Quantum Scalar i6000 User manual

User’s Guide
Scalar i6000
6-66879-07 Rev A

ii Quantum Scalar i6000 User’s Guide
Quantum Scalar i6000 User’s Guide, 6-66879-07 Rev A, May 2013, Product of USA.
Quantum Corporation provides this publication “as is” without warranty of any kind, either express or
implied, including but not limited to the implied warranties of merchantability or fitness for a particular
purpose. Quantum Corporation may revise this publication from time to time without notice.
COPYRIGHT STATEMENT
© 2013 Quantum Corporation. All rights reserved.
Your right to copy this manual is limited by copyright law. Making copies or adaptations without prior
written authorization of Quantum Corporation is prohibited by law and constitutes a punishable
violation of the law.
TRADEMARK STATEMENT
Quantum, the Quantum logo, DLT, DLTtape, the DLTtape logo, SuperLoader, Scalar, StorNext, and DXi are
registered trademarks of Quantum Corporation, registered in the U.S. and other countries.
Preserving the World's Most Important Data. Yours., Backup. Recovery. Archive. It’s What We Do., the
DLT logo, DLTSage, Dynamic Powerdown, FastSense, FlexLink, GoVault, MediaShield, Optyon, Pocket-
sized. Well-armored, SDLT, SiteCare, SmartVerify, StorageCare, Super DLTtape, and Vision are trademarks
of Quantum.
LTO and Ultrium are trademarks of HP, IBM, and Quantum in the U.S. and other countries. All other
trademarks are the property of their respective companies.
Specifications are subject to change without notice.

Quantum Scalar i6000 User’s Guide iii
Contents
Preface ix
Chapter 1 Description 1
Front View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Hardware Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Dual Robotics Configurations and Parking Modules . . . . . . . . . . . . . . . 6
Control Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Expansion Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Library Management Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
I/O Management Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Robot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Import/Export Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Cartridge Magazines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Tape Drives and Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Mixed Media Support and Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Support for WORM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Contents
iv Quantum Scalar i6000 User’s Guide
Operator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Power System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Library Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Chapter 2 Troubleshooting Your Library 37
How Does the Library Report Issues?. . . . . . . . . . . . . . . . . . . . . . . . . . 37
Working With Tickets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Interpreting LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
Working With Command History Logs. . . . . . . . . . . . . . . . . . . . . . . . 109
Accessing Online Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Chapter 3 Configuring Your Library 117
Running the Setup Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Enabling Licenses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Working With Partitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Configuring Control Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
Setting Up the Network Configuration . . . . . . . . . . . . . . . . . . . . . . . 161
Managing Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
Setting Up Policies for the Physical Library . . . . . . . . . . . . . . . . . . . . 177
Specifying the Date and Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Configuring E-mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183
Setting Up E-mail Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Setting Up Media Security Notifications . . . . . . . . . . . . . . . . . . . . . . 191
Configuring Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Configuring Drive SCSI ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
Configuring Fibre Channel Drive Speed, Topology, and Loop ID . . . . 197
Configuring Fibre Channel I/O Blades . . . . . . . . . . . . . . . . . . . . . . . . 199
Generating the Library Configuration Report . . . . . . . . . . . . . . . . . . 220

Contents
Quantum Scalar i6000 User’s Guide v
Configuring Drive Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
Registering SNMP Traps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Configuring Library Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Using LDAP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
Configuring Screen Saver Preferences . . . . . . . . . . . . . . . . . . . . . . . . 241
Working With Data Path Conditioning . . . . . . . . . . . . . . . . . . . . . . . 243
About the Configuration Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Setting Aisle Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 246
Configuring a Webcam For Your Library . . . . . . . . . . . . . . . . . . . . . . 247
Working with Towers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
Chapter 4 Active Vault 251
About Active Vault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Configuring Active Vault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Chapter 5 Advanced Reporting 259
Media Usage Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Viewing Cross-Partition Media Moves . . . . . . . . . . . . . . . . . . . . . . . . 262
Chapter 6 Automated Media Pool 265
Requirements for Automated Media Pool . . . . . . . . . . . . . . . . . . . . . 266
Configuring Automated Media Pool . . . . . . . . . . . . . . . . . . . . . . . . . 267
Using Automated Media Pool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
Chapter 7 Capacity on Demand 277
Chapter 8 Encryption Key Management 279

