RATTAN COMPASS User manual

www.rattanebike.com
COMPASS
USER MANUAL

We really appreciate your business cooperation
with us and we wish you a good time with the
ebike.
Please feel free to contact us if there is any
questions about the bike.
Contact details
Email: [email protected]
Website: rattanebike.com
Phone: [phone]
Thanks for your Compass Ebike
purchase

Contents

2
Rattan Ebike LLC assumes no liability for any
harm, injury, or death of the rider.
This manual is not intended to be used as a detailed service
manual. Please feel free to contact us if there is any thing you
would like to know.Rattan Ebike recommends a
comprehensive security check before the bike begins his
first travel.
For technical assistance or warranty claims contact Rattan Ebike
at
Phone：[phone]
E-mail：[email protected]
Congratulations on your purchase of a new Rattan Ebike! The
bike comes 85% assembled and here is the guide helps you get
familiar with your new bike in unboxing. The bike may need
adjustments in this process as shipping can sometimes be
bumpy. We recommend an adjustment and inspection by a
reputable, certified bicycle mechanic before the first riding.
Please read the whole manual patiently before you use the
new electric bike
·do not modify or disassemble the original electrical
components of the bike.
Any of the above will invalidate the warranty and even bring
hurt to you.There will be some risks during the process of
experiencing the bike.

3
1. Loosen the hub screws to make enough space for the
fork.
2. The two feet of the front fork must be aligned with the
hub screws position before the fork can be installed.
3. Tighten the screws
Key
MAINPARTS INTRODUCTION
Power adapter
Charger cable
Compass Ebike
Tool
User manual
ASSEMBLY INSTRTUCTIONS
Front fork:

4
1.Tighten the screws on the stem
2.Loosen the screws on the handlebar,
3.Hold the handlebar in the middle of the joint,
tighten the screws.
1.Unscrew the screw for headlight
2.Place the headlight at a right position, then tighten
the screw.
Headlight:
Handlebar:

5
1.“L” indicates the left side, “R”indicates the right side.
2.Make sure tighten the screws connect the pedals and
cranks.
3. Twist to left when install the left side and twist to right
when install the right one.
Battery:
Pedal:
1. place the battery on the bike
2. Turn the key to lock/unlock the battery on bike
according to the position attached to the battery as the
picture shown.
Charge the Ebike without removing the battery
Or Remove the battery, and charge it.

6
1.Search a comfortable height of saddle by sitting on
the saddle with your feet on the ground.
2.The height of the Saddle should not be pulled
higher than the safety tick marks on the Saddle Post.
3.Then please lock the seat post clamp tightly.
Brake:
Seat post:
ADJUSTMENT
1.Make sure the brake disc is in the middle of two
brake pads.
2.Adjust the brake tension according to your riding
habits. Loosen the screw and adjust the brake wire to
the suitable brake tightness. Loosen the screws to
adjust the brake disc(abnormal noise or brake stuck
when braking). Adjust the brake pad to keep the rotor

7
1.Adjust the screw on the shifting wire when it is hard
to switch the shifter.
2.Loose screw 1 slightly when the shifter can`t switch
to the 7th gear; on the contrary, if it can`t gear down
to the 1st level, loose screw 2 slightly and try again.
Loosen screw 1 and 2 to make the derailleur move
slightly away from the rim in case of the chain rubs
the tire.
4.Tighten the screw when the shifter can`t switch to
the highest gear.
Derailleur:

8
There is a serial number attached on head-tube or on
the bottom axis connecting the pedals as shown in the
following picture. Please take a picture ahead once you
received the bike. You may be asked for a picture of
your bike ’ s serial number as a part of warranty
requests and may also be asked to provide this
number to law enforcement provided that your bike is
stolen.
Serial number:
PREPARING TO RIDE

9
check:
Make sure all components are tightened. Adjust
the height of the handlebar and the seat post. DO
NOT raise it above the safety line.
Make sure the brakes can cut off the power supply
to the motor, and whether it is sensitive and reliable.
Make sure the front and rear axle nuts are
tightened.
Make sure the display, brakes and lights can work
properly.
Make sure the chain is tight.
Make sure the pedals and all the connection parts
are firm and would not loose, and whether the crank
is flexible without jamming.
Make sure the front and rear tire pressure and tire
wear are suitable for your journey ahead.
Make sure the throttle works well without
jamming, and whether it feels tight or loose when
pressing the throttle.
Make sure the battery has been locked.

10
This mode does not require any power. It allows the
E-bike to work as other regular bike. You will be
automatically switched to this mode when the
battery dies while riding.
Turn on the display and press the throttle slowly to
get started. When release the throttle slowly, the
riding speed will gradually drop until power off.
Accelerate slowly and use the pedal assist in the
beginning of riding. When riding against the wind or
climbing the hill,avoid using the pedal assist to
protect the battery.
RIDING GUIDANCE
Three modes:
Pedal Mode:
Electric Mode:
Pedal Assist Mode:
Display:

11
1. Material&Dimension
1) Material
Caser and Cover and Press button: ABS,
LCD window: PMMA
2) Outside and mounting dimensions(mm)
3) Press button outside and mounting dimensions(mm)
4)Installation
●Install the display in the middle of handlebar, then adjust
to suitable angle, install the press button to left side of
handlebar.

