Quantum Scalar i40 User manual

www.quantum.com
Scalar i40 and Scalar i80
Scalar i40 and Scalar i80
Quick Start Guide
This quick start guide provides basic installation and configuration
instructions for the Scalar® i40 and Scalar i80 libraries. For more
information, see the
Quantum Scalar i40 and Scalar i80 User’s Guide
located on the documentation CD provided with your library.
This instruction uses the following conventions:
Caution: Cautions indicate potential hazards to equipment and are
included to prevent damage to equipment.
WARNING: Warnings indicate potential hazards to personal safety and
are included to prevent injury.
Scalar i80 Scalar i40
Contents
Required Tools and Equipment .............. 2
Environmental Requirements ................ 2
Taking ESD Precautions .......................... 2
Unpacking the Library............................ 3
Accessory Kit Contents .......................... 5
Installing the Library in a Rack or
Desktop Kit............................................. 5
Installing the Tape Drives ....................... 5
Connecting the Cables........................... 7
Turning the Library ON and Configuring
Network Settings ................................... 8
Accessing the Library Via the Web
Client .................................................... 13
Configuring Partitions.......................... 14
Running the Installation and Verification
Test ....................................................... 14
Importing Tape Cartridges ................... 15
Saving the Library Configuration ........ 17
Configuring the Host Software............ 17
Registering the Library......................... 17

2Required Tools and Equipment
Scalar i40 and Scalar i80 Quick Start Guide
Required Tools and Equipment
• Ethernet cable
Environmental Requirements
The installation site must have the following environmental conditions:
• Humidity 20% – 80% non-condensing
• Temperature: 50°F – 95°F (10°C – 35°C)
• Altitude: –500 to 10,000 feet (–152 to 3048 meters)
These environmental conditions apply when the Scalar i40 and Scalar i80 libraries are in
operation. For additional specifications, refer to the
Quantum Scalar i40 and Scalar i80
User’s Guide
.
In addition, install the library in a location that is as free from dust as possible. Dust can
damage or degrade performance of library components and media.
Taking ESD Precautions
Some components within the Scalar i40 and Scalar i80 libraries contain static-sensitive
parts. To avoid damaging these parts while performing installation procedures, always
observe the following precautions:
• Use an antistatic wrist strap. If you do not have one, touch the outside of the library
on the sheet metal before touching any components to discharge static from your
body.
• Keep static-sensitive parts in their original shipping containers until ready for
installation. Look for the ESD sticker to identify static sensitive parts.
• Avoid touching connectors and other components.
Note: Dry climates and cold-weather heating environments have lower relative
humidity and are more likely to produce static electricity.

Unpacking the Library 3
Scalar i40 and Scalar i80
Unpacking the Library
Note: Unpack the library as close to the installation location as possible.
1Inspect the outer library packaging for damage. If there is any damage evident on
the library packaging, do not continue with the installation and contact Quantum
customer support.
2Open the library packing box and remove the kit tray containing the accessory kit
and rail kit (see Figure 1). Some configurations come with tape drives installed in the
library, and some come with tape drives packaged separately. If yours comes with
tape drives packaged separately, remove them and set aside for installation later.
Figure 1 Packaging
Kit tray
Accessory kit
To p f o a m
Bottom foam
Shipping carton
Rail kit
Media labels
Bottom tray (Scalar i80 only)
Pallet (Scalar i80 only)
Scalar i80
Scalar i40

