Radal Technology SPK-POD-A User manual

Phone: [phone]
Fax: [phone]
Email: [email protected]
Radal Technology Ltd
Unit 1 Webber Court
Billington Road
Burnley
Lancashire BB11 5UB
England
Issue Date: December 2006
Web: www.radaltechnology.com
Installation
SpeechPOD can be installed on walls or ceilings, but should
be installed in a location where the PIR Detector can ‘see’
persons entering the protected area.
The maximum distance that SpeechPOD will detect move-
ment is 5 metres (6 yards) with a 70 degree field of view.
Detection is immediate within this area and depending on
how you set up the SpeechPOD User Options your message
will be broadcast immediately.
SpeechPOD Voice Warning System (Part No SPK-POD-A
User Programmable Messages
SpeechPOD can be programmed with up to 7 user messages in any language. These messages are recorded and
programmed as detailed in the SpeechPOD Programming Data Sheet and are not covered in this guide.
User Option Menu
SpeechPOD is best programmed using the infra red remote control unit which opens up all the user options avail-
able.
Quick Start Guide
SpeechPOD is supplied with a number of standard, pre-programmed messages and settings, and can be put into
immediate operation. A summary of the default settings are shown below; any changes must be made prior to
fitting the battery or powering the system from an external power source. When you are happy with the configura-
tion:
• Insert a PP3 battery or connect a suitable external supply to terminals marked +ve and –ve. Note: do not fit
a battery if an external supply is being used).
• If the passive infrared is to be used to activate the product, plug the 3-way connector into the top right-
hand male header. The header is keyed to ensure correct polarity; do not attempt to force the connector
into the header incorrectly.
• For external activation, connect a normally open, voltage-free momentary contact to terminals marked
COM and TRIG IN. An external trigger can be used in place of, or in addition to the PIR detector. This input
can be programmed to operate normally closed going open by purchasing the Voice Programming Kit
(Part No PROG-KIT)
• SpeechPOD can be triggered externally from devices such as Magnetic door contacts, proximity switches,
pressure sensors (such as floor pads) or other alarm equipment using NO or NC clean contacts.
• Refit the front cover when completed and secure with the self tapping screw provided,
• Insert plastic protection cover to hide screw.

Phone: [phone]
Fax: [phone]
Email: [email protected]
Radal Technology Ltd
Unit 1 Webber Court
Billington Road
Burnley
Lancashire BB11 5UB
England
Issue Date: December 2006
Web: www.radaltechnology.com
Manual Configuration
For simpler installations, the use of the infra-red may
not be required.
SpeechPOD can be set up manually by selecting
the DIL switch settings shown across. Messages, vol-
ume and repeat functions are all programmable .
Of course, timer settings and other high end func-
tions cannot be selected manually.
1 = On (up) 0 = Off (down)
1
2
3
4
5
6
7
8
In fr are d R e m o te
Enabled 0
Disabled
1
Sound Output Type
Alert Tone 0
Speech
1
M essage Repeat Plays
100
(or Tone) 201
310
4
1
1
M essage Select
1000
2001
3010
4011
5100
6101
7
1
1
0
Battery M onitoring
9 V B atte ry 0
6 V B atte ry 1
S ettin g: 1 1 0 0 0 0 0 0
INTERNAL SWITCH SETTINGS
Factory Default Settings:
Manual
IR R emote Disabled, Speech O utput, 1 Message Play, Message 1, 9V Battery
In fra red R e m ote /P C O n ly
Autom atic Switch O ff Tim er: C ontinuous Operation
M essage Repeat D elay Tim er: Zero (Im m ediate O peration)
Product Specifications:
Voltage Internal: 9V PP3 Alkaline Battery
External: 6 – 12V DC
Current Standby Mode: 90uA @ 9V supply
Messaging Mode: 80mA @9V supply
PIR Range 0 < 5m with a 70 degree spread
Temperature -10 to +50 C
Humidity 0 – 95% non-condensing
Sound Output 89 dBa max. (Message dependant)
Weight 0.45Kg
Dimensions 150mm x 100mm x 50mm
Normally used for wet and slippery floor messages,
SpeechPOD can be set to play a message whilst the
floor is wet and then turn off after the timer has reached
zero. If set at zero SpeechPOD is ON
USER GUIDE NOTES
Normally used for setting a delay between message
plays. In mode 1 SpeechPOD will play the selected mes-
sage immediately on activation, but will then not play
again until the MODE 1 timer is zero
NOTE: You cannot use Modes 1 and 2 together
Normally used for setting a delay between message
plays. In mode 2 SpeechPOD will not play the selected
message immediately on activation, but will play it when
the MODE 2 timer is zero
NOTE: You cannot use Modes 1 and 2 together
To avoid message fatigue, the user can program all
seven messages on the same theme phrased differently.
With MODE 3 ON each message will be played in turn on
subsequent activations.
Used in conjunction with MODE 0. If you do not want
SpeechPOD to turn off after the time period selected in
MODE 0, then turning ON MODE 4 will ensure that after
MODE 0 time out SpeechPOD will not turn off, but will
default to play message 1.