12
●Power off the device, connect the device to
controller.
●Power on
2. Overview of GD06
1) 5s protocol:
Equipped with independent press buttons
2) Speed：
Real-time SPEED
3) kmh/mile：
Kmh/MPH according to habit
4) Battery level：
Indicates the battery level in real time
5) Head light control：
Press button to power on/off
6) Back light adjustment：3-level adjustment

13
3. Presentation of screen
1) Battery level: 5 levels, voltage interval could be
customized
2) Speed：Real-time SPEED
3) Speed unit：Kmh/MPH
4) 6km mode
5) Assist level：actual assist level 0~5. 6) Head light
icon：indicates when head light and back light are on
7) Distance：Trip/ODO
8) Driving Duration
7) Assist level：
From 0 to 5, press button to change assist level, 0-no assist,
default value
8) Distance：
ODO/Trip/Driving duration
9) Error code：
Please refer to appendix table 1 for definition
10) 6km mode：
In this mode, it will display “WALK” on the screen
11)Parameter setting：
Set parameters, such as: wheel size, speed limit etc

14
4. Press button definition
GD06 uses independent press button, in total three buttons:
5.Operation instructions
1) Power ON/OFF
When the power is off, Long press （MODE ）during
3seconds, screen will display all contents and start to normal
working mode, and controller will be turned on When the
power is on, Long press （MODE）during 3 seconds,screen
will be powered off, and controller will be turned off. If no
any operation both on bike and display during
10minutes(time could be set), the display will turn off
automatically, in this case, no power consumption for both
display and controller.
2) ODO/TRIP
Long press (UP )and (MODE) switch different speed
information,Real time speed（SPEED）→ Max speed（MAX
SPEED）→Average speed（AVGSPEED）
3)ODO/TRIP/ Driving Time/Error Code
Short press(MODE) to switch ODO/TRIP/ Driving Time/Error
Code Trip(Single trip distance)→ODO(Accumulated distance)
→TM(Driving Time)→REE(Error Code).
UP MODE DOWN

15
4)Assist level
Short press (UP)or (DOWN) to change assist
level,default value is level 1
5) Head light control
Long press(UP) for 3 seconds turn on/off the head
light.
6) 6km mode
When the bike is stopped, long press(DOWN) , will
enter 6km/h mode, the speed will be 4.5~7.5km/h
according to different road conditions,
“WALK” will show up on screen, long press again or
short press ,will quit 6km/h mode. Long press or
short press could be customized by clients.
1.When the display is powered on,long press(UP)
and(DOWN) ,will enter parameter setting mode,in
this mode, can change parameter values, long
press again and will quit parameter setting mode
or no operation during 10s will also quit this
mode.
2.n parameter setting mode,short press(UP) /
(DOWN) will change parameter value,short
press(MODE) will save current value and switch
to next parameter.
1) P01-back light lightness：
short press(UP) / (DOWN)will switch from 1 to
3,Level 3 is lightest. Level 2 is default value.
6.Parameter setting

16
2) P02-kmh/MPH：
Short press(UP) /(DOWN) to Switch kmh/MPH.
3) P03-Working voltage：
short press (UP)/ (DOWN)to switch 48V.
4) P04-Auto shutdown time: short press(UP) /(DOWN) to
switch from 0 to 60, it is the time(in minutes) to shut down
the screen automatically if no operation 0 means never shut
down, Default value is 10 minutes
5) P05-Number of Assist levels：
Short press (UP)/(DOWN) to change level 3->5->9. 3：3
assist levels
5：5 assist levels
9：9 assist levels
06) P06-Wheel size selection：short press(UP) /(DOWN) to
switch wheel size,step：16 inch,20 inch,22 inch,24 inch,26
inch,700C,28 inch.
07) P07-Number of magnets for speed sensor：
short press(UP) / (DOWN)to switch from 1 to 15.
08) P08-speed limit：short press (UP)/ (DOWN)to set the
speed limit from 10 to 41km/h.
09)This feature is reserved: display P09, invalid.
10)This feature is reserved: display,invalid.

17
11) P11-assist sensitivity setting：short
press(UP) / (DOWN)to switch from 1 to 24.
12) P12-assist starting power setting:short press(UP) /(DOWN)
to switch from 0 to 3.
13) P13-Assist magnetic disc types short press (UP)/(DOWN)to
switch from
5->6->8->10->12 ,different numbers of
magnets.
14) P14-Current limit for the controller ：short press(UP) /
(DOWN)to switch from 1 to 20A
15) This feature is reserved:display P15,invaild.
16) P16-Reset ODO distance:long press(UP) during 5 seconds.
17) P17-The signal direction of the booster
sensor：short press (UP)/(DOWN) to switch
from 0 to 1; 0: Booster signal；1Power signal negative.
18) P18-Shift gears with gear ：short press(UP) /(DOWN) to
switch from 0 to 1; 0：Don't shift gears；1: Shift gears.
19) P19- Throttle the 6KM function：short press (UP)/ (DOWN)
to switch from 0 to 1; 0：Turn to the normal；1：Throttle 6Km.

18
7.Specifications
1) Power supply: 24V,36V,48V
2) Rated current: 10mA
3) Max current: 30mA
4) Leakage current after power off: <1uA
5) Current supply to controller:50mA
6) Working Temperature：-10~60ȭ
7) Storage temperature：-20~70℃
8. Error code definition
When an error appears, GD06 will notice users by different
codes,
please refer to table 1 for different codes: