Quantum DXi6900 User manual

Quantum DXi6900 Installation Guide
6-68160-03 Rev A, October 2015 *6-68160-03*
Contents
DXi6900 Configuration 2
Determining the DXi6900 Model 4
Choosing a Location 5
Preparing for the Installation 6
DXi6900 Installation Overview 7
Unpacking the DXi6900 10
Installing Components in the
DXi6900 Node 16
Installing the DXi6900 System
in the Rack 32
Initializing the Storage Arrays
and Software 47
Performing Initial Configuration59
Troubleshooting 80
Contacting Quantum 82
This guide provides hardware installation and initial system
configuration instructions for the Quantum DXi6900 disk backup
system. For more information, see the Quantum DXi6900 User's
Guide (6-68159).
Make sure to take the online training for the DXi6900 in order to make
the best use of your product. The online training is available at:
www.quantum.com/ServiceandSupport/StorageCareLearning/Index.aspx
DXi6900 Node
DXi6900 Array Module (RBOD) and Expansion Module (EBOD)
Note: This Installation and Configuration Guide is for DXi6900 with DXi
3.2.x Software.

DXi6900 Configuration
Quantum DXi6900 Installation Guide 2
DXi6900 Configuration
The Quantum DXi6900 can be ordered in the following configurations (see Table 1 below and Table 2 on
the next page).
Table 1: DXi6900 G1 Configurations
DXi6900 G1
Configuration
Licensed
Usable
Capacity**
Nominal
Capacity*
System
Memory
Array
Modules
(RBODs)
Expansion
Modules
(EBODs)
Total
Rack
Space
Required
l1 Node (2U)
l8 x 6 Gb SAS ports
(4 usable)
l4 x 8 Gb Fibre
Channel ports
(ingest and read)
l2 x 8 Gb Fibre
Channel ports (path
to tape, or ingest
and read)
l2 x 10 GbE (SFP+)
Ethernet ports
l3 x 1 GbE Ethernet
ports
l(Optional)
Additional network
adapter providing 2
x 10 GbE (SFP+)
Ethernet ports or 4
x 1 GbE Ethernet
ports
17 TB / 34 TB 48 TB 128 GB 1 0 4U
51 TB / 68 TB 96 TB 128 GB 1 1 6U
85 TB / 102 TB 144 TB 128 GB 1 2 8U
119 TB / 136 TB 192 TB 256 GB 1 3 10U
153 TB / 170 TB 240 TB 256 GB 1 4 12U
187 TB / 204 TB 288 TB 256 GB 1 5 14U
221 TB / 238 TB 336 TB 256 GB 1 6 16U
221 TB / 238 TB 336 TB 256 GB 1 7 18U
255 TB / 272 TB 384 TB 256 GB 2 7 20U
323 TB / 340 TB 432 TB 256 GB 2 8 22U
357 TB / 374 TB 528 TB 256 GB 2 9 24U
391 TB / 408 TB 576 TB 256 GB 2 10 26U
425 TB / 442 TB 624 TB 256 GB 2 11 28U
459 TB / 476 TB 672 TB 256 GB 2 12 30U
493 TB / 510 TB 720 TB 256 GB 2 13 32U
* 1 TB = 1,000,000,000,000 bytes
** Usable storage capacity for installed Array or Expansion modules can be upgraded at any time after purchase in
increments of 17 TB, up to a total of 34 TB per module. Storage capacity upgrades are enabled simply by adding a
license key. To purchase a storage capacity upgrade license, contact your Quantum sales representative. After you
obtain the storage capacity license, refer to the section “Adding a License Key” in the DXi6900 User’s Guide (6-
68159) for instructions on completing the capacity upgrade.

