RC4WD Trail Stomper User manual

R C 4 W D
W W W . R C 4 W D . C O M
1855 Little Orchard St.
San Jose CA, 95125
E-mail: [e-mail]
1/10 Trail Stomper Ready to Run Truck

To Prevent Serious Personal injury and/or property
damage, operate all remotely controlled models in a
responsible manner as outlined below.
Choose the right location to operate your remote control
model.
1. Do not run on public streets or highways.
2. Never operate your R/C near people or animals.
3. Do not operate in confined spaces.
4. Do not operate indoors.
Inspect your R/C before operation.
1. Make sure all screws and nuts are tightened properly. It is
a good idea to use thread-locker on all metal to metal lo-
cations.
2. Make sure your transmitter batteries are fresh, or fully
charged.
3. Always run a test of your transmitter and truck before
setting on the ground.
After operation of your R/C model
1. Turn of receiver first, then turn off the transmitter.
2. Be careful handling your R/C batteries as they can be hot.
3. Keep your RC model clean and free of excess dirt and
debris.
4. Perform regular maintenance to the drive line parts of
your R/C model.
1
Precautions
10
RC4WD T-Stomper
Check out
www.rc4wd.com
for more new products.
You can also find a line of
shirts and beanies.

9
RC4WD T-Stomper
Warranty Information
RC4WD Limited Warranty
All RC4WD product is warranted to be free of defects in ma-
terials and workmanship when new. Our limited warranty
does not cover damages due to normal wear and tear, user
error of assembly or installation, user modifications, user's
failure to perform routine maintenance, addition of aftermar-
ket parts or option parts. This warranty lasts as long as the
original purchaser owns the product. In the event of a defect
under this warranty, RC4WD will, at our discretion, replace
the product, provided our inspection indicates that an origi-
nal defect exists. RC4WD reserves the right to replace any
product which is no longer available with a product of com-
parable value and function. If RC4WD determines the repair
is not covered under warranty guidelines, we will contact
you to discuss your options.
If you have any questions, please contact us via email at
[email protected]
E Q U I P M E N T R E Q U I R E D
Batteries
RC4WD T-Stomper
2
8 AA Batteries for the
Transmitter.
Hex wrenches
1.5mm,2.0mm,
2.5mm,3.0mm.
7mm nut driver
Side cutters
Long needle nose
pliers
1 7.2 Volt Battery with
Tamiya style plug for the
truck, or Lipo Battery. Out-
cry ESC can handle up to 4
cell Lipo Battery.
E Q U I P M E N T R E C O M M E N D E D
Lexan scissors
Modeling knife
Threadlocker
(medium/blue)
Spray paint for the body.
Other items

RC4WD T-Stomper
3
This is an instruction sheet for the new Outcry ESC (Electronic Speed Control). This will cover basic questions
about the ESC and how it works. If you have further questions about it’s the ESC. Please contact oursupport line,
or use our forum.
The Outcry ESC is has a built in non-adjustable drag break. The ESC comes with a BEC (battery eliminator
circuit). This allows you to get full power to the other electronics in your setup.
This ESC is a simple Plug and Play unit.Use the equipped plugs and install to your electronics. Make sure your
radio is plugged in, plug the batteryinto the ESC, and turn on your ESC. This should program everything and
then your ESC should be ready to use.
1. ESC Plugs and wires
In the photos below you can see the different wires coming from the Outcry ESC. We have used the dual motor ESC for
these photos. The only difference between the single version and dual version are the extra two motor wires on the dual
version.
A. In this photo you can see the ESC On/Off switch and the receiver throttle input plug. You will notice the red wire to the
receiver throttle input plug has been removed and heat shrink applied. This is to allow the BEC to apply full power to the
receiver and other electronics in your setup. It is very important to leave the shrink wrap on the red wire. (Removing the
shrink wrap can cause damage to the ESC and your other electronics)
The receiver plug will install into the throttle slot of your receiver. Please refer to your radio’s owner manual for instruc-
tions on which slot to plug the throttle control plug into.
B. This photo shows the BEC and battery plugs. The ESC is equipped with a standard Tamiya plug. This should make it
an easy plug and play for your battery connections. (changing the plug may void your warranty)
The plug on your BEC is a standard receiver plug. This will plug into two different spots on your receiver. Either your
Auxiliary, or Battery slots. Refer to the owner’s manual that came with your radio for these slots.
C. The motor wires are shown in this photo. Again the dual motor ESC was used for this manual. The single motor ESC
will only have the two motor wires. One black and one red. The dual motor has two blackand two red.
We do not recommend removal of the fan from the ESC.
2. Receiver plug installation
We recommend you refer to your radios owner manual to help with this step.
Plug the receiver throttle control plug in the throttle control slot of your receiver. Plug the BEC plug into your Auxiliary,
or Battery control slot on you receiver.
Make sure the red wire with the heat shrink is up and out of the way. This is not supposed to be plugged into the receiver.
E S C I N S T R U C T I O N S
8
RC4WD T-Stomper
Warning Before Use
Warning before use
An RC Model is not a toy. If misused, it can cause serious bodily harm and damage to prop-
erty and people. Operate only in open areas, following all instructions included here.
This is a sophisticated hobby product and not a toy. It must be operated with caution and
common sense and requires some basic mechanical ability. Failure to operate this product
in a safe and responsible manner could result in injury or damage to the product or people
and other property. This product was not designed for use by children without close adult
supervision. Please make sure to read over all safety warnings before operating this prod-
uct.
Damage Limits
RC4WD shall not be liable for special indirect or consequential damages, loss of profits or
production or commercial loss in any way connected with the product, whether such claim
is based in contract, warranty, negligence, or strict liability. Further, in no event shall the
liability of RC4WD exceed the individual price of the product on which liability is asserted.
As RC4WD has no control over use, setup, final assembly, modification, or misuse, no liabil-
ity shall be assumed nor accepted for any resulting damage or injury. By the act of use,
setup or assembly, the user accepts all resulting liability.
If you as the purchaser or user of this product are not prepared to accept liability associated
with this product, you are advised to return this product immediate in new unused condi-
tion to the place of purchase.
Warnings, Precautions and Safety
As a user of the product, you are solely responsible for operation it in a manner that does
not endanger yourself and others or result in damage to the product or the property of
others.
Carefully follow the directions and warnings for this and any optional support equipment
(chargers, batteries, and battery packs, etc) that you use.
This model is controlled by a radio signal that is subject to interference from many sources
outside your control. This interference can cause momentary loss of control so it is neces-
sary to always keep a safe distance in all directions around your model, as this margin will
help to avoid collisions or injury.
 Always operate your model in an open area away from cars, traffic, and people.
 Avoid operation your model in the street.
 Never operate your model in populated areas.
 Never operate your model with low transmitter or receiver batteries.
 Keep this and all electrical items out of reach of children
 Avoid water exposure to all electrical equipment. This product was not designed and
protected from this purpose

