Radio Shack 61-140 User manual

Please read this user’s guide before
installing, setting up and using your new product
www.radioshack.com
Thank you for purchasing your Two-Bell Wireless
Door Chime from RadioShack. You can use it as a
doorbell, remote pager and panic switch.
61-2117
Two-Bell Wireless
Door Chime
wireless door chime remote doorbell 1
remote mounting brackets (2) remote doorbell 2
lanyard (strap) user’s guide
M 3 screw* (4) M 2.6 brass
screw* (2)
M 3.5 screw* (5) anchor* (5)
* all screws shown at actual size
Mount your chime on a wall...
Drill a 1/4-inch hole and insert an anchor.
 Screw an M3.5 screw into the anchor,
leaving the head extended about 1/8-inch.
 Align the chime’s rear keyhole slot to the
screw head and slide the chime down.
OR set your chime on a flat surface using the
supplied stand
drill flathead screwdriver
C battery (3)* AAA battery (6)*
*Batteries not supplied
wireless door chime remote doorbell


1/4"
Install 3 C batteries in your wireless door
chime.
 Install 3 AAA batteries in each remote
doorbell.
Use only fresh batteries of the required size
and type.
Remove old or weak batteries that might leak
and damage electronic circuits.
Don’t mix old and new batteries or battery
chemistries.
NOTE
carry a doorbell with you as a panic alarm or
to let someone you frequently visit (such as an
elderly parent) know you have arrived coming...
OR mount your doorbell
Mark two holes using your doorbell holder.
Drill a 1/4-inch hole at each mark.
Insert an anchor in each hole.
 Align your doorbell holder with the anchors
and screw an M3.5 screw into each anchor.
 Slide your doorbell into the holder. To lock
the doorbell in place, insert an M2.6 screw
into the bottom of the doorbell holder.




1/4"
1/4"
61-140

©2004. RadioShack Corporation.
All rights reserved. RadioShack and
RadioShack.com are trademarks
used by RadioShack Corporation.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and
receiver.
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Consult your local RadioShack store or an experienced
radio/TV technician for help. If you cannot eliminate the
interference, the FCC requires that you stop using your door
chime. Changes or modifications not expressly approved
by RadioShack may cause interference and void the user’s
authority to operate the equipment.
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for one
(1) year from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers.
For complete warranty details and exclusions, check with your local RadioShack store.
RadioShack Customer Relations
200 Taylor Street, 6th Floor, Fort Worth, TX 76102
04/04
61-2117
AO0185ABA1
06A04
Printed in China
Frequency 433.92 MHz ± 600KHz
Doorbell current consumption <10mA
Chime current consumption <2mA @ standby
< 130mA @ sound playing
Chime battery low 2.4V ± 0.1V
Chime audio power > 80dBA @ 25cm
Doorbell operating temperature –20oC to 60oC
(–4oF to 140oF)
Specifications are typical; individual units might vary.
Specifications are subject to change without notice.
Slide your
chime to ON.
 Press one of your
two doorbells. Your
chime will “ding
dong” for doorbell
1and play “Home
Sweet Home” for
doorbell 2.


You can expand your doorbells to sound an
additional alarm. To do this, you will need to
wire one or both doorbells to an alarm that
contains a normally open contact.
Connect both tips of a 2-conductor wire (not
supplied) to a doorbell, as shown, using two
M3 screws.
 Connect both tips of the other end of the
2-conductor wire to the extra alarm.
Now, when you press your doorbell, both the
chime and the alarm will sound.
Slide your chime
to OFF when you
don’t want to
hear it ring.
TIP
In the event you need to change or reset the
channel or your chime and doorbell, use the
following instructions.
Select the same channel (1, 2, or 3) in the
wireless door chime and remote doorbell 1.
Repeat step 1 for remote doorbell 2.
TIP
If your door chime
rings when no one
presses one of the
remotes, you may be
receiving interference.
Switch the affected
chime and remote to
another channel.


61-140