DXi6900 Configuration
Quantum DXi6900 Installation Guide 3
Table 2: DXi6900 G2 Configuration
DXi6900 G2
Configuration
Licensed
Usable
Capacity**
Nominal
Capacity*
System
Memory
Array
Modules
(RBODs)
Expansion
Modules
(EBODs)
Total
Rack
Space
Required
l1 Node (2U)
l4 x 12 Gb SAS
ports
l3 x 1 GbE Ethernet
ports
l(Optional) Up to 6 x
16 Gb Fibre
Channel ports (path
to tape, or ingest
and read)
l(Optional) Up to 6 x
10 GbE (SFP+)
Ethernet ports
l(Optional) Up to 6 x
10 GBase-T
Ethernet ports
17 TB / 34 TB 48 TB 128 GB 1 0 4U
51 TB / 68 TB 96 TB 128 GB 1 1 6U
85 TB / 102 TB 144 TB 128 GB 1 2 8U
119 TB / 136 TB 192 TB 256 GB 1 3 10U
153 TB / 170 TB 240 TB 256 GB 1 4 12U
187 TB / 204 TB 288 TB 256 GB 1 5 14U
221 TB / 238 TB 336 TB 256 GB 1 6 16U
221 TB / 238 TB 336 TB 256 GB 1 7 18U
255 TB / 272 TB 384 TB 256 GB 2 7 20U
323 TB / 340 TB 432 TB 256 GB 2 8 22U
357 TB / 374 TB 528 TB 256 GB 2 9 24U
391 TB / 408 TB 576 TB 256 GB 2 10 26U
425 TB / 442 TB 624 TB 256 GB 2 11 28U
459 TB / 476 TB 672 TB 256 GB 2 12 30U
493 TB / 510 TB 720 TB 256 GB 2 13 32U
* 1 TB = 1,000,000,000,000 bytes
** Usable storage capacity for installed Array or Expansion modules can be upgraded at any time after purchase in
increments of 17 TB, up to a total of 34 TB per module. Storage capacity upgrades are enabled simply by adding a
license key. To purchase a storage capacity upgrade license, contact your Quantum sales representative. After you
obtain the storage capacity license, refer to the section “Adding a License Key” in the DXi6900 User’s Guide (6-
68159) for instructions on completing the capacity upgrade.

Determining the DXi6900 Model
Quantum DXi6900 Installation Guide 4
Determining the DXi6900 Model
Before starting an installation, you will need to determine if the DXi system is a DXi6900 G1 orDXi6900 G2.
DXi6900 model information is located on the pull-out information tag on the front of the Node (see Figure 1
below).
lThe DXi6900 G2 information tag includes “G2” in the part number (see Figure 2 below).
lThe DXi6900 G1 information tag does not include “G1” in the part number (see Figure 3 below).
Figure 1: DXi6900 Information Tag
1
1. Information Tag
Figure 2: DXi6900 G2 Information Tag
Figure 3: DXi6900 G1 Information Tag

Choosing a Location
Quantum DXi6900 Installation Guide 5
Choosing a Location
Quantum recommends installing the system in a controlled or restricted area to prevent access by untrained
personnel. In addition, Quantum recommends that system installation be performed only by qualified IT
personnel.
When choosing an installation site for the DXi6900 system, consider the following requirements:
lInstallation Requirements below
lRack Space Requirements below
lEnvironmental Conditions on the next page
Installation Requirements
Review the DXi6900 Site Planning Guide (6-68161) to ensure that your site meets the installation
requirements for the DXi6900.
Rack Space Requirements
Table 1 below and contains the rack requirements for the DXi6900 components.
Table 1: DXi6900 Rack Requirements
DXi6900 Node Array Module (RBOD) Expansion Module
(JBOD)
Height 2U, 3.4 inches (8.7
cm)
2U, 3.4 inches (8.7 cm) 2U, 3.4 inches (8.7 cm)
Width (side to side) 17.5 inches (44.4 cm) 17.8 inches (45.1 cm) 17.6 inches (44.6 cm)
Depth (front to back) 28.6 Inches (72.6 cm) 21.8 inches (55.2 cm) 21.8 inches (60.2 cm)
DXi6900 G1 Weight (stand
alone)
53.0 pounds (24.0 kg) 59.0 pounds (26.8 +kg) 57.0 pounds (28.4 kg)
DXi6900 G2 Weight (stand
alone)
49.3 pounds (22.4 kg) 59.0 pounds (26.8 +kg) 57.0 pounds (28.4 kg)
Rack Space Required 2U 2U 2U
Air clearance Open 4 in (10.2 cm) behind unit for proper air flow

