Quantum ATL M2500 User manual

Document 6423000-04 A01, May 2003 1
Quantum ATL M2500
Unpacking Instructions
Introduction 3
Removing the Library from the Shipping Carton 3
Removing the Remaining Packing Materials 10
Checking the Contents 21

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
2 6207947-05fN 11

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
Introduction 3
Introduction 0
This document explains how to unpack the ATL M2500 library.
The unpacking procedure consists of the following major steps:
• Removing the library from the shipping carton
• Removing the remaining packing materials
• Checking the contents
Removing the Library from the Shipping Carton 0
To unpack the library:
1The following tools are required for this operation:
•Scissors
•Flatbladescrewdriver
•T-20TORX
®screwdriver
• Antistatic wrist strap
2Place the shipping carton and pallet as close to the installation site
as possible.
Warning: This document is provided as a reference only. This
product requires professional installation by Quantum-
authorized personnel. Non-authorized personnel should
not attempt unpacking or installation. Improper
installation may result in service charges or may
invalidate your product warranty. Please call one of the
following numbers to arrange for professional
installation.
North America: 800-284-5101 or 949-725-2100
Europe: [phone]
Asia/Pacific: [phone]

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
4 Removing the Library from the Shipping Carton
3Carefully cut the two plastic straps securing the shipping carton to
the pallet (see figure 1).
Figure 1 Removing the
Plastic Straps
Caution: The straps are under tension and snap away when
cut.
Straps

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
Removing the Library from the Shipping Carton 5
4Lift the lid off of the shipping carton (see figure 2).
Figure 2 Removing the Lid
from the Shipping Carton
Lid

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
6 Removing the Library from the Shipping Carton
5Cut the adhesive tape securing the upper tray and lift it off (see
figure 3).
6Remove the rack mount shelf box and set it aside (see figure 3).
Figure 3 Removing the
Upper Tray and the Rack
Mount Shelf Box
Rack mount
shelf box
Upper tray

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
Removing the Library from the Shipping Carton 7
7Remove the packing foam from the top of the library and set them
aside (see figure 4).
Figure 4 Removing the
Packing Foam
Packing foam

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
8 Removing the Library from the Shipping Carton
8Fold down the front of the lower tray and remove the front
packaging piece from the lower cushion assembly (see figure 5).
9With the help of another person, remove the library from the pallet
and place it on a level surface (see figure 5).
Figure 5 Removing the
Library from the Pallet
Warning: The library weighs approximately 152 lbs. (69 kg). At
least two people are required to lift and install the
library.
Caution: Lift the library by its sides, not by the front bezel.
Lower tray
Library

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
Removing the Library from the Shipping Carton 9
10 Remove the straps securing the shipping panels to the sides of the
library (see figure 6):
aPull down on the strap tension ratchets to loosen the straps.
bAt the top of the library, unhook the straps.
11 Remove the accessory boxes from the sides of the library and set
them aside (see figure 6).
Figure 6 Removing the
Straps and Accessory
Boxes
12 Remove the shipping panels from the library (see figure 7):
aWith the help of another person, tilt the library to the left
slightly so that the right side of the library lifts up from the
ground approximately 1 in. (25 mm).
bGrip the top of the right shipping panel and pull it away from
the library.
The bottom of the panel disconnects from the bottom of the
library.
Straps
Accessory boxes

Quantum ATL M2500 Unpacking Instructions
Document 6423000-04 A01
May 2003
10 Removing the Remaining Packing Materials
cSet the panel aside.
dRepeat steps 12athrough 12con the other side to remove the
left shipping panel.
Figure 7 Removing the
Shipping Panels
Removing the Remaining Packing Materials 0
Now that you have removed the library from its shipping carton,
remove the remaining packing materials from the library:
1Remove the transit screw from the top of the library and set it aside
(see figure 8).
Later in this procedure you will place the transit screw in a storage
location within the library in case it is needed for future
repackaging and shipment of the library.
Caution: The transit screw secures the library robotics. Do not
try to move the library robotics unless this screw and
the two transit screws securing the X-Y tray
(removed later during this procedure) have been
removed; moving the robotics with the transit screws
in place can cause serious damage to the library.
Shipping panels