Quadra-Fire SANTAFE-B1 User manual

R
www.quadrare.com 7001-142D September 1, 2008
SANTA FE PELLET STOVE
Owner’s Manual
Installation and Operation
SANTAFE-B1
Model:
HOT! DO NOT TOUCH.
SEVERE BURNS MAY RESULT.
CLOTHING IGNITION MAY RESULT.
WARNING
• Keep children away.
• CAREFULLY SUPERVISE children in same room as
appliance.
• Alert children and adults to hazards of high
temperatures.
• Do NOT operate with protective barriers open or
removed.
• Keep clothing, furniture, draperies and other
combustibles away.
Glass and other surfaces are hot
during operation and cool down.
WARNING
Please read this entire manual
before installation and use of this
pellet fuel-burning room heater.
Failure to follow these instructions
could result in property damage,
bodily injury or even death.
• Do not store or use gasoline or other am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• Do not overre - If any external part starts to
glow, you are overring. Reduce feed rate.
Overring will void your warranty.
• Comply with all minimum clearances to com-
bustibles as specied. Failure to comply may
cause house re.
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, re ofcials or authorities having
jurisdiction about restrictions, installation inspection,
and permits.
CAUTION
Tested and approved for wood pellets and shelled
eld corn fuel only. Burning of any other type of fuel
voids your warranty.
CAUTION
O-T L
Tested and
Listed by Portland
Oregon USA
OMNI-Test Laboratories, Inc.
CUS
DO NOT DISCARD THIS MANUAL
CAUTION
• Important operating and
maintenance instruc-
tions included.
• Leave this manual with
party responsible for use
and operation.
• Read, understand and
follow these instruc-
tions for safe installa-
tion and operation.
DO NOT
DISCARD

