Raisecom ISCOM HT803G-V (T) User manual

ISCOM HT803G-V (T)
UserManual
www.raisecom.com

2
1 Safety statements
1.1 Basic requirements
Read this document carefully before installing and using the ISCOM
HT803G-V. Otherwise, severe bodily injury or device damage may be
caused. Raisecom Technology Co., Ltd. (hereinafter referred to as Raisecom)
will not be liable for any losses caused by violation of any safety issues.
The ISCOM HT803G-V is an integrated device with precision components.
To prevent device damage caused by severe shock, avoid collision and
vibration. You shall not disassemble or repair the ISCOM HT803G-V by
yourself. If necessary, follow Raisecom engineers' instructions.
1.2 Environmental requirements
Place the device in an environment with good ventilation and no direct
exposure to strong light.
Keep the device clean and away from dust, water, and moist areas.
Do not place any object on the device to avoid damage due to overheating or
compressional deformation.
When installing the device, keep it away from heat or fire sources, such as
the electric heater and candle.
When installing the device, keep it away from electric appliances with
strong magnetic field or electric fields, such as the microwave oven and
refrigerator.
1.3 Electric safety
Use the original power adapter included in the package or replacement
provided by Raisecom. Using other power adapters may cause device
damage or other problems.
The voltage and current of the power supply must meet requirements on
input voltage and current. Overcurrent protection is required.
Keep the power plug clean and dry to avoid electric shock or other risks.

3
Before pulling out a cable from the device, stop using the device and power
it off.
If you do not use the device for a long time, power it off and pull out the
power plug.
Do not let water or other liquid flow into it. If this happens, power off the
device immediately, pull out all cables from the device, and contact
Raisecom technical support personnel.
1.4 Laser safety
Personnel operating the fiber must be trained on laser safety.
Do not bend the fiber much to make its diameter smaller than 7.5 cm or 3
inches. Otherwise, the fiber may be damaged or optical signals may be
blocked.
Do not stare into the optical interface or end face of the fiber to avoid eye
injury.
1.5 Other precautions
If any abnormality occurs, such as smoking, abnormal sound, and peculiar
smell, stop using the device immediately, power it off, pull out all cables
from it, and contact Raisecom technical support personnel.
Do not let any object (such as metal) enter the device through heat
dissipation holes.
Do not scrape or abrase the device shell. Otherwise, falling coating may
cause device malfunction (even short circuit if entering the device) or
human allergy.
Do not let children play with the device or components to avoid dangers
caused by swallowing, and so on.

4
2 Legal notice
The copyright of this document is owned by Raisecom. No part of this publication
may be excerpted, reproduced, translated or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without written
consent from Raisecom Technology Co., Ltd.
When a user finishes installing the device and starts using it, it implies that
the user has completely understood safety statements of this device. The
user is liable for any losses or damage caused by violation of safety
statements.
The information in this document is subject to change without notice. Every
effort has been made in the preparation of this document to ensure accuracy
of the contents, but all statements, information, and recommendations in this
document do not constitute the warranty of any kind, express or implied.
Raisecom is not liable for any losses or damage caused by natural disasters
beyond Raisecom's responsibilities, such as earthquake and flood.
3 Device specifications
3.1 Technical specifications
Table 3-1 lists technical specifications of the ISCOM HT803G-V.
Table 3-1 Technical specifications of the ISCOM HT803G-V
Parameter
Description
Dimensions
140 mm (Length) × 105 mm (Width) × 33
mm (Height)
Weight
< 1 kg
Maximum power consumption
< 5 W
Input of the power adapter
100–240 VAC (50/60 Hz)
Output of the power adapter
12 VDC, 1 A
Operating temperature
0–50°C
Operating humidity (RH)
10%–93% (non-condensing)

5
Table 3-2 lists technical specifications of the PON interface on the ISCOM
HT803G-V.
Table 3-2 Technical specifications of the PON interface
Parameter
Description
Interface type
SC/APC
Tx optical power
0–4 dBm
Rx sensitivity
-28 dBm
Minimum overload
-8 dBm
Laser safety class
Class 1
3.2 Packing list
Table 3-3 lists packing list of the ISCOM HT803G-V.
Table 3-3 Packing list
Device/Component
Quantity
ISCOM HT803G-V
1
Power adapter
1
Ethernet cable
1
User manual
1
If any item mentioned above is missing, contact the SP.

6
4 LEDs

7
5 Connection and usage
5.1 Interfaces and buttons
The figure shown above is diagrammatic only. The actual
appearance is subject to the device provided by the SP.

8
Warranty Record
Date
Record of Damage and
Repair
Signature
of Repair
man
Signature of
Customer
Damage
Reason
Repair
Measure
Address: East-11, Raisecom Building, 10 Xi Bei Wang East Road, Haidian District, Beijing, China
Post Code: 100094
Tel: [phone]
www.raisecom.com
-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - ----------------------------------------------------------------------

9
Product Warranty Sheet
Customer Name:_ _ _ _ _ _ _ _ _ _ _ Phone Number:_ _ _ _ _ _ _ _ _ _ _ _ _ _
Address:_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Thank you very much for purchasing Raisecom products. For the sake of being
responsible for you, and guaranteeing premium after-sale service, please carefully
read and fill up this sheet.
Warranty Policy:
1. Our products carry a type warranty period of 1 year after warranty sheet has
been provided to you. In this period, any problem that caused by the product
itself and confirmed by our technical engineers will be fixed free of charge.
2. Please present the warranty sheet and the receipt when requesting services.
3. The following circumstances are not included in the warranty:
Products are misused, or used in abnormal situations.
Damages that are attributable to improper installation, disassembly or
repairing by unauthorized parties.
Product serial number and the number on receipt are amended without
permission.
Damages caused by natural disasters or human behaviors.
Product has been exceeded warranty period.
Damages that are attributable to use the components that are not Raisecom's.
Damages caused by accident or man factor, include: Computer Viruses,
Improper Carry, Extrusion, Kotow, Scuffing, Bump, High-temperature,
Inputting improper voltage, Cauterization, etc.
Damages caused by irresistible power (for instance: Earthquake, Flood and
etc). Other damages which are not attributable to product design, technology,
product, and quality.
4. We are providing lifetime repairing services to our products. Repairing
outside the warranty period will be charged of the cost.
-- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -------------------------------------------------------- -------------

10
5.2 Installation modes
The ISCOM HT803G-V can be installed on a stable workbench or a wall.
Installing the ISCOM HT803G-V on the workbench is informal
because unpredictable events (such as collision or object falling)
may prevent the ISCOM HT803G-V from working properly or
even damage it. We recommend installing it on a wall.
Install the ISCOM HT803G-V on a wall as below:
Step 1 Choose a proper height of installation position so that you can easily
observe LEDs and connect the power supply.
Step 2 Knock two cement nails, with spacing of 110 mm (distance between two
wall-mount holes), into the wall. The diameter of a cement nail should
be smaller than that of the wall-mount hole (8 mm).
Step 3 Align wall-mount holes with knocked cement nails, and hang the device
on nails. The device is hung by the nails on the wall.
Figure 5-1 Wall-mount installation
Step 4 Check by slightly shaking the device whether it is firmly installed on the
wall.