Contents
vi Quantum Scalar i6000 User’s Guide
Encryption Key Management Systems . . . . . . . . . . . . . . . . . . . . . . . . 279
KMIP-compliant Encryption Key Management. . . . . . . . . . . . . . . . . . 281
FIPS-Certified Encryption Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
Setting up EKM on the Scalar i6000 . . . . . . . . . . . . . . . . . . . . . . . . . 285
Using EKM Path Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304
Monitoring EKM Server Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
Using Q-EKM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 307
Using SKM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Chapter 9 Extended Data Lifecycle Management 319
About EDLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Configuring EDLM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Running Manual EDLM Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
Viewing EDLM Test Sessions and Report Details . . . . . . . . . . . . . . . . 340
Diagnosing a Suspect EDLM Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . 348
Chapter 10 Storage Networking 349
Using the Storage Networking Wizard . . . . . . . . . . . . . . . . . . . . . . . 350
Licensing Drives for Storage Networking. . . . . . . . . . . . . . . . . . . . . . 351
Configuring Control Path Failover . . . . . . . . . . . . . . . . . . . . . . . . . . . 353
Configuring Data Path Failover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 359
Configuring Host Access to Storage Networking Drives and Partitions . .
362
Chapter 11 Configuring Access to StorNext 397
Chapter 12 Partition Utilization Reporting 405

Contents
Quantum Scalar i6000 User’s Guide vii
Chapter 13 Running Your Library 411
Logging On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
Connecting to Multiple Libraries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 416
Operator Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 417
Library Management Console (LMC). . . . . . . . . . . . . . . . . . . . . . . . . 420
Understanding Location Coordinates . . . . . . . . . . . . . . . . . . . . . . . . 437
Viewing the Library (Physical or Partition) . . . . . . . . . . . . . . . . . . . . . 448
Changing the Library’s State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450
Working With Local User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . 452
Shutting Down/Rebooting the Library . . . . . . . . . . . . . . . . . . . . . . . . 460
Powering Off the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
Powering On the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 462
Locking/Unlocking the I/E Station . . . . . . . . . . . . . . . . . . . . . . . . . . . 463
When Robotics Are Not Ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
Using the Library Access Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
Chapter 14 Using the Command Line Interface 473
Logging on to the CLI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474
Command Line Interface (CLI) Commands. . . . . . . . . . . . . . . . . . . . . 475
Chapter 15 Maintaining Your Library 491
Monitoring the Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 492
Maintenance Actions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 527
Using Sift Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 652
Retrieving MIBs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 656
Maintaining Air Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 658
Performing Robot and Power Rail Health Checks. . . . . . . . . . . . . . . . 661

Contents
viii Quantum Scalar i6000 User’s Guide
Chapter 16 Working With Cartridges and Barcodes 663
Handling Cartridges Properly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 664
Write-Protecting Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 665
Barcode Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 666
Installing Barcode Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 667
Using Cleaning Cartridges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 669
Managing and Moving Media . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 670

Quantum Scalar i6000 User’s Guide ix
Preface
This guide contains information and instructions necessary for the
normal operation and management of the Scalar®i6000 library. This
guide is intended for system administrators, operators, or anyone
interested in learning about or using the Scalar i6000 library after its
initial installation and configuration. Be aware that you must have
administrator privileges to use many of the features that this guide
describes.
Caution: Be sure to read all operating instructions in this manual
and in the
System, Safety, and Regulatory Information
Guide before operating this product.
Product Safety Statements
This product is designed for data storage and retrieval using magnetic
tape. Any other application is not considered the intended use.
Quantum will not be held liable for damage arising from unauthorized
use of the product. The user assumes all risk in this aspect.
This unit is engineered and manufactured to meet all safety and
regulatory requirements. Be aware that improper use may result in

