Fisher-Price M9523 User manual

Consumer Information
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A. M9523pr-0920
©2008 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. PRINTED IN CHINA
www.fisher-price.com
Sit 'n Play M9523
Care
• Wipe with a clean cloth dampened with a mild soap and water
solution. Do not immerse this toy.
Please keep this instruction sheet for future
reference, as it contains important information.
Requires three LR44 button cell alkaline
batteries (included) for bear toy operation.
Adult assembly is required.
Tool needed for assembly: Phillips
screwdriver (not included).
Doll sold separately.
United States Only
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user’s
authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
PRESS
Press the button on the bear for musical tunes.
Battery Replacement
• Locate the battery compartment on the back of the bear.
• Loosen the screw in the battery compartment door with a Phillips
screwdriver. Remove the battery compartment door.
• Replace the batteries with three, new button cell alkaline batteries.
Hint: We recommend using alkaline batteries for longer battery life.
• Replace the battery compartment door and tighten the screw.
• When sounds become faint or stop, it’s time for an adult to
change the batteries!
1.5V x 3
LR44 or Equivalent
Battery Compartment Door
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different
types: alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to
be charged under adult supervision.
Battery Safety Information
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
Sturdy Walker
FCC Statement

Assembled Parts
Both Shown Actual Size
Note: Tighten and loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
• Fit the front brace onto one of the frames.
Hint: The front brace will only fit on the frame one way. If it does
not seem to fit, turn it around and try again!
• Insert two M3.5 x 15mm screws into the holes in the frame
and tighten.
• Fit the other frame onto the braces.
• Insert three M3.5 x 15mm screws into the holes in the frame
and tighten.
IMPORTANT! This step must be completed before attaching
the seat to the frame assembly.
• "Snap" the support bar onto the pegs on the top of the
frame assembly.
This package contains small parts in its
unassembled state. Adult assembly is required.
Take extra care during unpacking and assembly.
CAUTION
• Fit the back brace onto the same frame.
Hint: The back brace will only fit on the frame one way. If it does
not seem to fit, turn it around and try again!
• Insert an M3.5 x 15mm screw into the hole in the frame and tighten.
121
34
Seat
Back BraceFront Brace
Support Bar
Tray
2 Frames
Front Brace
Frame
Back Brace
Frame
Support Bar
Frame Assembly
Assembly
• Fit the seat onto the frame assembly. Push down on the seat to
fit in place.
1
7
Frame
Assembly
Seat
• "Snap" the tray handles into the holes in the seat.
1
5
Tray
• While holding the seat in place, turn the assembly face down.
• Insert two M4.5 x 18mm washer head screws into the holes in the
back of the seat, as shown.
• Tighten the screws.
1
8
• Insert two M4.5 x 18mm washer head screws into the holes on
the bottom of the seat, as shown.
• Tighten the screws.
1
9
• "Snap" the bear toy into the slot in the seat.
1
10
M3.5 x 15mm Screw - 8 M4.5 x 18mm
Washer Head Screw - 4
Seat
BACK VIEW
BOTTOM VIEW
• Turn the seat face down. Insert two M3.5 x 15mm screws into the
seat and tighten.
1
6