Preparing for the Installation
Quantum DXi6900 Installation Guide 6
Environmental Conditions
The installation site must have the following environmental conditions:
lHumidity: 20% to 80% (non-condensing) with a maximum humidity gradient of 10% per hour
lTemperature: 10° to 35°C (50° to 95°F) with a maximum temperature gradient of 10°C per hour
lAltitude: –16m to 3048 m (–50 to 10,000 ft)
These environmental conditions apply when the DXi6900 system is in operation. For additional
specifications, refer to the DXi6900 Site Planning Guide (6-68161).
Preparing for the Installation
Before you begin the installation procedure, make the preparations described in the following sections:
lNecessary Tools below
lTaking ESD Precautions below
Necessary Tools
The following tools are required for unpacking and installing the DXi6900 system:
l#2 Phillips screwdriver
lSmall flat head screwdriver
lNotebook computer and Ethernet cable (for initial system configuration)
Taking ESD Precautions
Some components within the DXi6900 system contain static-sensitive parts. To avoid damaging these parts
while performing installation procedures, always observe the following precautions:
lKeep the DXi6900 system turned off during all installation procedures.
lKeep static-sensitive parts in their original shipping containers until ready for installation.
lDo not place static-sensitive parts on a metal surface. Place them inside their protective shipping bag or
on an antistatic mat.
lWear anti-static wrist bands when unpacking and handling the units, and avoid touching connectors and
other components.
Note: Dry climates and cold-weather heating environments have lower relative humidity and are more
likely to produce static electricity.

DXi6900 Installation Overview
Quantum DXi6900 Installation Guide 7
DXi6900 Installation Overview
Depending on the configuration, the DXi6900 system components ship in one or more boxes. Each box
includes a label that notes the number of the box and the total number of boxes in the shipment (for example,
box 1 of 3). MAKE SURE THAT YOU HAVE ALL BOXES IN THE SHIPMENT BEFORE YOU BEGIN
THE INSTALLATION.
Table 1 on the next page provides an overview of the installation process for each DXi6900 configuration.
Locate your configuration in the table to see the components you need to install and the procedures to
follow. YOU MUST INSTALL ALL NODE COMPONENTS, INSTALL THE NODE, ARRAY
MODULES, AND EXPANSION MODULES IN THE RACK, AND CONNECT ALL CABLES BEFORE
FOLLOWING THE POWER UP SEQUENCE.

DXi6900 Installation Overview
Quantum DXi6900 Installation Guide 8
Table 1: DXi6900 Component Installation Overview
DXi6900 Configurations Components to Install Procedures to Complete
17–34 TB 1 DXi6900 Node
1 Array Module (RBOD)
lDXi6900 G1 Options
oDual Port X520 10 GbE Card or
Quad Port i350 1 GbE Card
lDXi6900 G2 Options
oUp to three Dual Port X520 10
GbE Cards
oUp to three Dual Port X540 10
GBase-T Cards
oUp to three 16 GB Fibre Channel
Cards
Note: For all DXi6900 G2 Card
options, see Table 2 on the
next page below.
1. Unpacking the DXi6900 on page
10
2. (Optional) Installing Components
in the DXi6900 Node on page 16
a. Opening the Node Cover on
page 16
b. Installing the Optional
Network Cards on page 25
c. Closing the Node Cover on
page 31
3. Installing the DXi6900 System in
the Rack on page 32
51–102 TB 1 DXi6900 Node
1 Array Module (RBOD)
1 or 2 Expansion Modules (EBODs)
lDXi6900 G1 Options
oDual Port X520 10 GbE Card or
Quad Port i350 1 GbE Card
lDXi6900 G2 Options
oUp to three Dual Port X520 10
GbE Cards
oUp to three Dual Port X540 10
GBase-T Cards
oUp to three 16 GB Fibre Channel
Cards
Note: For all DXi6900 G2 Card
options, see Table 2 on the
next page below.
1. Unpacking the DXi6900 on page
10
2. (Optional) Installing Components
in the DXi6900 Node on page 16
a. Opening the Node Cover on
page 16
b. Installing the Optional
Network Cards on page 25
c. Closing the Node Cover on
page 31
3. Installing the DXi6900 System in
the Rack on page 32