4Unpacking the Library
Scalar i40 and Scalar i80 Quick Start Guide
3Remove the top foam.
4 Scalar i80 only: Remove the shipping carton by lifting it straight up out of the
bottom tray.
5With the help of a second person, lift the library chassis out of the bottom foam and
place it on a table approximately waist high.
WARNING: Two people are required to safely lift the library out of its packaging
or into a rack.
Caution: Lift the library chassis at the sides. Avoid putting the weight of the
library chassis on the front bezel.
6Remove the anti-static wrapping from the library. Keep the anti-static wrapping
intact so that you can use it later if needed.
7Save the packing box, packaging material, and anti-static wrapping in case you need
to move or ship the library in the future.
8Remove the robot restraint. The robot restraint consists of four (4) thumbscrews, a
plastic sheet, and a small metal clip, located on the top cover of the library. (See
Figure 2.)
aUnscrew and remove the four thumbscrews from the top cover (see Figure 2).
Save the thumbscrews in case you need to move or ship the library in the future.
Note: The robot may stay at the top of the library, or it may move downward
toward the floor of the library. If it moves downward, you will hear the
gears turning as it moves. This is normal.
bRemove the plastic sheet and metal clip and discard. You will not need to use
them again.
Figure 2 Removing the Robot
Restraint
Metal
clip
Plastic
sheet

Accessory Kit Contents 5
Scalar i40 and Scalar i80
9Once you remove the robot restraint, you may cover the holes in the library top
cover with stickers, which are provided in the accessory kit for this purpose. This
step is optional and is intended to prevent small objects from accidentally falling
into the library through the holes.
10 Remove the protective plastic sheet covering the front panel display.
Accessory Kit Contents
• Power cord(s) – one for each power supply
• Scalar i40 and Scalar i80 Documentation and Training CD
• Scalar i40 and Scalar i80 Quick Start Guide
• China RoHS statement
• System, Safety, and Regulatory Information Guide
• Stickers (clear, round) to cover holes in library top cover
Installing the Library in a Rack or Desktop Kit
Follow the instructions that came with your rail kit or desktop kit to install the library.
Installing the Tape Drives
If your library already has tape drives installed, skip this section.
Tape Drive Slot Location
Considerations
Tape drives can only fit in certain slots, as described below and illustrated in Figure 3.
Slots are numbered starting from the bottom and moving up.
•Scalar i40: Half-height tape drives can be installed in slots 1 and 2.
•Scalar i80: Half-height tape drives can be installed in slots 1, 2, 3, 4, and 5.
It is recommended to start installing the tape drives at the bottom slot and work up,
without leaving spaces between.

6Installing the Tape Drives
Scalar i40 and Scalar i80 Quick Start Guide
Figure 3 Acceptable
Installation Locations for
Half-Height Tape Drives
Installation Instructions 1If needed, remove filler plates from the back of the library to make room for the
tape drives. Unscrew the two captive thumbscrews and pull the filler plates out of
the library. Save the filler plates in case you need to use them in the future.
2Unpack the tape drive and tape drive cable.
Caution: The tape drive always resides in a drive sled, and together they are
effectively one unit. Do not remove the tape drive from the drive sled.
3Insert the tape drive into the drive slot. The “shelf” on the bottom of the drive sled
fits into the notch in the library chassis and slides on the plastic guide rails (see
Figure 4). The tape drive must be level to slide in smoothly. At the very end of the
slide, you will feel a slight “click” as the tape drive sled connector connects into its
mating connector in the library chassis.
Figure 4 Installing a Tape Drive
Tape Drive Slot 5
Tape Drive Slot 4
Tape Drive Slot 3
Tape Drive Slot 2 Tape Drive Slot 2
Tape Drive Slot 1 Tape Drive Slot 1
Scalar i40 Scalar i80
Notch in library
chassis
Drive sled “shelf”
slides in notch

