Quantum PowerStor L200 User manual

Document 6322502-01, Ver. 1, Rel. 0
February 1999
1
ATL PowerStor L200 Series
Library Unpacking Instructions
Introduction....................................................................................................3
Purpose.....................................................................................................3
Library Configurations ..........................................................................3
Selecting an Installation Location ...............................................................4
Floor Space...............................................................................................4
Overhead Clearance...............................................................................4
Surface Strength and Inclination..........................................................5
Power and Grounding ...........................................................................5
Environmental Specifications ...............................................................5
Unpacking the Library..................................................................................6
Before You Begin.....................................................................................6
Uncrating the Rack-Mount Kit..............................................................6
Installing the Rack-Mount Kit...............................................................6
Uncrating the Library.............................................................................7

ATL PowerStor L200 Series Library Unpacking Instructions
Document 6322502-01, Ver. 1, Rel. 0
February 1999
2

ATL PowerStor L200 Series Library Unpacking Instructions0
Document 6322502-01, Ver. 1 Rel. 00
February 1999
Introduction 3
Introduction 0
Purpose 0The ATL PowerStor L200 Series is an automated storage and retrieval
library system consisting of one DLTTM tape drive and eight DLTtape
cartridges (see figure 1).
This document explains how to unpack the L200 Series library
properly. Once the library is unpacked and moved to the desired
installation location, set up the library using the instructions in the
ATL Powerstor L200 Series Library User’s Guide.
Figure 1 ATL PowerStor
L200 Series Library
Library Configurations 1The L200 Series is shipped in two configurations:
•desktop configuration
•rack-mount configuration

ATL PowerStor L200 Series Library Unpacking Instructions
Document 6322502-01, Ver. 1 Rel. 0
February 1999
4 Selecting an Installation Location
Selecting an Installation Location 1
When selecting an installation location for the library, consider the
following:
•floor space
•overhead clearance
•installation surface strength and inclination
•power and grounding
•environmental specifications
Floor Space 1Figure 2 shows the floor space requirements for setting up and
operating the desktop and rack-mount library.
Figure 2 Floor Space
Requirements
The width of the desktop library is 8.9 inches (22.5 cm). The width of
the rack-mount library is 8.6 inches (21.9 cm). The depth of both
library versions is 22.8 inches (57.8 cm).
Overhead Clearance 2The height of the stand-alone library is 7.6 inches (19.4 cm). The height
of the rack-mount library is 6.9 inches (17.5 cm).
To remove and replace the library enclosure, you need an overhead
clearance slightly greater than the height of the library.
8.9 inches
22.8 inches
Front
Back
(22.5 cm)
(57.8 cm)
8.6 inches
(21.9 cm)
Desktop
Rack-
mount

ATL PowerStor L200 Series Library Unpacking Instructions0
Document 6322502-01, Ver. 1 Rel. 00
February 1999
Selecting an Installation Location 5
Surface Strength and
Inclination 2
Place the library and rack on a clean, level surface. If the library will be
placed on a desk or table, make sure it is sturdy enough to support the
library’s weight (37 lbs/16.8 kg).
Power and Grounding 2The electrical ratings for the library are 100 to 120/200 to 240 VAC, 50/
60 Hertz.
Environmental
Specifications 2
The installation location should meet the following environmental
specifications.
•Temperature: 50°F to 104°F (10°C to 40°C)
•Relative humidity: 20% to 80% noncondensing
•Humidity gradient: 10% per hour
•Dry bulb temperature: 50°F to 104°F (10°C to 40°C)
•Wet bulb temperature: 77°F (25°C)
•Temperature gradient: 19.8°F per hour (11°C per hour) across the
range
•Temperature shock: 18°F (10°C) over two minutes
•Altitude: -500 feet to 30,000 feet (-152.4 meters to 9144 meters)

ATL PowerStor L200 Series Library Unpacking Instructions
Document 6322502-01, Ver. 1 Rel. 0
February 1999
6 Unpacking the Library
Unpacking the Library 2
Unpack the library as close to the installation location as possible.
The unpacking instructions vary depending upon whether you
received a desktop or rack-mount library. If you received a desktop
library, you should have only one shipping carton. Follow the
instructions in “Uncrating the Library” on page 7 to unpack the
library.
If you received the rack-mount library, you will have two shipping
cartons. The large carton contains the library, and the smaller carton
contains the rack-mount kit.
To unpack and install the rack-mount library, you must:
•Uncrate the rack-mount kit and verify its contents (see “Uncrating
the Rack-Mount Kit”).
•Install the rack-mount kit in the rack (see “Installing the
Rack-Mount Kit”).
•Uncrate the library and place it in the rack (see “Uncrating the
Library”).
Before You Begin 2Inspect the shipping pallet and carton for damage that may have
occurred during shipment. Report any damage to the shipper
immediately.
Uncrating the
Rack-Mount Kit 2
Cut the packing tape at the top of the shipping carton and unpack the
rack-mount kit. Before installing the rack-mount kit in the rack,
compare the contents of the carton with the packing list inside the
shipping carton.
Installing the
Rack-Mount Kit 2
Install the rack-mount kit in the rack, referring to the drawing
provided in the shipping carton.

ATL PowerStor L200 Series Library Unpacking Instructions0
Document 6322502-01, Ver. 1 Rel. 00
February 1999
Unpacking the Library 7
Uncrating the Library 2To uncrate an ATL PowerStor L200 Series library:
Procedure
1Cut the straps that secure the shipping carton to the pallet (see
figure 3).
2Lift the carton off of the pallet.
Caution: The library weighs 37 lbs (16.8 kg). Two people should
perform any procedure that involves lifting or moving the
library.
3Open the top of the shipping carton by carefully cutting the
packing tape.
Figure 3 Removing the
Shipping Carton from the
Pallet
4Remove the accessory kit from the carton (see figure 4).
Straps
Pallet
Packing tape
Shipping carton

ATL PowerStor L200 Series Library Unpacking Instructions
Document 6322502-01, Ver. 1 Rel. 0
February 1999
8 Unpacking the Library
Figure 4 Removing the
Accessories Boxes
Procedure (continued)
5Remove the packing foam from the top of the library (see figure 5).
6With two people lifting the library, remove it from the shipping
carton.
7Remove the library from the shipping bag.
8Place the library in the installation location. If it is a rack-mount
library, place it in the rack.
Accessory kit

ATL PowerStor L200 Series Library Unpacking Instructions0
Document 6322502-01, Ver. 1 Rel. 00
February 1999
Unpacking the Library 9
Figure 5 Removing the
Library from the Shipping
Carton
The library is now unpacked. Refer to the ATL PowerStor L200 Series
Library User’s Guide for information about connecting the library cables
and operating the library.
Packing foam
Shipping bag
Library