Radionics D208RF User manual

Q
Radionics”
About This Document
To install the Expander:
1. Test the Expander at the desired location to
evaluate performance in the particular
envi-
ronment.
This document describes how to install, program,
2. Remove the Expander cover by pressing
wire, and test the D208RF and D216RF Point
down on the top center of the cover (see Fig
Expanders. ure 2).
Introduction
The RF Point Expander allows you to use up to 8
(D208RF) or 16 (D216RF) ITI
Learn Mode wire-
less devices with the Radionics D2212 panel.
Installation Guidelines
Observe the following guidelines when installing
the Expander:
l Leave 10” above the Expander for the
antennas.
l Avoid areas that are likely to expose the
Expander to moisture.
l Avoid areas with excessive metal or electri-
cal wiring, including furnace and utility
rooms.
or-- If unavoidable, mount on metal with the
antenna extending above the metallic sur-
face (see Figure 1).
m9
METAL
Y
Figure 1. Mounting on Metal Surfacer
D208RF and D216RF Point
Expansion Modules
Installation Instructions
Document Number: 466-l 020 Rev.A
October 1995
Installing the Expander
CAUTION: You must be free of static elec-
IB
tricity before handling circuit
boards. Touch a bare metal sur-
face or wear a
grounding stmp
to discharge yourself.
3.
4.
5.
Figure 2. Removing the Expander’s Cover
Press down on the lower-right comer of the
bass until the latch releases the circuit board
(see Figure 3). Gently lift the circuit board by
the terminal block to remove it from the base.
Place the circuit board in the cover while you
mount the base.
Hold the base against the mounting surface
and mark the three mounting holes (see Fig-
ure 4). Remember to leave at least 10”
above the base for the antenna.
Remove the base and install the provided
anchors, lf studs are not present.
Page 1
0 1995 Radionics
74-07476-000-A
RF Expander Installation Instructions

6.
Place the base on the
the provided screws.
wall and secure it using
CAUTION: When installing the Expander, only
use screws that match the specifi-
cations of the provided screws
(Type AB, #6 x 1” tapping screws).
TOP LATCHES
flgure 3. Removing the Circuit Board
J
Figure 4. Mounting with Circuit Board Removed
Connecting the Antennas to the
Expander
To connect antennas to the Expander:
1. Loosen the inside terminals of the left and right
antenna terminal blocks.
2. Insert an antenna into each inside terminal.
3. Tighten the terminal screws (see Figure 5).
Figure 5. Connecting Expander Antennas
RF Expander Installation Instructions
Page 2
(0 1995 Radionics

Programming
CAUTION: You must be free of Static electricity
before handling circuit boards.
Touch a bare metal surface or wear
a grounding strap to discharge
yourself.
To program the Panel for the Expander:
1.
2.
Select an address (7 or 8) by setting the address
jumper to 7 or 8 (see Figure 8).
Follow the programming procedure described in
the Radionics documentation for adding an RF
Point Expander to the D2212 panel. Make sure
you make the correct selection at the Address 7
or Address 8 prompt in the address configuration
group (see the D2212 Progamming Entry
Guide).
Figure 8. Setting the Address
Learning Points
See the D2212Keypad Diagnostics Manual for
instructions on learning points.
Wiring Connections
To wire the Expander:
1. Make sure the panel is powered down.
2. Connect panel terminals 10, 9, and 8to
Expander terminals -, +, and D, respectively (see
Figure 7).
Figure 7.
Connecting the Expander to the D2212
Testing
After wiring the Expander to the panel, you can
determine the Expander’s status by observing the
LED.
To determine the Expander’s status:
1. Check the panel and Expander connections.
2. Power up the panel.
3. The Expander’s LED shows the system’s status
(see Table 1).
Table 1. RF PointExpander’s Status LED
LED
Turns on
steady
Remains off
Indicates
Expander is functioning nor-
mally.
Expander is not properly
wired.
Blinks continu- Expander failed the power-
ously up test.
Blinks off Expander acknowledged
momentarily receiving an RF message.
Central Station Reports
The D2212 panel sends Modem II receiver reports
for
D208/D216 receiver tamper and receiver trouble
conditions.
RF Expander Installation Instructions Page 3 0 1995 Radionics

RF Point Expander Specifications
Compatibility:
Radionics D2212 panel
External Power:
7.5 - 14.0 VDC Class II Transformer
Current Dmw:
50
mA maximum
Operating Temperature Flange:
10” to 120°F
Dlmenslons:
4-1/16” x 5-1/4” x 1” (Lx W x H)
FCC Notice
This device complies with FCC Rules Part 15. Oper-
* ation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference that
may be received, including interference that may
cause undesired operation.
Changes or modifications not expressly approved by
lnteractlve Technologies, Inc. can void the user’s
authority to operate the equipment.
UL985 Household Fire (pending)
UL1023 Household Burglary (pending)
Interactive Technologies Inc.
2266 SECOND STREET NORTH
NORTH SAINT PAUL, MN
55109
T: 112/777-2690
F: 6 I2n79-4em
WIRELESS
Security
Automation
Access Control
ITI is a registered trademark of Interactive Technologies, Inc.
1995 Radionics, Inc., Salinas, CA, U.S.A. All rights reserved.
The Radionics logo is a registered trademark of Radionics, Inc., Salinas, CA, U.S.A.
Radionics
Radionics Inc., 1800 Abbott Street Salinas,
CA, 93901, U.S.A.
Customer Service: [phone]