Connecting the Cables 7
Scalar i40 and Scalar i80
4Tighten the tape drive’s captive thumbscrews finger tight to secure the tape drive to
the library chassis.
5Install a filler plate over any open tape drive slot. If you need more filler plates,
contact Quantum.
Caution: Filler plates are required to maintain proper library cooling. Do not run
the library with uncovered slots.
Connecting the Cables
Connect the cords and cables as follows (see Figure 5). It is recommended that you leave
some slack in the cables to allow you to perform replacement procedures in the future.
1Connect the tape drive cables from the tape drives to the host.
Note: Cables for full-height Fibre Channel tape drives must be installed in the
LEFT port as you view the installed tape drive from the rear of the library.
Caution: Use care when handling the fibre optic cables. Do not crimp or bend
the cables. Do not exceed the bend radius specified by the
manufacturer.
2Connect an Ethernet cable (not supplied) into the LEFT port on the system control
board (SCB). The right SCB port is for service use only; do not use. Connect the other
end of the Ethernet cable into a live Ethernet jack connected to your network.
3Connect the power supply cord into the power supply connector. Plug the other end
of the cord into a grounded AC outlet.

8Turning the Library ON and Configuring Network Settings
Scalar i40 and Scalar i80 Quick Start Guide
Figure 5 Reinstalled
Components
Turning the Library ON and Configuring Network Settings
Caution: Before turning the library on, make sure you removed the shipping restraint
(4 thumbscrews, mylar sheet, metal clip) from the top of the library!
Otherwise, the library will not initialize. See Figure 2 on page 4.
1Turn the library ON by pressing the power button on the front bezel (see Figure 6).
• The green power LED on the front panel above the power button illuminates,
and the LCD screen turns on. The library goes through a connection and
initialization sequence. This can take 5 to 17 minutes, depending on the size of
your library.
• The status LED on the rear of each drive sled turns green during initialization.
Ethernet
cable in LEFT
SCB port
Power supply cord
Service port –
do not use
Filler plate

Turning the Library ON and Configuring Network Settings 9
Scalar i40 and Scalar i80
Figure 6 Turning on the Library
When initialization completes, the Setup Wizard screen appears on the operator
panel (see Figure 7). The operator panel screen contains a menu bar with operations
that correspond to the four physical buttons below it. The menu operations and
button functions change with each screen.
Figure 7 Setup Wizard – Initial
Screen
2Before proceeding, verify the Ethernet cable is connected and all of your tape drives
are installed.
3Do one of the following:
• To configure basic network settings using the Setup Wizard, press the button
corresponding to Next on the menu bar. You will be guided through a series of
screens where you can accept or change the default configuration settings
(date, time, IP address, licenses, partitions, I/E station slots, and cleaning slots).
Once you accept a setting, you move to the next one. Remember that you can
always change the configuration later if needed.
• To cancel out of the Setup Wizard and begin using the library immediately, press
the button corresponding to Cancel on the menu bar. This accepts the library’s
default configuration, including an IPv4 address assigned by DHCP. The Setup
Wizard will not appear on the operator panel again, but you can change any of
the configuration settings later using the Setup menus on the operator panel or
the Web client. It is easier to configure the library using the Web client, so you
may wish to cancel now. To access the Web client immediately, skip the rest of
this section and go to Accessing the Library Via the Web Client on page 13.
Power LED
Power
button
Navigation/selection
buttons
Menu bar

10 Turning the Library ON and Configuring Network Settings
Scalar i40 and Scalar i80 Quick Start Guide
The Setup Date/Time screen appears (see Figure 8).
Figure 8 Setup Wizard –
Date/Time Screen
4Do one of the following:
• To accept the date and time, press the Accept button.
• To change the date or time, press the Change button. The Date field becomes
available to edit and the menu bar button designations change. Use the Left
and Right buttons to move through the date field, one segment at a time. Use
the Up and Down buttons to change each segment of the date value. You can
press the Up or Down button repeatedly to change the value, or you can hold
the button in for fast scrolling. As you press Right, each segment of the date
fills in. Continue to press the Right button to go to the Time field and edit it the
same way. See Figure 9. When you reach the last segment of the Time field, the
Right button designation changes to Apply. Press the Apply button. The new
date and time display, and you can Accept or Change. Once you press Accept,
you move to the next step.
Figure 9 Changing the Date
and Time
Note: You cannot change the time zone on the operator panel. You can change it
later using the Web client.