Page 2 7001-142D September 1, 2008
Santa Fe Pellet Stove
R
R
R
Hearth & Home Technologies welcomes you to our tradi-
tion of excellence! In choosing a Quadra-Fire appliance,
you have our assurance of commitment to quality, durabil-
ity, and performance.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum operation of
our stoves, inserts and replaces. And yet we are old-fash-
ioned when it comes to craftsmanship. Each unit is meticu-
lously fabricated and surfaces are hand-nished for lasting
beauty and enjoyment. Our pledge to quality is completed
as each model undergoes a quality control inspection. We
wish you and your family many years of enjoyment in the
warmth and comfort of your hearth appliance. Thank you
for choosing Quadra-Fire.
SAMPLE: CLEARANCE TO COMBUSTIBLES LABEL
LOCATION: Back side of left side panel.
Manufactured
Date
Serial Number
Model Name
Test Lab &
Report No.
Listed Solid Fuel Room Heater/Pellet Type Insert.
Also suitable for Mobile Home
Installation. This appliance has been tested and listed for use in Manufactured Homes
in accordance with OAR 814-23-9000 through 814-23-909.
Tested to: ASTM E1509, ORD-C-1482-M199 0 Room Heating Pellet Burning Type,
APFI, (UM) 84-HUD FOR USE
ONLY WITH PELLETIZED WOOD OR SHELLED FIELD CORN
FUEL.
Input Rating: 30,000 Btu's/hr
Electrical Rating:
115 VAC, 60 Hz, Start 4.1Amps, Run 1.1 AMPS .
Route power cord away from unit. Do not route cord under or in front of appliance.
DANGER:
Risk of electrical shock. Disconnect power supply before servicing. Replace
glass only with 5mm ceramic available from your dealer. To start, set thermostat above
room temperature, the stove will light automatically. To shutdown, set thermostat to below
room temperature. For further instruction refer to owner's manual.
Keep viewing and ash removal doors tightly closed during operation.
U.S. ENVIRONMENTAL PROTECTION AGENCY
This model is exempt from EPAcertification under 40 CFR 60.531 by definition [Wood Heater (A) "Air-to-Fuel Ratio"].
2008 2009 2010 JAN FEB MAR APR MAY JUNE JULY AUG SEPT OCT NOV DEC
7001-143
DO NOT REMOVE THIS LABEL / NEPAS ENLEVER L'ÉTIQUETTE
Made in U.S.A./Fait Aux États-Unis
CAUTION
:
HOT WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN,CLOTHINGAND
FURNITUREAWAY. CONTACTMAYCAUSESKINBURNS. SEENAMEPLATEANDINSTRUCTIONS.
Operatethisunitwithfuelhopperlidclosed.Failuretodosomayresultinemissionsproducts'combustionfromthe
hopper under certain conditions. Maintain hopper seal in good condition. Do no over fill the hopper.
ATTENTION:
CHAUDLORSDE L'OPÉRATION.NE PAS TOUCHER.GARDEZLES ENFANTS ET LES VÊTEMENTSLOIN
DE L'ESPACE DÉSIGNÉDE L'INSTALLATION.LE CONTACT PEUT CAUSERDES BRÛLURESÀ LAPEAU. VOIRL'ÉTIQUETTE
ET LESINSTRUCTIONS.
Opérezcet appareilavecle couverclede la trémiefermé.Le défautde ne passuivreles instructionspeutrésulter,
sous certaines conditions, en une combustion des émissions des produits venant de la trémie. Ne pas remplir la trémie trop pleine.
Testé à: ASTM E1509-95, ORD-C 1482-M1990 Room Heating. Pellet Burning Type, APFI, (UM)
84-HUD POUR USAGE AVEC LES BOULETTES DE BOIS OU DE COMBUSTIBLE DE MAIS ÉCOSSÉ
DES CHAMPS.
Puissance de Rendement:30,000 Btu's/hr
Puissance Électrique: 115 VAC, 60 Hz, Début 4.1Amps, Courir 1.1 Amps,
Éloignez le fil électrique de l'appareil. Ne pas faire passer le fil électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique. Déconnectez le fil électrique de la prise de contact avant le
service.
Remplacez la vitre seulement avec une vitre céramique de 5 mm disponible chez votre fournisseu r.
Pour allumer, monter la température du thermostat au dessus de la température de la pièce, le poêle s'allumera
automatiquement. Pour éteindre, descendre la température du thermostat en dessous de la température de la
pièce. Pour des instructions supplémentaires, référez vous au manuel du propriétaire. Gardez la porte
d'ouverture et la porte des cendres fermées hermétiquement durant l'opération.
Appareil de chauffage inséré de combustible solide/de type de boulettes. Accepté dans l'installation
dans les maisons mobiles. Cet appareil a été testé et enregistré pour l'usage dans les Maisons
Mobiles en accord avec OAR 814-23-9000 jusqu'à 814-23-909.
1445 Highway North
Colville, WA 99114
Manufactured by:Fabriqué par
:
R
Santa Fe Pellet Stove
Report /Rapport
061-S-53-2
SERIAL NO.
/NUMÉRO DU
If Cast Base is installed (Part 811-0840 ) use a noncombustibl e floor
protecto r, extendin g beneath heater and to the front/sides/rea r as
indicated. Measure front distance (I) from the surface of the glass door. If
Cast Base is not installed, the non-combustible floor protector must be 1/4"
(6.4mm) minimum thickness ("k" value = 0.84).
G = 2"/51mm
H* = 2"/51mm
I = 6"/152mm
FLOOR PROTECTION / PROTECTION DU SOL
G
I
*H
G
*
Non-combustible floor protection must extend beneath the flue pipe when
installed with horizontal venting or under the Top Vent Adapter with vertical
installation. RECOMMENDED IN USA; REQUIRED IN CANADA
Installezet utilizeretayagedu fonte(Pièce811-0840),le poêledoitêtreplacésur uneassisenon
combustibles’étendanttoutautourdelui,commelesschémasl’indiquent.Mesurezladistancedu
devant (I) de la surface de la porte vitrée.
Nepasinstallezétayagedufonte leprotecteurdeplancherdoitêtred'unminimumde1/4"(6.4mm)
d'épaisseur, ('k" value = 0.84) de matériel incombustible ou équivalent.
*Un protecteur incombustiblede plancherdoit s'étendre sous le conduitde cheminée
pour une installation de ventilation horizontale ou sous un adapteur de ventilation de
dessus pour une installation verticale. ÉTATS-UNIS-RE COMMANDÉ ; CANAD A -
REQUIREN T.
www.quadrafire.co m
007
O-T L
Tested and
Listed by Portland
Oregon USA
OMNI-Test Laboratories, Inc.
CUS

R
R
R
September 1, 2008 7001-142D Page 
Santa Fe Pellet Stove
Section 1: Listing and Code Approvals
A. Appliance Certications ......................4
B. Mobile Home Approved ......................4
C. Glass Specications ............................4
D. Electrical Rating ..................................4
E. BTU & Efciency Specications ..........4
Section 2: Getting Started
A. Design, Installation & Location
Considerations ....................................5
B. Fire Safety ..........................................5
C. Tools & Supplies Needed ...................6
D. Measuring Standards..........................6
E. Inspect Appliance & Components
and Pre-Use Check List ......................6
Section 3: Dimensions & Clearances
A. Appliance Dimensions ........................7
B. Clearances to Combustibles ...............8
C. Hearth Requirements..........................9
Section 4: Vent Information
A. Chimney & Exhaust Connection .........10
B. Venting Termination Requirements ....10
C. Equivalent Feet of Pipe .......................11
D. Pipe Selection Chart ............................11
Section 5: Venting Systems
A. Alcove .................................................12
B. Through the Wall .................................1
C. Vertical ................................................14
D. Through the Wall & Vertical ................14
E. Masonry ..............................................15
F. Alternate Masonry ...............................15
Section 6: Mobile Home ..................................16
Section 7: Appliance Set-Up
A. Outside Air Kit .....................................17
B. Top Vent Adapter ................................18
C. Log Set Placement ..............................19
D. Grille & Trim Ring Installation .............20
E. Thermostat Installation ........................21
Section 8: Operating Instructions
A. Fuel Size & Material ............................22
B. General Operation Information ...........22
C. Before Your First Fire .........................2
D. Starting Your First Fire ........................2
E. Fire Characteristics .............................2
F. Feed Rate Adjustment .......................2
G. Ignition Cycles ....................................24
H. Frequently Asked Questions...............24
Section 9: Troubleshooting ............................25-27
Section 10: Maintaining & Servicing Appliance
A. General Maintenance & Cleaning .......28-1
B. High Ash Fuel Content Maintenance ..2
C. Blower & Snap Disc #2 Replacement .-4
D. Igniter Replacement ............................5
E. Bafe & Brick Removal .......................5
F. Bafe & Brick Replacement ................6
G. Glass Replacement .............................7
Section 11: Reference Material
A. Component Functions.........................8-9
B. Component Locations .........................40
C. Exploded Drawings .............................41-42
D. Service Parts & Accessories ...............4-44
E. Service & Maintenance Log ................45
F. Warranty Policy ...................................46-47
G. Contact Information .............................48
TABLE OF CONTENTS

Page 4 7001-142D September 1, 2008
Santa Fe Pellet Stove
R
R
R
1Listing and Code Approvals
A. Appliance Certication
C. Glass Specications
E. BTU & Efciency Specications
This appliance is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of
the mobile home oor, ceiling, and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home and use only listed pellet vent Class “L” or
“PL” connector pipe. A Quadra-Fire Outside Air Kit must be
installed in a mobile home installation.
B. Mobile Home Approved
NOTE: This installation must conform with local codes.
In the absence of local codes you must comply with the
ASTM E1509-95, ULC S627-00, ULC/ORD-C-1482-
M1990, (UM) 84-HUD,
D. Electrical Rating
115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps
*BTU output will vary, depending on the brand of fuel you
use in your stove. Consult your Quadra-Fire dealer for
best results.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products,
their specications and/or price without notice.
Particulate Emis-
sions Rating: 0.7 grams/hr
*BTU Output: 8,000 - 0,000 / hr
Heating Capacity: up to 1,500 sq. ft. depending
on climate zone
Hopper Capacity: 52 lbs
Fuel: Wood Pellets or Shelled Corn
Shipping Weight: 240 lbs
Model: Santa Fe Pellet Stove
Laboratory: OMNI Test Laboratories, Inc.
Report No. 061-S-05-2
Type: Solid Fuel Room Heater/Pellet
Fuel Burning Type
Standard: ASTM E1509-95 and ULC
S627-00, ULC/ORD-C1482-
M1990 Room Heater Pellet Fuel
Burning type and (UM) 84-HUD,
Mobile Home Approved.
State of Colorado: Listed 09-1-05

R
R
R
September 1, 2008 7001-142D Page 5
Santa Fe Pellet Stove
2Getting Started
A . Design, Installation & Location
Considerations
1. Appliance Location
Consideration must be given to safety, convenience, trafc
ow, and the fact that the appliance will need a chimney and
chimney connector. It is a good idea to plan your installation
on paper, using exact measurements for clearances and oor
protection, before actually beginning the installation.
If you are not using an existing chimney, place the appliance
in a location to maintain a clear passage for the installation
of any listed and approved pellet venting system. This appli-
ance may be vented vertically or horizontally.
Maintain specied vent clearance to comubstible require-
ments listed by the pellet manufactures venting instructions
and all clearance to combustivles listed in this manual.
Check with your local building code agency before you begin
your installation. Be sure local building codes do not super-
sede UL specications and always obtain a building permit
so that insurance protection benets cannot be unexpectedly
cancelled. If any assistance is required during installation,
please contact your local dealer.
We recommend that a qualied building inspector and your
insurance company representative review your plans before
and after installation.
2. Thermostat Location
The thermostat’s location will have some effect on the
appliance’s operation. When the thermostat is located close
to the appliance, it may require a slightly higher temperature
setting to keep the rest of the house comfortable. If the
thermostat location is in an adjacent room or on a different
oor level, you will notice higher temperatures near the
appliance.
B. Fire Safety
Maintain the designated clearances to combustibles.
Insulation must not touch the chimney. You must maintain
the designated air space clearance around the chimney.
This space around a chimney is necessary to allow
natural heat removal from the area. Insulation in this
space will cause a heat buildup, which may ignite wood
framing. NOTE: Clearances may only be reduced by
means approved by the regulatory authority having
jurisdiction.
To provide reasonable re safety, the following should be
given serious consideration:
1. Install at least one smoke detector on each oor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2. A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
. A practiced evacuation plan, consisting of at least
2 escape routes.
4. A plan to deal with a hopper re as follows:
In the event of a hopper re:
a. Evacuate the house immediately.
b. Notify re department.
CAUTION
• Do NOT connect this unit to a chimney ue servicing
another appliance.
• Do NOT connect to any air distributon duct or system.
Fire Hazard.
WARNING
• Do not operate appliance before reading
and understanding operating instructions.
• Failure to operate appliance properly may
cause a house re.