Worksman PORTOTRIKE PT, PORTOTRIKE PT2F, PORTOTRIKE PTCB, PORTOTRIKE PT2CB, PORTOTRIKE... User manual

- 1 -
Worksman PortoTrike: The Compact Deluxe Adult Folding Tricycle
Assembly Instructions, Parts List, and Owner’s Manual for PT, PT2F, PTCB, PT2CB, PT3CB
Congratulations on your purchase of the Worksman PortoTrike Compact
Folding Tricycle, one of the most popular adult recreational tricycles of all
time. This is a recreational tricycle for the consumer market, with a
recommended weight limit of 210-225 pounds, depending on brakes
chosen. The low step-through and compact frame design are ideal for
those riders who simply want to ride leisurely, safely, and comfortably.
The PortoTrike has been carefully manufactured in the USA using
domestic and imported parts, with simple finishing assembly required. It is
always recommended to have a qualified bicycle mechanic perform
repairs and assembly of any cycle. Please read these instructions
thoroughly prior to assembling and riding.
Failure to have this cycle professionally assembled could result in injury or death.
Tools Needed for Assembly: Phillips and Flathead Screwdrivers, Large Adjustable Wrench
(A) Unfolding the PortoTrike:
·Remove protective bubble wrap and
cardboard.
·Located at the PortoTrike’s hinge, find the
quick-release arm, loosen it, and swing
towards the rear.
·Now that hinge is free, unfold the trike so that
the frame is straight.
·Slide quick-release arm’s pin down through
frame hole, pull lever forward, and tighten.
(B) Steps to Attach Front Wheel/Front Fork to Main Frame:
a. Slide one bearing (49B) onto the fork
steerer tube cone, balls facing up.
b. Slide fork assembly into the front of the
frame; make sure that bearing is flat.
c. Place the remaining bearing (49B), balls
facing downward, onto the steerer tube.
d. Thread top adjustment cone (52B) onto
this tube. Tighten the bottom. Again,
make sure both bearings are sitting
evenly inside their respective cones.
Hand-tighten until tube is tight enough
the sit steady but can still turn freely.
e. Place keyed silver washer (53) above the
adjustment cone. (Key inside slot in tube.)
f. Next, place quick release clamp (4911B—
it has a black handle) above washer, with
clamp arm towards the back of the cycle.
g. Next, place reflector bracket (5030F) on top
of the clamp with key inside slot as done
before. Make sure holes point upwards.
h. Place 2 regular washers (53B) above the reflector bracket, followed by the small black-keyed washer (53BWO),
and then screw on the threaded lock nut securely (54B).
Note: Headset assembly should be tight enough so all pieces are touching and there are no loose pieces.
(f) (g) (h)
(a)
(b)
(c)
(e)
(d)

- 2 -
(C) Handlebar Set Up:
·Open quick-release clamp (4911B) on headset assembly.
·Insert handlebar stem (55E) into the front tube, with the head of the stem facing forward. NOTE: Must be at least
4’’ into the tube, or damage to fork may occur.
·With stem at preferred height, tighten clamp and tighten screw securely.
·Insert the handlebars (55F) into the stem opening, and place at desired angle; then simply tighten the bolt until
handlebars remain in that position. Check the handlebar stiffness before riding.
·Install brake levers:
·Remove brake levers from inside front wheel, and remove packaging.
·Remove small bolts from each of the brake levers, and open clamps.
·Place brake levers as seen in picture, replace the bolts, and tighten.
·For 3 Speed Models, follow the same instructions in order to attach your gear shifter.
·Next slide handlebar grips (55B) onto handlebars.
·This can be done easily after soaking the handlebar grips in warm water for 30 seconds.
·
(D) Pedal Installation:
·Pedals are marked Lfor left, and Rfor right, on the
threaded end of the pedal axle.
·Using a wrench, screw in the R(right) pedal onto the
right side of the trike (the chain side), and similarly,
screw the L(left) pedal onto the opposite side.
·IMPORTANT: LEFT PEDAL TIGHTENS
COUNTERCLOCKWISE!
·Attempting to insert pedals on wrong sides will damage
the threads on the pedals. DAMAGE BY FAILURE TO
FOLLOW INSTRUCTIONS WILL NOT BE COVERED
BY WARRANTY.
(E) Rear Cargo Basket Installation:
·Place basket on the rear of the frame, centering the basket between the
rear two wheels.
·Place washers onto the basket’s bolts.
·Place both bolts through the outer hole in the basket, through the holes in
the frame, and then install the two elastic stop nuts under the frame into the bolts.
(You will need two wrenches to tighten these bolts fully. It will get more difficult to
turn the wrench as the bolt starts to grab the elastic in the nut.)