Preface
xQuantum Scalar i6000 User’s Guide
bodily injury, damage to the equipment, or interference with other
equipment.
Caution: Be sure to read all operating instructions in this manual
and in the
System, Safety, and Regulatory Information
Guide before operating this product.
WARNING: Before powering on or using this equipment, read THE
System, Safety, and Regulatory Information Guide . Keep
the Guide for future reference.
Note: When drive sled positions are empty, drive cover plates must be
installed and in place at all times to prevent access into the
empty drive sled Positions.
Mechanical Locks The access and service doors can only be opened with a key. The key
should be kept by an authorized person at your company. Access to the
interior of the library is both a data-integrity and safety issue.
Power Button on the
Library’s Indicator Panel
Switching off the Power button on the indicator panel, located on the
front of the library, removes power from the electronics, which causes
the picker to stop immediately. This button also removes power from
the drives.
WARNING: This power button functions as a power interrupt only. To
completely remove all power before servicing or in an
emergency, turn off the circuit breaker on the power
distribution unit, and then disconnect the power cord
from the electrical source.
Mercury Statement Projectors, LCD displays, and some multifunction printers may
use lamp(s) that contain a small amount of mercury for
energy-efficient lighting purposes. Mercury lamps in these
products are labeled accordingly. Please manage the lamp

Preface
Quantum Scalar i6000 User’s Guide xi
according to local, state, or federal laws. For more information, contact
the Electronic Industries Alliance at www.eiae.org. For lamp-specific
disposal information check www.lamprecycle.org.
Disposal of Electrical
and Electronic
Equipment
This symbol on the product or on its packaging
indicates that this product should not be disposed of
with your other waste. Instead, it should be handed
over to a designated collection point for the
recycling of electrical and electronic equipment. The
separate collection and recycling of your waste
equipment at the time of disposal will help to
conserve natural resources and ensure that it is
recycled in a manner that protects human health and
the environment. For more information about where you can drop off
your waste equipment for recycling, please visit our Web site at: http://
qcare.quantum.com or contact your local government authority, your
household waste disposal service or the business from which you
purchased the product.
Product Model Number
The Scalar i6000 Regulatory Model Number is as follows:
SCi6000.
Explanation of Symbols and Notes
The following symbols appear throughout this document to highlight
important information.
Note: Indicates important information that helps you make better
use of your system.

Preface
xii Quantum Scalar i6000 User’s Guide
Caution: Indicates a situation that may cause possible damage to
equipment, loss of data, or interference with other
equipment.
WARNING: Indicates a potentially hazardous situation which, if not
avoided, could result in death or bodily injury.
Other Documents you Might Need
The following documents are also available for this product. These
documents can be found on the product CD or at www.quantum.com/
support.
• Scalar i6000 Planning Guide (6-66882-xx)
• Scalar i6000 Release Notes i8 (6-66883-xx)
• Scalar i2000/i6000 Maintenance Guide (6-66880-xx)
• Scalar i6000 Installation Guide (6-66881-xx)
• Scalar i6000 Unpacking Instructions (6-00771-xx [Gen 1] or 6-
67467-01-xx [Gen 2])
• System, Safety, and Regulatory Information Guide ( 6-00618-xx)
Note: Release Notes are also available for this product. The Release
Notes describe changes to your system or firmware since the
last release, provide compatibility information, and discuss any
known issues and workarounds. The Release Notes can be
found in the product box or at www.quantum.com/support.

