Radionics D9412 User manual

33267C 3/97 © 1997 Radionics, Inc.
D9412/D7412 User’s Guide Supplement
Page 1
D9412/D7412 Control/Communicator
User’s Guide Supplement
Introduction
ThisreferencesupplementstheSecuritySystemOwner’sManual(71-06633-000)withthe
added command list features for the D9412/D7412. These flow charts will step you through
the operation of the new features. Please refer to the Owner’s Manual for the operation of
your new security system and its other basic command list features.
Add/ChangeUser ...................................................................... 2
UserPasscode..................................................................... 3
AddCard .............................................................................. 3
UserLevel ............................................................................ 3
Sub-UserID.......................................................................... 3
DeleteUserFunction................................................................. 4
AccessLevelControl ................................................................ 5
DoorControlFunction .............................................................. 6
CycleDoorSub-Function ...................................................... 7
UnlockDoorSub-Function .................................................... 8
SecureDoorSub-Function................................................... 9

D9412/D7412 User’s Guide Supplement
Page 2
33267C 3/97 © 1997 Radionics, Inc.
ADD USER ?
ENTER
ADD/CHANGE USER FUNCTION
ADD PASSCODE ?
ADD CARD ?
ADD LEVEL ?
NE XT
PREV
PREV
ESC
ESC
ESC
IDLE TEXT
Press the MENU key to enter the
Function Menu (or press CMD 46
to go directly to ENTER USER #)
then press
NE XT until
ENTER USER #
Key in user number
USER NUM: ###
NE XT
PREV
ENTER
ENTER
User Text
NE XT
PREV
PREV NE XT
CHANGE PASSCODE ?
If User Number exist
s
CHANGE CARD ?
If User Number exists
CHANGE LEVEL ?
If User Number exist
s
SUB USER ID ?
PREV NE XT
ESC
Use this function to add a passcode/card to
your system without assistance from your
security company. You need to know which
user numbers are available, the authority
level you want to assign to the new user, and
the areas in which it will be valid before you
add it. The D9412 has available up to 249
Users; the D7412 has available 99 Users.

33267C 3/97 © 1997 Radionics, Inc.
D9412/D7412 User’s Guide Supplement
Page 3
ENTER NEW CODE
ENTER
ENTER AGAIN
Key in passcode
NEW CODE * * * * *
*
ENTER
ADD PASSCODE ?
ENTER
NEW CODE * * * * *
*
ENTER
PASSCODE ADDED
CHANGE PASSCODE?
ENTER
PASSCODE CHANGED
If User Number ExistsIf New User Number
PRESENT CARD
ADD CARD ?
ENTER
CARD ADDED
CHANGE CARD ?
ENTER
CARD CHANGED
If Card Exists
If New Card
USER PASSCODE ADD CARD
VALID AREA #?
ENTER
When all area
assignments
have been made
USER LEVEL
AREA # # ?
ENTER
CHANGE LEVEL ?
ENTER
LEVEL ADDED LEVEL CHANGED
If User Number Exists
If New User Number
SUB USER #?
PRESENT CARD
SUB USER ID?
ENTER
CARD ADDED CARD CHANGED
If Sub User Number Exists
ENTER
Key in 1, 2, or 3
SUB-USER ID
PRESENT CARD
Card Presented at Reader
Card Presented at Reader
NOTE: At the end of each function the user may press theESC key to return to the
ENTER USER # prompt. To return to idle text, you must press theESC key again.

D9412/D7412 User’s Guide Supplement
Page 4
33267C 3/97 © 1997 Radionics, Inc.
ENTER USER #
ENTER
USER NUM: ###
DELETE USER ### ?
ENTER
USER DELETED
DELETE USER FUNCTION
ESC
Note: display will show
NOT IN USE
if user number is not in
the system
IDLE TEXT
then press
NEXT until DELETE USER ?
ENTER
User Text
ENTER
ESC
ESC
ESC
ESC
2 second timeout
NOTE :
Pressing ESC while within the DELETE USER
function, returns the user to the ENTER USER #
display prompt.
Pressing ESC while at the ENTER USER #
display prompt, returns the user to the DELETE USER
prompt in the function menu.
PREV
NEXT
PREV
NEXT
NOTE
Pressing PREV shows the previous User
Number or User Name in the user list.
Pressing NEXT shows the next User
Number or User Name in the user list.
Press the MENU key to enter the
Function Menu (or press CMD 53
to go directly to ENTER USER #)
When using this function to delete users out
of the system, more information is now
provided during the process to make sure
you are deleting the correct user.