(F) Seat Installation:
·Place seat post into clamp located on bottom of seat. Place at desired angle and
tighten securely.
·Make sure that the seat post is all the way through the clamp.
·Place other end of seat post through the quick-release clamp (black handle) at
desired height and close clamp. Tighten bolt on clamp to ensure that the seat will
not move when user sits on the trike.
·When placing seat at desired height, make sure that the seat post is at
least 3.5 inches inside the seat post tube.
(G) Reflection Placement and Installation:
·There are a total of 5 reflectors:
·3 curved rectangular white reflectors for each wheel.
·1 square white reflector for front.
·1 square red reflector for rear.
·Rear Reflector:
·Screw through the mount located on the rear cargo basket using the small screw given.
L and R are written
on these surfaces

- 3 -
·Front Reflector:
·Screwed on the same way as the Rear reflector, but it attaches to the front reflector bracket that was
previously installed with the headset assembly. Make sure that the two locator-knobs fit into the holes
in the bracket.
·Wheel Reflectors:
·These reflectors install on the inside of the two layers of spokes. The reflector has a groove that will
be facing you that will be placed onto a spoke. When this is done, place the bolt given to you through
the whole, and tighten the nut on the opposite side—this should sandwich the spoke between the bolt
and the reflector, and secure the reflector in position.
Make certain to read the manual prior to riding. Make certain to understand the rules of the road and safety
instructions. Do not ride cycles after dark. In dusk or dawn, lights are recommended. Use of a helmet is always
a good precaution, and may be required by law. Inspect your cycle regularly for wear of parts and replace as
required. Only use factory original replacement parts. Lubricate chain, caliper brake pivot bolt and other parts
as necessary and at least once every 6 months.
How to Fold Your Worksman Folding Port-o-Trike Tricycle
To fold, pull the “Safety-Loc”lever to the loose position. Pivot the lever toward the side of the
tricycle. Lift up on the arm, releasing the pin from the “Safety-Loc”hinge pinhole. You will then
be able to fold the frame. Be careful to position the pedals for wheel clearance. (The front
wheel should tuck in toward the rear of the frame to the inside of the left wheel.) To refold, see
Section A of these instructions. It is advisable to place grease in the pinhole on the frame
hinge every so often so the “Safety-Loc “system works easily.
Owner’s Responsibility:
1) Make certain that all assembly instructions have been followed and that the tricycle is safe and ready to ride.
2) Perform maintenance as needed, and provide instructions to anyone who may ride the cycle.
3) Conform to all local regulations, including traffic laws, and be deemed physically fit to ride a cycle.
Where and How to Ride a Three Wheeler: It is recommended that you ride in areas that are paved and relatively flat.
Avoid steep hills and naturally ride where you feel safe. Low traffic areas are most desirable. Sit up straight when going
straight. When turning, you should lean ever so slightly into the direction of the turn. Slow down prior to making a turn.
Never make sharp turns. Steer by pointing the front wheel in the direction you wish to go. Note - Tricycles have a
tendency to pull slightly to the left. This is common in all three wheelers.
It is common to hear some clicking noise that emanates from the chain when the tricycle is new. This will stop when the
chain is broken in. (Chains stretch slightly when new.)
Brakes and 3 Speed Coaster Brake Information: Port-o-Trikes are equipped with a front caliper, drum brake, or both.
Operate the hand brake by squeezing the hand lever on the handlebar. Coaster brakes (foot brakes) are engaged by
pedaling backwards until the brake operates. It is best to gently slow the cycle down using the hand brakes and
completing the stop using the coaster brake. For those models with the 3 speed coaster brake, simply use the handlebar
mounted shifter to select the desired gear. Gear 1 is the easiest gear for easier starting or going up hills, while gear 2 and
3 are useful once you get to your desired riding speed. Select the gear that suits your individual taste and comfort level.
DO NOT SHIFT AND PEDAL AT THE SAME TIME. PAUSE PEDALLING, SHIFT, AND RESUME PEDALLING.
Axle Bearings: Be sure to lubricate rear axle and wheel bearings every six months. Use a bearing lubricant, which is
available at any hardware or auto parts store. Failure to lubricate axle bearings can cause the bearing to seize and cut
through the axle. If you hear a grinding or hissing sound, lubricate bearings immediately or replace if damaged!

- 4 -
Replacement Parts List: (PT, PT2F, PTCB, PT3CB)
Please note that there are two styles of PT rear axles and drive wheels. Style “A”uses a round drive plate welded to the axle with
three prongs that protrude into three holes in the hub of the drive wheel. Style “B”uses a keyway, which is a rectangular piece of steel
that slips between a groove in the axle and a slot in the drive wheel hub. See illustrations below to determine which style you have
before ordering any replacement parts.