Preface
Quantum Scalar i6000 User’s Guide xiii
Contacts
Quantum company contacts are listed below.
Quantum Corporate Headquarters
To order documentation on the <Product Name> or other products
contact:
Quantum Corporation (Corporate Headquarters)
1650 Technology Drive, Suite 700
San Jose, CA 95110-1382
Technical Publications
To comment on existing documentation send e-mail to:
[email protected]
Quantum Home Page
Visit the Quantum home page at:
http://www.quantum.com
Getting More Information or Help
StorageCare™, Quantum’s comprehensive service approach, leverages
advanced data access and diagnostics technologies with cross-
environment, multi-vendor expertise to resolve backup issues faster and
at lower cost.
Accelerate service issue resolution with these exclusive Quantum
StorageCare services:
•Service and Support Website - Register products, license software,
browse Quantum Learning courses, check backup software and
operating system support, and locate manuals, FAQs, firmware

Preface
xiv Quantum Scalar i6000 User’s Guide
downloads, product updates and more in one convenient location.
Benefit today at:
http://www.quantum.com/ServiceandSupport/Index.aspx
•eSupport - Submit online service requests, update contact
information, add attachments, and receive status updates via
e-mail. Online Service accounts are free from Quantum. That
account can also be used to access Quantum’s Knowledge Base, a
comprehensive repository of product support information. Sign up
today at:
http://www.quantum.com/osr
•StorageCare Guardian - Securely links Quantum hardware and the
diagnostic data from the surrounding storage ecosystem to
Quantum's Global Services Team for faster, more precise root cause
diagnosis. StorageCare Guardian is simple to set up through the
internet and provides secure, two-way communications with
Quantum’s Secure Service Center. More StorageCare Guardian
information can be found at:
http://www.quantum.com/ServiceandSupport/Services/
GuardianInformation/Index.aspx
For further assistance, or if training is desired, contact the Quantum
Customer Support Center:
United States 800-284-5101 (toll free)
949-725-2100
EMEA 00800-4-782-6886 (toll free)
[phone]
APAC [phone] (toll free)
[phone]
For worldwide support:
http://www.quantum.com/ServiceandSupport/Index.aspx

Quantum Scalar i6000 User’s Guide 1
Chapter 1
Description
The Scalar i6000 library automates the retrieval, storage, and control of
tape cartridges. Application software on the host can use the library’s
robotics to mount cartridges into tape drives and retrieve them without
operator intervention.
The library can be installed on a solid or raised floor. It has a standard
19-inch rack footprint and can be placed in a standard server rack space.
Because the library provides access by way of the access and service
doors, the library can be placed with either side against a wall or
between racks.
In December, 2011, the library robotics were redesigned. The redesign
accommodates either a single robot or dual robotics. The original robot
hardware is referred to as Gen 1; the new robot hardware is referred to
as Gen 2.
With firmware version i11, robots in a dual-robot system work in an
active/active manner, where both robots perform move commands and
other library operations .
Dual robotics libraries require special modules on either end called
parking modules, which house the robots when not in use. See Dual
Robotics Configurations and Parking Modules on page 6 for more
information.
You can tell which generation robot you have via the library user
interface. The library displays which generation of robot hardware is
installed. Select Monitor > System from the menu, click the Robot tab,
and look in the Generation column (see Figure 1).

Chapter 1: Description
2Quantum Scalar i6000 User’s Guide
Figure 1 Robot Tab
For Gen 1 systems, the maximum library can be configured to
accommodate from 100 LTO cartridges to 5,322 LTO cartridges (for a
single-robot library) or 5,376 LTO cartridges (for a dual-robot library).
For Gen 2 systems, the maximum library can be configured to
accommodate from 100 LTO cartridges to 7,146 LTO cartridges (for a
single-robot library) or 7,224 LTO cartridges (for a dual-robot library).
In March of 2013, a High Density Expansion Module (HDEM) was made
available to provide increased storage capabilities. A single HDEM can
hold up to 720 total slots; 540 on two independent carrousels and 240
on the front door.
This chapter provides a description of the following features and
components:
Note: The library software features described in this guide apply to
both the Scalar i2000 and the Scalar i6000. However, certain
features are available on Scalar i6000 only.
This chapter includes the following sections:
•Front View on page 4
•Hardware Configuration Options on page 5
•Dual Robotics Configurations and Parking Modules on page 6
•Control Module on page 9
•Expansion Modules on page 11
•Library Management Module on page 14