33267C 3/97 © 1997 Radionics, Inc.
D9412/D7412 User’s Guide Supplement
Page 5
ENTER LEVEL:
ACCESS LEVEL CONTROL
IDLE TEXT
then press
NEXT until ACCESS LEVEL CTL
ENTER
Press the MENU key to
enter the Function Menu
Enter Access Authority Level #
ENTER
LEVEL # ENABLE? LEVEL # DISABLE?
If Access Level is
currently disabled:
If Access Level is
currently enabled:
Pressing ENT will enable the
level chosen and return you
to the ENTER LEVEL: prompt
Pressing ENT will disable the
level chosen and return you
to the ENTER LEVEL: prompt
NOTE: Pressing the ESC key twice will exit you out of this function.
After 20 seconds of inactivity, the system returns to idle text.
Use this function to manually enable/disable
access authority levels assigned to users. This
function can be used to temporarily disable a
user's access level instead of deleting and
adding the user.

D9412/D7412 User’s Guide Supplement
Page 6
33267C 3/97 © 1997 Radionics, Inc.
DOOR CONTROL ?
ENTER
DOOR CONTROL FUNCTION
CYCLE DOOR ? ENTER
UNLOCK DOOR ? ENTER
SECURE DOOR ? ENTER
NEXT
PREV
NEXT
PREV
NEXT
PREV
ESC
ESC
ESC
CYCLE 1 2 3 4 5 6 7 8
UNLOCK 1 2 3 4 5 6 7 8
SECURE 1 2 3 4 5 6 7 8
ESC
ESC
ESC
CYCLE DOOR?
(See Note 2)
NOTE 2:
# = Door is normal (available)
- = Door is not active, not in scope,
or user does not have access
level authority
C = Door is on timed door sequence
U = Strike and shunt are latched active
(held open)
X = Strike and shunt are deactivated
(secured)
IDLE TEXT
then press
NEXT until
NOTE:
Pressing ESC while within any one of the sub-functions
(CYCLE DOOR, UNLOCK DOOR,
SECURE DOOR), returns the user to the top
level display prompt for that sub-funtion.
Pressing ESC while at the top level display
prompt of any sub-funtion (CYCLE DOOR, UNLOCK
DOOR, SECURE DOOR), returns the user to the
DOOR CONTROL ? prompt in the function menu.
Press the MENU key to enter the
Function Menu (or press CMD 46
to go directly to CYCLE DOOR?)
To access the Door Control function, press
CO MMAN D 46 or press the MENU key and the
NEXT key until DOOR CONTROL? appears,
then press the ENT key. Three functions are
nested inside the Door Control function: Cycle
Door, Unlock Door, and Secure Door. The
flowchart shown below describes the process of
how to navi
g
ate throu
g
h this function.
(See Note 2)
(See Note 2)

33267C 3/97 © 1997 Radionics, Inc.
D9412/D7412 User’s Guide Supplement
Page 7
CYCLE DOOR ? IDLE TEXT
CYCLE 1 2 3 4 5 6 7 C
Is door ready to
cycle (i.e., not
secured or
unlocked)?
No
NOTE: Display shows
the status of each
door. (Door 8 is
currently activated to
allow access.)
Yes
NOTE: Display replaces door number with
"C" while door is open. Door number returns
when door is closed and strike is deactivated.
20 secon
d
timeout
Enter door #
to cycle
NEXT -- UNLOCK DOOR ?
PREV -- SECURE DOOR ?
Display remains until
another key is presse
d
ENTER
ES C
CYCLE DOOR SUB-FUNCTION
NOTE: PressingESC at any point,
returns the user to the UNLOCK DOOR
display prompt.
Users may use this function to momentarily unlock the access door to allow a person
an area. The amount of time the door stays unlocked is programmed by your securit
y
company.

D9412/D7412 User’s Guide Supplement
Page 8
33267C 3/97 © 1997 Radionics, Inc.
UNLOCK DOOR ? IDLE TEXT
UNLOCK 1 2 3 4 5 6 7 8
Is door
secured or
not available
to unlock?
Yes
No
(unlock door
)
NOTE: Display replaces
"U" with door number.
20 secon
d
timeout
Enter door to
unlock
Is door
unlocked?
No
Yes
(relock door
)
NOTE: Display replaces
door number with "U".
NEXT -- SECURE DOOR ?
PREV -- CYCLE DOOR ?
ENTER
ESC
UNLOCK DOOR SUB-FUNCTION
Users may use this function to keep the door unlocked to allow free access. Thi
s
function is used to lock the door back to normal operati
o
ESC

33267C 3/97 © 1997 Radionics, Inc.
D9412/D7412 User’s Guide Supplement
Page 9
SECURE DOOR ? IDLE TEXT
SECURE 1 2 3 4 5 6 7 8
No
(secure door)
NOTE: Display replaces
X" with door number.
Enter door to
secure
20 second
timeout
Is door
already
secured?
Yes
(return door
to normal)
NOTE: Display replaces
door number with "X".
NEXT -- CYCLE DOOR ?
PREV -- UNLOCK DOOR ?
Is door
available? No
Yes
ENTER
ESC
SECURE DOOR SUB-FUNCTION
The Secure Door function can be used to prohibit
access to users regardless of their access authority level.
ESC

 The Radionics logo is a registered trademark of Radionics
© 1997 Radionics, Inc., Salinas, CA, USA. All rights reserved.
Radionics, Inc., PO Box 80012, Salinas, California 93901-0012