the clamping sleeve with Jawset,
pusher, push pin spring, puller assembly and the return spring will be released
from the tool (B1). Cover the items with your hand before doing this, because
due to the force of the spring below, it can come out with some force. Now you
can unscrew the clamping sleeve and change or clean the jaws. Afterwards, re-
assemble by reversing the above procedure. For the reassembling of drawing
B1, just reassemble according to picture B1, and push it back into the tool.
B1
OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity: Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material: Aluminium, Steel and Stainless Steel
Size: 440 (L) x 180 (H) mm
Weight: 1,75 Kg
Stroke: 7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1 1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
click
C
8
Manual |TP46RHSOIT Manual |TP46RHSOIT
1
2
3
4
5
6
7
8
9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
1 7 1 9 2 01 8 2 1
2 2
2 3
2 4
2 5
2 6
2 8
2 9
3 0
2 7
3 1
3 2
3 3
3 4
3 5
3 6
3 7
3 9
3 8
4 0
TIOS HR64 PT
2
Manual |TP46RHSOIT
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important: after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
104P09002 12 04P00707 23 04P09003 34 04P00725
204A00237 13 04A00217 24 04P09005 35 04P00726
304P00701 14 04P00714 25 04P09007 36 04P00727
404P00704 15 04P00715 26 04P09008 37 04A00240
504P00732 16 04P00716 27 04P09010 39 04P00720
604P00053 17 04P00721 28 04P09011 38 04F00100
704P00702 18 04P00717 29 04P09012 40 04P00733
804P00703 19 04A00218 30 04P09013 42 04P00625
904A00216 20 04P00713 31 04P00722 43 04P00626
10 04P00706 21 04A00219 32 04P00723
11 04P00705 22 04P00622 33 04P00724
unlock