Front End Assembly Crank Assembly and Parts
153 Front Fork (specify color) 7217 Pedals (pair)
50B-V Head Parts Set 1265 Crank Parts Set (All parts inside crank housing)
4911B Quick Release Clamp (fork) 3275 Crank (5.5”)
48B Ball Cup (Upper) for frame head tube 1380C Front Sprocket 36T
48C Ball Cup (Lower) for frame head tube 1267G Complete Crank set (1265, 3275, 1380C)
49B Bearings for Headset (pair)
51B Fork Bottom Cone (presses onto fork) Fenders (Plastic is standard as of 2012)
52B Threaded Top Adjusting Fork Cone 4800 Front Fender (Chrome)
53 Key Washer (Thin - Lower) 4809 Rear Fender (Chrome)
53B Key Washer (Thick - Upper) FS20 Rear Fender Kit Complete (Chrome)
53BWO Key Washer (Thin - w/o tab) 4800L Front Fender w/ Hardware (Chrome)
54B Top Fork Lock Nut Plastic
55B Hand Grips (pair) 4800C-BLK Front Fender w/ Hardware (Plastic)
55E Handlebar Stem 4800CR-BLK Rear Fender (Plastic)
55F Handlebar FS20P Rear Fender Kit Complete (Plastic)
5030F Reflector Bracket Fender Parts
4802 U-Brace: Front Fender
Frame Parts 95 L-Bracket: Front Fender
3200CB Frame (Specify color) 4811 Brace w/ Clamp: Rear Fender (Each)
4908K-S Safety-Loc hinge bolt / lever parts kit
Seat and Related Parts
4908D Seat post (1”x 15”w/ 7/8”top) 4911A Quick Release Clamp for Seat Post
6911V Saddle Wide (with springs - optional) 7910V Saddle- Wide (w/o springs - standard)
Front Wheel and Related Parts Rear Axle and Related Parts
M20F Front Wheel w/o Drum w/o Tire Note Style A & Style B replacement parts! (See diagrams.)
M20F-AL Front Wheel w/o Drum w/ Alloy Rim PARTS FOR EITHER STYLE A OR STYLE B
467A Front Drum Brake Wheel w/o Tire 57 Rear Axle Elastic Lock Nut
467 Front Drum Brake Wheel w/Tire 4129A Rear Freewheel Sprocket (PT, PT2F)
467A-AR Front Drum Wheel w/ Alloy Rim 62B Set screw for 62 or 69B
G250 Front Drum Brake (Hub only!) 62C Keyway for 62 or 69B
G219 Brake Cable and Casing: Drum Brake 174W Rear Axle spacer washer
G220 Brake Cable and Casing: Caliper Brake STYLE A AXLE PARTS (5/8”axle w/ 3-prong drive plate)
174HD Bearing for rear axle/wheels (cartridge style 5/8”)
Rear Free (Left Side) Wheels 176 Rear Axle w/ drive plate (round disk w/ 3 prongs)
468A Rear Wheel w/ 2 bearings w/o tire 62 Bushing (5/8”for 4129A)
468 Rear Wheel w/ 2 bearings w/ tire 69B Fixed Drive Sprocket (5/8”PTCB, PT3CB)
468A-AR Rear Wheel w/ 2 bearings w/ Alloy Rim STYLE B AXLE PARTS (3/4”axle center w/ keyed drive slot)
173 Bearing for rear axle (cartridge style 3/4”)
Tires, Tubes, Wheel Parts 174HD Bearing for rear wheels (cartridge style 5/8”)
6012W Tire 20x1.75 White Wall 176K Rear Axle w/ keyway slot
6012R Tire 20x1.75 Red Line 61 Bushing (3/4”for 4129A)
6012A Tube 20x1.75 69A Fixed Drive Sprocket (3/4”PTCB, PT3CB)
1017A Rim Strip
1014H Spoke for front drum wheel (Sold Qty 36) Rear Drive (Right-Side) Wheels
1014I Spokes for rear wheels (Sold Qty 36) 468DA Rear Drive Wheel w/o tire (Style A)
M20 Rim Only (not a built wheel) 468D Rear Drive Wheel w/ tire (Style A)
468DA-AR Rear Drive Wheel w/o tire w/ Alloy Rim (Style A)
F820L Non-Locking Brake Lever –Left (Std) 468KA Rear Drive Wheel w/o tire (Style B)
F820R Non-Locking Brake Lever –Right (Std) 468K Rear Drive Wheel w/ tire (Style B)
F852L Locking Brake Lever –Left (Optional) 468KA-AR Rear Drive Wheel w/o tire w/ Alloy Rim (Style B)
F852R Locking Brake Lever –Right (Optional)
WHEN ORDERING WHEELS WITH TIRES, BE
SURE TO SPECIFY WHICH TIRES YOU NEED. A B

- 5 -
Transmission and Related Parts
301 Coaster Brake Hub (PTCB) 404SA 3 Speed CB Hub w/ Shifter (PT3CB)
4914HC Chain 1/2x1/8x97 links (PT, PT2F) 4914M Chain Connecting Link
4914E Chain-Short (PTCB, PT3CB) 4914L Chain-Long (PTCB, PT3CB)
4914R Chain half-link:1/2”x 1/8”4916 Chain Idler Sprocket
4910P-PT-BLK Chainguard (Black Plastic)
Miscellaneous Parts
5927BLK-C Rear Basket (Black Vinyl Coating) SA14-1 3 Speed Shifter and Cable (Sturmey Archer**)
5030T Reflector Kits for Tricycles
** On 3 speed models, please note the brand and shifter style. Your Worksman PT3CB will be equipped with a quality 3 speed and shifter, but brand
and shifter style may vary. Parts listed here are the most commonly used Sturmey Archer style. For Shimano Parts, call 718-322-2000.