DXi6900 Installation Overview
Quantum DXi6900 Installation Guide 9
DXi6900 Configurations Components to Install Procedures to Complete
119–510 TB 1 DXi6900 Node 16 GB Memory
Module x 8
Card 1 or 2 Array Modules (RBODs)
3 to 13 Expansion Modules (EBODs)
lDXi6900 G1 Options
oDual Port X520 10 GbE Card or
Quad Port i350 1 GbE Card
lDXi6900 G2 Options
oUp to three Dual Port X520 10
GbE Cards
oUp to three Dual Port X540 10
GBase-T Cards
oUp to three 16 GB Fibre Channel
Cards
Note: For all DXi6900 G2 Card
options, see Table 2 below
below.
1. Unpacking the DXi6900 on the
next page
2. (Optional) Installing Components
in the DXi6900 Node on page 16
a. Opening the Node Cover on
page 16
b. Installing the Memory
Modules on page 21
c. Installing the Optional
Network Cards on page 25
d. Closing the Node Cover on
page 31
3. Installing the DXi6900 System in
the Rack on page 32
Table 2: DXi6900 G2 PCI Slot Configuration Options
Caution: The PCI slot location for each card must be followed in each configuration option.
Option PCI Slot 4 PCI Slot 5 PCI Slot 7
101
102 2 x 16 Gb Fibre Channel
103 2 x 16 Gb Fibre Channel 2 x 16 Gb Fibre Channel
104 2 x 16 Gb Fibre Channel 2 x 16 Gb Fibre Channel 2 x 16 Gb Fibre Channel
105 2 x 10 Gb Ethernet *
106 2 x 10 Gb Ethernet * 2 x 10 Gb Ethernet *
107 2 x 10 Gb Ethernet * 2 x 10 Gb Ethernet * 2 x 10 Gb Ethernet *
108 2 x 10 Gb Ethernet * 2 x 16 Gb Fibre Channel
109 2 x 10 Gb Ethernet * 2 x 16 Gb Fibre Channel 2 x 16 Gb Fibre Channel
110 2 x 10 Gb Ethernet * 2 x 16 Gb Fibre Channel 2 x 10 Gb Ethernet *
* 2 x 10 Gb Ethernet = 2 x 10 GbE (SFP+) or 2 x 10 GBase-T Ethernet ports

Unpacking the DXi6900
Quantum DXi6900 Installation Guide 10
Unpacking the DXi6900
By following these unpacking instructions, you help ensure that the system will continue to be safeguarded
after it arrives at the installation site:
lUnpacking the DXi6900 Node on the next page
lUnpacking the Additional Node Components on page 12
lUnpacking the DXi6900Array Module or Expansion Module on page 13
Caution: Make sure to retain all packing materials, as well as the documentation and other items
included in the shipping box. The packaging materials must be used if the system is relocated.
WARNING: The DXi6900 G1 Node (including hard drives) weighs 53.0 pounds (24.0 kg). The
DXi6900 G2 Node (including hard drives) weights 49.3 pounds (22.4 kg). A minimum of two people are
required to lift the chassis.
Unpacking the DXi6900 Node
The box containing the DXi6900 Node contains the following items:
Item Descriiption
Rack mount rails Includes cable management straps.
Accessory kit Includes the following:
lDXi6900 User Essentials
lProduct Installation Instructions card
lQuantum Products Regulatory Documentation CD
lRegistration (Warranty) card
Base Node kit Includes the following:
lC13 to C14 power cord (2)
lNorth American power cord (2)
lCable, CAT6, RJ45, non-plenum, blue solid, 25 feet (3)
Cable kit Fibre Channel HBA Includes the following:
(DXi6900 G1) Cable, 10 GB, 6 meter (6)
(DXi6900 G2) Cable, 12 GB, 6 meter (4)
Node bezel and bezel keys
A network cable kits ships with the Node in a separate box, depending on configuration (see Unpacking the
Additional Node Components on page 12).