Ram Mounts RAM-B-166 User manual

Phone case that contain metal, magnets,
or are thicker than 3mm will interfere with
wireless charging.
This charger is designed for Qi-compatible
devices. If your phone does not have built-in
wireless charging capabilities, please use a
certified Qi wireless charging case or receiver.
Refer to your phone’s user manual for detailed
features and functions.
1.We suggest to use QC2.0 or QC3.0 adapter
for fast charging.
2.Do not place metal objects, magnets,
magnetic stripe cards, and hard drive based
devices near the wireless charger. It may
cause data corruption.
3.Do not attempt to modify, disassemble, or
repair this product.
4.Do not expose to water, moisture,
or extreme temperatures
( below 40℉ or above 90℉)
Wireless Charging
Position your phone in the center of the
designated charging area. You phone will
indicate when charging begins.
MANUAL
Ram Mounts
Quick Grip Charger
Model # - RAM-B-166
1. Can be customize
2. Diameter=50mm,can be customized
3. Input Power:10W 5V-2A; 9V-1.67A
4. Output: 5W / 7.5W / 10W
5. Conversion Efficiency: 85% Max
6. Transmitting Distance: 5-8mm
7. Working Frequency: 115-205KHz
8. Product Standard: WPC v.1.2.4
9. Protective measures: FOD,DPL,SCP,Over temperature,over
voltage protection, software/hardware dual over current protection
enhanced VRVS;Dedicated high power low loss MOS & MOS driver
10. Compatible for:QC2.0/QC3.0

FCC warning
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception,
which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.
To maintain compliance with FCC’s RF Exposure guidelines, This
equipment should be installed and operated with minimum distance
between 20cm the radiator your body: Use only the supplied
antenna.

IC Caution:
Radio Standards Specification RSS-Gen, issue 5
- English:
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
This device may not cause interference.
This device must accept any interference, including
interference that may cause undesired operation of the
device.
RF exposure statement:
The equipment complies with IC Radiation exposure limit
set forth for uncontrolled environment. This equipment
should be installed and operated with minimum distance
20cm between the radiator and your body.
- French:
Cet appareil contient des émetteurs / récepteurs
exemptés de licence conformes aux RSS (RSS)
d'Innovation, Sciences et Développement économique
Canada. Le fonctionnement est soumis aux deux
conditions suivantes:
Cet appareil ne doit pas causer d'interférences.
Cet appareil doit accepter toutes les interférences, y
compris celles susceptibles de provoquer un
fonctionnement indésirable de l'appareil.
Déclaration d'exposition RF:
L'équipement est conforme à la limite d'exposition aux
radiations de la IC établie pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec
une distance minimale de 20 cm entre le radiateur et votre
corps.