1of2
For Styles SNNL8409K and SNNL8409PN
Pleasegoto forproductcleaningtips.Gotothe selection.
LED16W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicated.
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
STEP 2 Fit Backplate to Crossbar Assembly-
A.
on Fixture Body (B) to the
Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate
should be snug against the wall and the mounting balls. If
on Fixture Body (B)
not, adjust
Figure 2
Mounting
Screw
B
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
B
Mounting Ball
A
Backplate
Exterior
Grade
Caulk
Backplate
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Figure 4
STEP 4 Install Fixture Body-
A. Position the backplate and
Fixture Body (B) onto the
Crossbar Assembly (A).
Place the holes in the
backplate over the mounting
screws. Secure the Fixture
Body by using the mounting
balls and hand tighten the
mounting balls until snug.
Figure 5
STEP 5 -Apply Silicone Sealer
A. Make sure exterior wall surface and
fixture backplate are free of dirt
before applying caulk. Using
exterior grade caulk, caulk over top
of backplate and down other side.
Do not caulk bottom of fixture
backplate to ensure proper moisture
drainage.
Your fixture is now assembled and
ready to use. Enjoy!
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (D) to make all wire connections.
Twist connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
2018 QuoizelInc. ReleasedDate:2019-08-09
visit us on-line at www.quoizel.com
Installation Guide #IS-SNNL8409
the length of the mounting
screw on the Crossbar
Assembly (A) by
unscrewing the
preassembled hex nut and
lock washer and then
screwing the mounting
screws in or out of the
crossbar until the correct
length is achieved. Once
the backplate on Fixture
Body (B) is secure, remove
the mounting ball and
Fixture Body (B) and
proceed to Step 3.
Package Contents
BFixture Body
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(C). Tighten until snug.
Supply Wires
with Ground Wire
Outlet
Box
Figure 1
A
Crossbar
Assembly
x1
A
Alternate
Mounting
Screw
x2
E
Outlet Box Screw
x2
C
Wire Connector
x3
D
C
