Quadratec 97109.2002 User manual

The Trusted Source
®
READ ALL SAFETY MESSAGES AND UNDERSTAND ALL
INSTRUCTIONS BEFORE ATTEMPTING TO INSTALL THIS
PRODUCT. ALWAYS WEAR SAFETY GLASSES DURING INSTALL.
J3 Hood Mount Light
Bar Mounting Brackets
For 1997-2006 Wrangler TJ Vehicles: #97109.2002
PARTS LIST:
Hood Light Mounting Brackets - QTY 2
T40 Torx Head Bolts & Washers - QTY 6
*Hardware included with J3 lightbar.
REQUIRED TOOLS:
Safety Glasses
5mm Hex/Allen Key
T40 Torx Bit/Socket
Ratchet Driver & Extension
Driver
Passenger
*Hardware included with lightbar.
J3_HMT_TJ_97109_2002_A4.qxp_A4 1/11/18 3:13 PM Page 1
01112018151412

2
The Trusted Source
®
Put on Safety Glasses. With the hood
securely latched in place, locate the
three T40 Torx bolts on both hood
hinges and remove them using a T40
Torx bit and ratchet. (it may be neces-
sary to score the paint around the bolts
using and razor blade to prevent paint
chipping.)
With the Factory bolts removed install
the Driver and Passenger brackets as
shown with the supplied M8 T40 Torx
bolts and nylon washers. Snug but do
not fully tighten the bolts using a T40
Torx bit or key.
Bracket Installation:
J3_HMT_TJ_97109_2002_A4.qxp_A4 1/11/18 3:13 PM Page 2
01112018151413

3
The Trusted Source
®
After loosely installing, carefully check
to make sure the light bar fits snugly
between the two brackets. You may
need to make some minor adjustments.
Fully tighten the T40 fasteners before
installing the light bar.
While supporting the light bar parallel
to the hood install the 6mm socket
headed screw, lock washer and flat
washer through the hole in the bracket
and thread it into the light bar. Install
another 6mm screw, lock washer, and
flat washer into the slot on the bracket.
Continue to support the bar and repeat
on the opposite side. Snug the cap
screws with a 5mm hex key but do not
fully tighten at this time.
Route wires as needed. Please refer to
the light bar and harness instructions
provided with those components. The
slots on both brackets can be used to
secure the wires using the supplied zip
ties.
Adjust the light bar to the desired angle
and then fully tighten all 4 socket
headed screws with a 5 mm hex key.
J3 Lightbar installation is complete.
Lightbar Installation:
J3_HMT_TJ_97109_2002_A4.qxp_A4 4/13/18 3:26 PM Page 3
04132018152645

4
The Trusted Source
®
Quadratec® Exclusive
Three Year Limited Warranty
Your Quadratec®branded accessories are
covered by the following Limited Warranty
provided exclusively by Quadratec, Inc., 1028
Saunders Lane, West Chester PA 19380.
This Limited Warranty is the only warranty
made in connection with your purchase.
Quadratec neither assumes nor authorizes any
vendor, retailer or other person or entity to as-
sume for it any other obligation or liability in
connection with this product or Limited War-
ranty. This Limited Warranty does not apply
and is not cumulative to any accessory or part
distributed by Quadratec for which the Manu-
facturer provides a separate written warranty.
What is Covered: Subject to the terms, exclu-
sions and limitations herein and with respect
only to Quadratec branded accessories first sold
in the United States, Quadratec warrants to the
initial retail purchaser only that your
Quadratec accessory shall be free of defects in
material and workmanship: for a period of
three (3) years from date of retail purchase.
This Limited Warranty is not assignable and
shall terminate upon sale of the vehicle upon
which the Quadratec accessory is installed or
other transfer third persons.
All other warranties are hereby disclaimed, ex-
cept to the extent prohibited by applicable law
in which case any implied warranty of mer-
chantability or fitness for a particular purpose
on this product is limited to 3 year from date of
initial retail sale. Quadratec reserves the rights
to: (a.) require invoice or other proof your ac-
cessory is within the terms of this Limited
Warranty as a condition of warranty service
and, (b.) make future revisions to this product
and Limited Warranty without prior notice or
obligation to upgrade your product.
What is Not Covered:
Your Quadratec Limited Warranty does not
cover products or parts Quadratec determines
to have been damaged by or subjected to:
(a.) installation damage, alteration, modifica-
tion, combination with other parts, failure to
maintain or improper repair or service, (b.) nor-
mal wear & tear, cosmetic damage or damage
from moisture or water immersion, (c.) Acts of
God, accidents, misuse, negligence, inadequate
mounting or impact with vehicle(s), obstacles
or other aspects of the environment, (d.) theft,
vandalism or other intentional damage.
Remedy Limited to Repair/Replacement:
The exclusive remedy provided hereunder shall,
upon Quadratec inspection and at Quadratec’s
option, be either repair or replacement of prod-
uct or parts (new or refurbished) covered under
this Limited Warranty. Customers requesting
warranty consideration should first contact
Quadratec to obtain a RGA number
(610-701-3336). All labor, removal, shipping
and installation costs are customer’s
responsibility.
Other Limitations - Exclusion of Damages -
Your Rights Under State Law:
In consideration of the purchase price paid, nei-
ther Quadratec nor any independent Quadratec
distributor/licensee are responsible for any time
loss, rental costs, or for any incidental, conse-
quential, punitive or other damages you may
have or incur in connection with any part or
product purchased. Your exclusive remedy
hereunder for covered parts is repair/replace-
ment as described above.
This Limited Warranty gives you specific rights.
You may also have other rights that vary from
state to state. For example, some states do not
allow limitations of how long an implied war-
ranty lasts and /or do not allow the exclusion
or limitation of incidental or consequential
damages, so the limitations and exclusions
herein may not apply to you.
©Quadratec, Inc. 2018. All Rights Reserved.
1.11.18 A4 Version
Part #12999.3093
J3_HMT_TJ_97109_2002_A4.qxp_A4 1/11/18 3:13 PM Page 4
01112018151414