Accessories –Options and accessories are always being added! Visit www.worksmancycles.com for a complete list!
3979 Ding Dong Bell 3973 Battery Operated Mega-Horn
303 Squeeze Bulb Horn 3961 Cup Holder
101710 Flashing Strobe Light-White Lens 101714 Flashing Strobe Light- Red Lens
7917T1 Back Rest 133WHFront Basket w/ bracket (Easily removable w/ handles!)
7217GS12 Flashing Light Pedals (Very cool!) 202 Mini Frame Air Pump
1006 Foot Pump 201 Cable and Pad Lock w/ Key
P19 Adult Helmet
Limited Warranty: Commercial use voids this warranty. This is a consumer model. Worksman makes a full array of industrial and
recreational cycles. Shipping issues or damage must be reported within 15 days of receipt. Only one (1) warranty shipment will be made per
order, so inspect cycle fully before reporting damage. This cycle is warranted against faulty parts under the following conditions: This
warranty does not cover any failure due to accident, abuse, misuse, neglect, or as a result of normal wear and tear, or by assembly errors
performed by a non-qualified mechanic. The frame including all welded joints is warranted to be free of defects in material and workmanship
for one (1) year while in the possession of the original purchaser. All other parts on this cycle (except tires and tubes) are warranted for 90
days from date of purchase. Proof of purchase is required for any claims being considered. The manufacturer reserves the right to have all
defective parts returned at purchasers expense for examination prior to resolving the claim. If upon examination the manufacturer deems the
part to be defective and within the warranty period, a replacement part will be sent at no charge. Unauthorized repair of parts voids warranty.
Proper maintenance is required for the warranty to be valid. If it is determined by the manufacturer or the dealer that the part in question is
not covered under warranty, we will advise the cost to repair or replace the part. The sole responsibility of the manufacturer pursuant to the
terms of this warranty is the replacement or repair of the parts in question. The liability of the manufacturer shall in no event exceed the
original purchase price of the model and the manufacturer shall not be liable for any consequential damages of any nature including but not
but not by way of limitation damages for personal injuries or to property. This statement constitutes the exclusive expression of warranties
by the manufacturer and is in lieu of any and all other warranties including expressed warranties, any implied warranties, including but not
limited to warranties of merchantability and fitness or purpose, are limited in duration to one year of purchase for the frame (excludes fork)
and ninety (90) days for other parts as covered in this warranty. Cycles are not intended for off road use, stunt riding or similar activities.
Should an approved electric bicycle assist be added to the cycle, the purchaser is responsible for meeting any local laws. Such modifications
void warranty. Void where prohibited by state law. The seller is not responsible for typographical errors or omissions. Manufactured by
Worksman Trading Corporation.
Braking System
&
Recommended Weight Capacity
FT Drum FT Caliper C/B 3 Speed C/B Recommended
Weight Capacity
PT X 210
PT2F X X 215
PTCB X X 225
PT3CB X X 225
Visit www.worksmancycles.com to see our full line of quality Worksman Cycles!

- 6 -
When you need a unique specialty cycle, call
WORKSMAN CYCLES!
INDUSTRIAL HEAVY-DUTY TRICYCLES
Worksman Adaptable Tricycles
Worksman Front-Load Tricycles
Worksman Executive Trike
Worksman Chariots
Worksman Mover Tricycles
WORKSMAN HEAVY-DUTY INDUSTRIAL & DELIVERY BICYCLES, CRUISERS, FOLDING BICYCLES
WORKSMAN RECREATIONAL TRICYCLES FOR ADULTS AND CHILDREN
www.worksman.com 888-3-WHEELER