Quadratec 92034.1008 User manual

The Trusted Source
®
Quadratec®Platform
Mount Bike Rack
TO REDUCE RISK OF SERIOUS I JURY OR PROPERTY DAMAGE:
READ ALL SAFETY MESSAGES A D U DERSTA D ALL I STRUC-
TIO S A D PROCEDURE NOTICES BEFORE ATTEMPTI G TO
I STALL OR USE THIS PRODUCT. FOLLOW ALL I STRUCTIO S
A D WAR I GS WITH PRODUCT & VEHICLE OW ERS MA UAL.
RISK OF EYE I JURY! SAFETY GLASSES MUST BE WOR AT ALL
TIMES WHILE I STALLI G OR MAI TAI I G THIS PRODUCT.
TORQUE A D RECHECK FASTE ERS AFTER 250 MILES A D
FREQUE TLY THEREAFTER. DO OT USE IF DAMAGED.
MAKE CERTAI BICYCLES ARE PROPERLY SECURED BEFORE
DRIVI G O PUBLIC ROADS. FAILURE TO DO SO COULD CAUSE
PROPERTY DAMAGE OR PERSO AL I JURY.
Installation Manual: Designed for Jeep ’76-’19
CJ, YJ, TJ, JK and JL Wrangler Vehicles
#92034.1008
Q_PLATFORM_RACK_INST_A4.qxp_A4 6/10/19 3:51 PM Page 1

The Trusted Source
®
2
TO REDUCE RISK OF SERIOUS I JURY OR PROPERTY DAMAGE:
I STALL ACCORDI G TO I STRUCTIO S. TORQUE A D RECHECK
FASTE ERS AFTER 250 MILES A D FREQUE TLY THEREAFTER.
I SPECT A D DO OT USE RECEIVER/RACK IF DAMAGED.
ALWAYS FOLLOW ALL SAFETY WAR I GS, CAUTIO S A D OTICES
I THE I STALLATIO I STRUCTIO S A D DOCUME TATIO THAT
CAME WITH YOUR BIKE RACK. THIS DOCUME T O LY REFERS TO
BIKE RACK ASSEMBLY A D I STALLATIO .
MAKE CERTAI BICYCLES ARE PROPERLY SECURED BEFORE
DRIVI G O PUBLIC ROADS. FAILURE TO DO SO COULD CAUSE
PROPERTY DAMAGE OR PERSO AL I JURY.
Before You Begin Installation:
Congratulations on your purchase of
Platform Mount Bike Rack for Wrangler
vehicles. When unpacking, check to
make sure all parts are included and
not damaged due to shipping.
If any part is missing or broken, please
call Customer Service at 800-745-6037
as soon as possible.
Regarding Bike Rack Safety: Always
check that the rack and bicycles are
securely mounted on your vehicle.
Failure to do so could cause property
damage or personal injury.
Thank you again for your purchase
and let’s start the installation process.
a hazardous situation which, if not avoided, could result in death or
serious injury. You CA be KILLED or SERIOUSLY HURT if you don’t
follow instructions.
a hazardous situation which, if not avoided, could result in minor or
moderate injury. You CA be moderately HURT and also may suffer
property damage if you don’t follow instructions.
Careful attention is required to this instruction or operation but does
generally not relate to personal injury. Damage to your Quadratec®
product or other property may result if you don’t follow instructions.
A Few Words About Product Safety:
Your Platform Mount Bike Rack is
intended to enhance the utility and
enjoyment of your off road capable
vehicle. Before installation, please take a
moment to review the following safety
information and installation instructions
Important safety information is gener-
ally preceded by one of three signal
words indicating the relative risk o
injury. The signal words mean:
Q_PLATFORM_RACK_INST_A4.qxp_A4 6/10/19 3:52 PM Page 2

3
PARTS LIST:
A) Main ack Assembly Qty 1
B) eceiver Tube Qty 1
C) Crossbars Qty 2
D) Crossbar With Arm Qty 2
E) Tire Holders Qty 2
F) Tire Cradles Qty 2
G) ear Tire Hold Downs Qty 2
H) M10x120 Button Head Bolts Qty 4
I) M10x60 Carriage Bolts Qty 4
J) M10 Flat Washers Qty 12
K) M10 Nylocks Qty 8
L) ½” Button Head Bolts Qty 2
M) ½” Flat Washers Qty 4
N) ½” Nylock Nuts Qty 2
O) M8 Bolts Qty 4
P) M8 Flat Washers Qty 4
PARTS LIST:
Q) M8 Nylock Nuts Qty 4
) Anti- attle Hitch Pin
With Star Washer & Flat Washer Qty 1
S) Clevis Pin Qty 1
T) M6 Cap Screw Qty 4
INCLUDED TOOLS:
V) 5/16” Hex Wrench Qty 1
W) ¾”/13mm/10mm Combo Wrench Qty 1
X) 17mm Wrenches Qty 2
Y) M6 Hex Wrench Qty 1
Z) M5 Hex Wrench Qty 1
REQUIRED TOOLS:
Safety Glasses
Kit Contents and Hardware:
E
E
C
D
D
F
G
I
H
JK
L
M
N
O
PQ
RS
TVW
XXYZ
B
A
C
Q_PLATFORM_RACK_INST_A4.qx _A4 6/11/19 11:14 AM Page 3

The Trusted Source
®
4
ocate the main rack assembly (A), crossbars (C), and crossbars with arms (D).
Position the all the crossbars into the main rack as shown. (FIG2)
Secure each crossbar to the main rack on the horizontal axis with QTY 1 M10x120 Bolt
(H) Qty 2 M10 washers (J), and QTY 1 M10 nylock (K). Secure each crossbar on the ver-
tical axis with QTY 1 M10x60 Carriage bolt (I), QTY 1 M10 washers (J), and QTY 1 M10
nylock (K). Tighten all bolts with provided M6 Hex (Y) & 17mm wrenches (X). (FIG3)
Bike Rack Assembly:
Put on Safety Glasses.
ocate the 2 crossbars (C) and the rear
tire hold downs (G). Slide the rear tire
hold downs onto the crossbars as
shown. (FIG1)
FIG1
FIG2
FIG3
Q_PLATFORM_RACK_INST_A4.qxp_A4 6/10/19 3:52 PM Page 4

The Trusted Source
®
5
Bike Rack Assembly:
Position the receiver tube (B) into the rack
assembly as shown with the supporting
rib facing as shown. Secure the receiver
tube to the main rack with QTY 2
½” button head bolts ( ), Qty 4 ½”washers
(M), and QTY 2 ½” nylock nuts (N).
Tighten the bolts with the provided 5/16
hex key (V) & ¾” wrench (W). (FIG4)
ocate the tire cradles (F) and position
them on the crossbars with tire holders so
that the higher end of the cradle is facing
the middle of the rack as shown. Install
Qty 2 M8 bolts (O) down through each
holder and through the crossbar. Install
QTY 2 M8 washers (P) and Qty 2
M8 nylocks (Q) and tighten them with
the 13mm combo wrench (W). (FIG5)
Install the tire holder (E) onto the
crossbar arm facing the back of the
rack as shown. (FIG6)
Using a M5 Hex Wrench, install (2) M6
cap screws (T) into either the end of the
crossbar arm as shown. Repeat on 2nd
crossbar arm. (FIG7)
Assembly now complete.
See next page for instalation.
FIG4 FIG5
FIG6 FIG7
Note: There are 3 mounting
holes to a omodate
different length bikes.
Q_PLATFORM_RACK_INST_A4.qxp_A4 6/10/19 3:52 PM Page 5