RC4WD T-Stomper
7
Stock Replacement parts
X-0496 Front and Rear Axle set (plastic)
Z-B0006 Yota Body set
Z-S0022 Steering kit
X-0427 Plastic axle parts
X-0093 Rear straight axle shafts (pair)
X-0273 Heavy duty front shafts (pair)
X-0409 Servo and 4 link mount
Z-S0200 Heavy duty spool for axle
X-0364 Lower 4 link/shock mounts
Z-W0036 Stamped Steel Black beadlock wheels (4)
X-0251 Scale 90mm white shocks (2)
Z-C0007 Chassis
X-0195 R2 single speed transmission
X-0329 Replacement gears for R2
X-0319 8 tooth 32 pitch pinion
X-0324 Front Punisher Shaft
X-0252 Rear Punisher Shaft
Z-T0006 1.55 Mud Slinger tires (2)
Z-R0007 XR2 Radio and receiver
Z-R0005 XR2 receiver
Z-E0007 Outcry ESC (w/bec)
Z-S0076 BEC for ESC
Z-E0012 Mayhem High Torque servo
X-0212 M3 Conical washers
X-0392 Velcro hold down straps (5)
X-0337 RC4WD Sticker sheet
Z-E0004 45 turn motor
Z-S0073 Plastic M3 Rod end
X-0274 Bevel Shaft
Optional Replacement parts
P A R T S L I S T I N G
X-0055 Chrome diff cover
X-0403 Black shock boot
X-0402 Blue shock boot
X-0075 Green shock boot
X-0401 Yellowshock boot
X-0211 6 tooth pinion
X-0318 7 tooth pinion
X-0320 9 tooth pinion
X-0008 11 tooth pinion
X-0009 12 tooth pinion
X-0113 13 tooth pinion
X-0115 20 tooth pinion
X-0317 Monster lube
Z-E0005 35 turn motor
Z-E0003 55 turn motor
Z-E0002 65 turn motor
X-0408 Dual Spring shocks
X-0358 Black R2 2 Speed
X-0361 Black R2 Dig
X-0493 Enclosed R2 Dig
X-0052 R2 Dual Dig
X-0068 Short shaft for R2
X-0393 Heavy duty R2 gears
Visit our website for many wheel and tire options for your T-Stomper RC4WD T-Stomper
4
X R 2 R A D I O I N S T R U C T I O N S

Page 6 X R 2 R A D I O I N S T R U C T I O N S
5
RC4WD T-Stomper
6
Optional Parts
Z-A0045
Aluminum (F) axle complete
Z-A0046
Aluminum (R) axle complete
X-0487
Reinforced Axle C
Z-S0092
XVD axle
Z-S0220
ARB Diff cover
Z-S0012
Hardcore diff cover
Z-S0009
Rok Trac Diff cover
X-0429
Aluminum Knuckles
X-0399
Red Scale shock boots
Z-W0045
1.55 Void Beadlock Wheels
RC4WD T-Stomper