Quadra-Fire LOGS-QFI30FB User manual

1
Quadra-Fire • LOGS-QFI30 Log Instructions • 2221-935 Rev. E • 6/18
Log Set Assembly: LOGS-QFI30FB
Models: QFI30FB, QFI30FB-C, QFI30FB-IFT
LOG PLACEMENT INSTRUCTIONS
Figure 3. Install Glass Rock
Figure 4. Place Log #1 Figure 5. Place Log #2
Figure 1. Logs Installed
GRATE TINES
PILOT BRACKET
LOG PIN
LIGHT TRAYS
GRATE BAR
1
2
5
6
4
3
7
Figure 2. Reference Points for Log Placement
Log #1 (SRV2221-703): Position Log #1 as shown in Figure 4. See Figure 2 for additional points of reference. Center the
log over the pilot bracket. Pull the log forward until contact is made with burner.
Log #2 (SRV2221-701): Position Log #2 as shown in Figure 5. See Figure 2 and Figure 6 for additional points of reference.
The recessed area on the bottom of the log and the back right corner of the burner top mate.
GLASS ROCK
LOG RESTS
AGAINST BACK
OF FIREBOX
CENTER LOG
OVER PILOT
BRACKET
FLAT SPOT
FOR LOG #6
RECESSED
AREA OF LOG
MATES WITH
BURNER TOP
1
2
SRV2221-703
SRV2221-701
SRV2221-704
SRV2221-707
SRV2221-705
SRV2221-706
SRV2221-702
CAUTION: Logs are fragile, handle with care.
Glass Rock (2201-853): Fill each light tray evenly with the glass rock.
WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over
burner ports. Improperly placed glass rock interferes with proper burner operation.

Quadra-Fire • LOGS-QFI30 Log Instructions • 2221-935 Rev. E • 6/182
Log #4 (SRV2221-706): Position Log #4 as shown in Figure 9. See Figure 2 and Figure 10 for additional references. Mate
the grate tine slot with the base of the right grate tine. The grate tine slot is located on the bottom right end of Log #4. See
Figure 10. Slide the right end of the log forward until the tine fully engages the slot. Mate the log pin slot with the right log pin.
Figure 8. Log #3 - Bottom View Figure 9. Place Log #4
MATE LOG PIN
WITH LOG SLOT
Figure 11. Place Log #5
4
Figure 6. Log #2
Log #3 (SRV2221-702): Position Log #3 as shown in Figure 7. See Figure 2 and Figure 8 for additional reference points.
Mate the base of the left grate tine with the groove located on the bottom of the log. Pull the log forward until it stops against
the vertical portion of the grate tine. Swing the rear of the log counterclockwise until it touches the rebox.
FRONT
Figure 7. Place Log #3
RECESSED AREA
2
BACK
FLAT SPOT
FOR LOG #5
LOG TOUCHES
FIREBOX
3
3
BASE OF GRATE TINE FITS IN GROOVE
BASE TINE
MATE GRATE TINE
WITH LOG SLOT
4
Figure 10. Log #4 - Bottom View
GRATE TINE SLOT LOG PIN SLOT
FRONTBACK
FLAT SPOT FOR LOG #6
LOG GROOVE FOR LOG #7
5
Log #5 (SRV2221-704): Position Log #5 as shown in Figure 11. See Figure 2 and Figure 12 for additional references.
Rest the left end of Log #5 on the at spot indicated in Figure 7. Locate right end of log against the grate and to the left of
the log pin. Ensure the nose of the log does not cover any burner ports.
RIGHT
LEFT

3
Quadra-Fire • LOGS-QFI30 Log Instructions • 2221-935 Rev. E • 6/18
6
Log #6 (SRV2221-705): Position Log #6 as shown in Figure 12. See Figures 2, 5 and 11 for additional reference points.
Place the front end of log #6 on the at spot indicated in Figure 11. Place the back end of Log #6 on the at spot indicated
in Figure 5.
Figure 12. Place Log #6
Figure 13. Place Log #7
Log #7 (SRV2221-707): Position Log #7 as shown in Figure 13. See Figure 2 and 11 for additional reference points. Place
the front end of Log #7 on the at spot indicated in Figure 11. Place the back end of Log #7 on the left side of the knot. See
Figure 13.
PLACE END OF LOG
ON FLAT SPOT
PLACE END OF LOG
ON FLAT SPOT
7
PLACE END OF LOG
ON FLAT SPOT
REST END OF LOG
ON THE LEFT SIDE
OF KNOT
KNOT