Quoizel BDS8410AGV User manual

Package Contents
Warnings and Cautions
1of3
For Style BDS8410AGV
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBaseBulbs60WMaximum,CandelabraBaseVintageBulbsarerecommended,bulbsnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Fixture Body
x1
C
Installation Guide #IS-BDS8410AGV
2018 QuoizelInc. ReleasedDate:2018-09-18
visit us on-line at www.quoizel.com
B
Alternate
Mounting screw
x2
F
Lock screw
x2
Glass Panel
x4
D
Cage
x1
E
STEP 1 Install Glass Panel-
A. Insert the Glass Panel (F) into
the slot in the bottom edge of the
Cage (E) and press the tabs on
the top edge of the Cage (E) onto
the top edge of the Glass Panel
(F)tosecureit.
F
Slot
Tab
Figure 1
Figure 2
STEP 2 Install Cage with Glass Panels to Fixture Body-
A. Place the Cage (E) over the sockets. Align the tabs in the top edge of
the Cage (E) to the tabs in the fixture hood on the Fixture Body (D).
Secure by threading Lock Screws (C) onto the tabs and hand tighten
until snug with screwdrivers.
C
Tab
D
Fixture Hood
E
Socket
E
STEP 3 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 3

2of3
2018 QuoizelInc. ReleasedDate:2018-09-18
visit us on-line at www.quoizel.com
STEP 4 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (D) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (D) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (D) is secure, remove the mounting ball
and Fixture Body (D).
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
D
Mounting Screw
or Alternate Short
Mounting Screw
STEP 5 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 6 - Install the Fixture Body
A. Position the backplate and Fixture Body (D) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternative short mounting screws. Secure the Fixture
Body by using the mounting balls and hand tighten the mounting
balls until snug.
Figure 5
Figure 6
STEP 7 Install Bulbs and-Apply Silicone Sealer
A. Insert bulbs onto sockets and screw snugly into place.
B. Make sure the exterior wall surface and fixture backplate are free
of dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down both sides. Do not caulk the bottom of
the fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Exterior
Grade Caulk
Backplate
Figure 7
Mounting Ball
A
Backplate
D
Mounting Screw
or Alternate Short
Mounting Screw
Bulb (not
included)
Socket
Figure 4

3of3
2018 QuoizelInc. ReleasedDate:2018-09-18
visit us on-line at www.quoizel.com
BDS8410AGV
FINISH: AGED VERDE
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"
Fixture can
only be
mounted in
the direction
indicated
12”
10.75”
9”
10”
4.5”
22.5”