Chapter 1: Description
Quantum Scalar i6000 User’s Guide 3
•I/O Management Unit on page 16
•Robot on page 19
•Import/Export Stations on page 19
•Cartridges on page 22
•Cartridge Magazines on page 23
•Tape Drives and Media on page 26
•Mixed Media Support and Rules on page 28
•Support for WORM on page 29
•Operator Panel on page 30
•Power System on page 31
•Library Features on page 31

Chapter 1: Description
Front View
4Quantum Scalar i6000 User’s Guide
Front View
Figure 2 shows a front view of the library, consisting of a control
module and an expansion module.
Figure 2 Front View of a
Control Module and Expansion
Module
control module
expansion module
touch screen
I/E station
access doors
operator panel

Chapter 1: Description
Hardware Configuration Options
Quantum Scalar i6000 User’s Guide 5
Hardware Configuration Options
The library is designed for ease of installation, configuration, and field
upgrades. The minimum library configuration consists of one control
module. You can add up to 15 expansion modules as storage and tape
drive requirements change.
Note: Expansion modules in positions nine through sixteen are no
longer storage-only modules and can contain I/E stations or
drives.
For LTO, the maximum library configuration can accommodate
•1controlmodule,
• 0 to 15 expansion modules
• Gen 1 systems: 100 to 5322 cartridges (single robotics)
• Gen 2 systems: 100 to 7146 cartridges (single robotics), or 100 to
7224 (dual robotics). For libraries containing high-density expansion
modules, the maximum capacities are 12,006 LTO cartridges (for a
single-robot library) or 11,760 LTO cartridges (for dual-robot
libraries).
• 1 to 96 tape drives.
An LTO library I/E Station configuration can accommodate:
• 1 to 8 24-slot Import/Export (I/E) stations in the control module and
first 7 expansion modules.
Or
• 1 24-slot I/E in the control module and up to 7 72-slot I/E stations
and first 7 expansion modules.

Chapter 1: Description
Dual Robotics Configurations and Parking Modules
6Quantum Scalar i6000 User’s Guide
Dual Robotics Configurations and Parking Modules
A dual robotics library requires Gen 2 robotics hardware. A dual robotics
library requires, at a minimum, a control module, a left parking module,
and a right parking module. See Figure 3.
The left and right parking modules have the same size and appearance
as expansion modules, but they function differently. Each parking
module contains a “parking space” in which the respective left or right
robot resides when not in use. The “parking space” occupies four
magazine columns which cannot be used for storage.
The left parking module is located to the left of the control module in
position zero. It is referred to in the user interface as “module 0.” The
left parking module does not contain tape drives, I/E stations, or power
supplies. The control module supplies its power. If you are upgrading to
dual robotics, you will receive a left parking module to add onto your
existing system. This increases your system size, so you must take this
into account when planning for an upgrade.
The right parking module is the right-most module in the system. As of
firmware version i11, a right parking module can contain drives in any
position in the library and up to one 24-slot I/E station. Right parking
modules may not contain 72-slot I/E stations.
Note: HDEMs cannot be used as right parking modules.
If you are upgrading a single-robotics library to a dual-robotics library,
the existing right-most expansion module can, in most cases, be
converted into a right parking module. However, if the existing right-
most expansion module contains a 72-slot I/E station, you may need
another module to be added to the right of your system which will
become the right parking module. If space considerations prohibit the
addition of another module, then the right-most module will be
swapped with another module in the library that does not contain a
72-slot I/E station.